ON/OFF Button Troubleshooting Guide Press to BRIGHTEN Symptom Possible Cause Solution Erratic operation or flickering LEDs A) Loose wiring connections B) Low dim setting A) Light bulb(s) burned out B) Circuit breaker is off or tripped C) Disconnect switch on the dimmer is pulled out to the OFF position D) Improper wiring E) Defective dimmer
(RF9640-N) A) Rapid start feature is disabled (RF9640-N) B) Low dim setting
(RF9640-N) Dimmer is not included in Z-Wave network A) Replace light bulb B) Turn on the circuit breaker C) Push in the disconnect switch on the dimmer D) Check and correct wiring E) Replace dimmer A) Check and correct wiring B) Set minimum brightness to
(RF9640-N) a higher level A) Enable rapid start feature
(RF9640-N) B) Set minimum brightness to
(RF9640-N) a higher level Include dimmer in a Z-Wave network using a Z-Wave controller. Refer to Z-Wave controller user manual for details Light level indicators
(blue) LED ON/OFF indicator (amber) Light level may be adjusted with lights ON or OFF Press to DIM No Function. All LEDs are OFF Disconnect Switch Pull out to change bulbs
(Master Dimmer only) Hot 120V Black Red Green R E T S A M R E M M D I White Light Fixture Ground Neutral Neutral White Hot 120V Neutral Green Ground White Y R O S S E C C A R E M M D I Black White White Switch Identication White White ACCESSORY ACCESSORY Green d e R ACCESSORY Green Disconnect Switch Black Master Control Black Accessory Lights turns on after long delay Functions normally using the dimmer push buttons but not from Z-Wave controller and one of the blue LEDs blinks ON and OFF about once per second Functions normally using the Master dimmer control but not from Z-Wave controller and no LEDs are blinking Functions normally both locally and from a Z-Wave controller but cant be controlled from a dimmer accessory switch (RF9642-Z) or other Z-Wave device Dimmer is warm to touch after a period of time 1.1 1.3 Bare Problem with RF communica tion on dimmer
-
Replace dimmer The dimmer accessory or other Z-Wave device is not associated with the dimmer you wish to control
-
Create an association between the dimmer acces sory or other device and the dimmer. Refer to your Z-Wave controller user manual for details This is normal No action required Single Location Control Installation (requires one Master dimmer) 1.41.2 Black
- Hot Tag
-
Black To Light White 1.5 1.3 White Master Black Green Tag Black Red Black White Identify existing wiring (This switch will be a single-pole) and tag Hot wire. Use voltage tester as necessary to confirm Hot wire (Voltage will be present at the Hot wire when the lights are off). 1.4 1.6 TOP Disconnect existing switch and remove. Connect master dimmer as shown by connecting black wire of dimmer to tagged Hot wire. Red wire must be connected to the wire that goes to the light. Gently push dimmer into place and secure with mounting screws. Make sure disconnect switch at bottom of master is fully pushed in FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&
your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrls.Installation et mise en uvre de ce matriel devrait avec changeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres.