FCC ID: UH2-RF9640N Z-Wave Plus Universal Smart Dimmer

ENGLISH RF9640-N - Z-Wave Plus Universal Smart Dimmer - For dimmable LED/CFL/ INC/ MLV/ ELV/HAL/FLR RF9642-Z - Z-Wave Plus Smart Accessory Dimmer - For multi-locations WARNINGS AND CAUTIONS:

warranty. Turn circuit breaker to OFF position or remove fuse(s) and test that power is OFF before installation process. Never wire any electrical device with power turned ON. Wiring dimmer HOT may cause permanent damage to dimmer and void If you are not sure about any part of these instructions, please contact a licensed electrician. IMPORTANT: Z-Wave Universal dimmer will not work or will become damaged if wired incorrectly and warranty will be voided. Refer to wiring instructions provided. Use only with 120V/AC 60 Hz. Do not exceed maximum rating of dimmer as indicated on the device. Must be installed and used in accordance with all national and local electrical codes. If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician for installation. Use only #14 or #12 copper wire rated for at least 75 C with these devices. DO NOT USE WITH ALUMINUM WIRE. NOTES:

The Z-Wave Universal Dimmer is wired directly to the light fixture. The Z-Wave Universal Dimmer is not compatible with standard 3-way switches. For Multi-location applications (3-Way or 4-Way) the Z-Wave Accessory Dimmer (RF9642-Z) is used along with one Z-Wave Universal Dimmer. The Z-Wave Accessory Dimmer communicates via RF signals to control the light from more than one location. For multi-location control use Z-Wave Universal Dimmer Master direct wired to the light along with Z-Wave Accessory (RF9642-Z). The Z-Wave Accessory dimmer does not require direct connection to the light (use Z-Wave Association function). Z-WAVE DEVICE NETWORK INSTRUCTIONS:

This product may be added to a new or existing Z-Wave network. An Eaton Wiring Devices Z-Wave device has a blue LED, which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network. This product works with other Z-Wave products from different vendors and product categories as part of the same network. This product is a listening node and it will act as a repeater in the Z-Wave network. It will perform the repeater function with Z-Wave products from Eaton and from other Z-Wave vendors. This secure Z-Wave Plus device will only associate with other secure devices based on the Z-Wave controller its being used with. Please refer to instructions provided with the controller for more details. Adding Z-Wave Smart Universal Dimmer to a Z-Wave Network:

1. To include this device in a Z-Wave network, select the command on your Z Wave controller for inclusion (Install, Add Device, Add Node, Include Device, etc.). Then press the device ON/OFF switch one time to include it in the network. 2. Based on the controller, the controller may ask you to scan the QR code (Figure 1) or manually enter 5 digit code under the QR code 3. After the Device is added to the network, the LED will stop blinking. This indicates the device is installed in the Z-Wave network. Removing Z-Wave Smart Universal Dimmer from a Z-Wave Network:

1. To exclude this device from a Z-Wave network, select the setting on your Z-Wave controller for exclusion 2. Once your controller is in exclusion mode, press the device ON/OFF switch one time to exclude it from the network. The LED will start to install the device as a secured device. You may find this QR code on the device or included in device packaging.

(Uninstall, Remove Device, Remove Node, Exclude Device, etc.). blinking. For a Quick start Guide on how to install this device with Eatons home automation hub & other compatible Z-Wave Certified Controllers, please scan the QR code (Figure 2) Operating Instructions:

Press ON/OFF button once to turn lights ON at previously selected level. Press ON/OFF button again to turn lights OFF. When lights are OFF, press and hold ON/OFF button for 2 seconds for full brightness of overhead light. Delayed OFF: When overhead lights are ON, press and hold ON/OFF button for 2 seconds until the blue LED blinks. After the preset delay, the lights will begin fading to OFF (Default present delay is 10 seconds; you can configure this through a compatible Z-Wave controller for up to 2 minutes). Please refer to configuration parameters table. Amber ON/OFF LED indicates that dimmer is turned ON (Default). Dimming Level Adjustment (RF9640-N only) For maximum compatibility with different load types, RF9640-N allows the user to set the minimum dim level or low end trim. Also to save on power consumption RF9640-N allows the user to set the maximum dim level or high end trim. After adding the dimmer to a network, press ON/OFF button to turn ON the overhead light. Press and hold ON/OFF button for five seconds until the blue indicator LEDs begin to cycle rapidly (Notice - After two seconds blue indicator LEDs will start to flash indicating activation of the delayed OFF feature. Continue to hold the ON/OFF button for three additional seconds until the blue indicator LEDs begin to cycle rapidly.) Once the indicator LEDs start cycling, release the ON/OFF button. Dimmer will set the light to the previously saved minimum level. During initial setup, the light will set to the factory minimum default. Press either the dim UP or DOWN buttons to change the minimum level until the light output is acceptable. Once light output is acceptable, press ON/OFF button once. Blue indicator LEDs will start to cycle rapidly again and the dimmer light will go to previously saved maximum level. Press either the dim UP or DOWN buttons to change the maximum level until the light output is acceptable. Press ON/OFF button once, LED will flash indicating completion of programming. Note - User could ignore setting max or min while programming by pressing ON/OFF button without changing the light level. Rapid start feature (RF9640-N only):

This feature ensures that LED/CFL lights turn on when the dimmer preset level is low. With this setting enabled, the lights may momentarily come ON brighter than the preset level (less than one second) and then dim down to the preset level. Depending on the type of light used, this feature may not be needed. To enable/disable the feature, turn lights ON. Press and hold the ON/OFF button for 10 seconds until the blue indicator LEDs flash for the third time, then release the button. This feature is disabled by default. Changing LED Indicator brightness: (RF9640-N & RF9642-Z):

This feature allows the change of the brightness of the blue LED indicators on the device. There are 5 levels (including fully OFF and full brightness) to change the LED indicator brightness level either while the device is ON or OFF state. Changing the LED indicator brightness when the device is an ON state:

Turn the overhead light ON. Press and hold the ON/OFF button for 15 seconds till the LED indicator flashes for the fourth time. (second time for RF9642-Z) Release the ON/OFF button. Use the dim UP or DOWN button to change the LED indicator level (it will cycle between the five levels). Once the brightness level is selected, double tap on the ON/OFF button and this value will be saved. Changing the LED indicator brightness when the device is an OFF state:

Turn the overhead light OFF. Press and hold the ON/OFF button for 15 seconds till the LED indicator flashes for the second time. Release the ON/OFF button. Use the dim UP or DOWN button to change the LED indicator level (it will cycle between the five levels). Once the brightness level is selected, double tap on the ON/OFF button and this value will be saved. Local Reset (RF9640-N & RF9642-Z) (Please use this procedure only when the network primary controller is missing or otherwise inoperable) The device could be reset locally. This will cause the device to be excluded from its network and restore to factory default. Before leaving the network the dimmer will send a notification to the controller indicating its departure from the Z-Wave network. Turn the device ON. Press and hold ON/OFF button for 20 second till the LED flashes for the fifth time. (third time for RF9642-Z) Release the ON/OFF button. LED will start flashing rapidly. Once the LED starts blinking slowly, that indicates the device is not part of the network. ON/OFF Button Press to BRIGHTEN Single Location Control Installation (requires one Master Dimmer) Two Location Control Installation (requires one Master and one Accessory) Light level indicators

(blue) LED ON/OFF indicator (amber) Light level may be adjusted with lights ON or OFF Hot 120V Black Red Press to DIM Green White Light Fixture Hot 120V Y R O S S E C C A R E M M D I Black White Green Ground White White Hot 120V Black Red Green Ground Neutral R E T S A M R E M M D I White White Light Fixture Neutral RF9642-Z LOCATION A RF9640-N Disconnect Switch Pull out to change bulbs

(Master Dimmer only) Switch Identification White White ACCESSORY ACCESSORY Green d e R ACCESSORY Green Disconnect Switch Black Master Control Black Accessory Quick Start Guide Figure 2 Figure 1

(For Reference Only) R E T S A M R E M M D I White RF9640-N Ground Neutral Neutral Neutral Wattage Ratings Load Type Single Gang 2-Gang INC/ELV/FLR/HAL/MLV RF9640-N CFL/LED 600W 300W 550W 300W 3-Gang 500W 300W Configuration parameters:

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Delayed OFF Time Panic ON Time Panic OFF Time Not Used Power Up State Panic Mode Enable Dimmer Ramp Time Kickstart Enable/Disable Reset Max/Min Levels to factory default Not Used Set Minimum Dimming Level Set Maximum Dimming Level BLUE LED Brightness Level while the dimmer is ON BLUE LED Brightness Level while the dimmer is OFF Amber LED Brightness Level while the dimmer is ON Amber LED Brightness Level while the dimmer is OFF 0-4 Value 0 to 127 secs 0 to 127 secs 0 to 127 secs N/A 1=OFF 2= ON 3 = Last State 0=OFF 1=ON 0 to 127 secs 0 Disables 1 Enables 0 N/A 1 to 99 1 to 99 0-4 0-4 0-4 Value 0 to 127 secs 0 to 127 secs 0 to 127 secs N/A 1=OFF 2= ON 3 = Last State 0=OFF 1=ON 0 to 127 secs N/A 0-4 0-4 Delayed OFF Time Panic ON Time Panic OFF Time N/A Power Up State Panic Mode Enable Dimmer Ramp Time 1 2 3 4 5 6 7 13 14 15 16 8-12 Not Used BLUE LED Brightness Level while the dimmer is ON BLUE LED Brightness Level while the dimmer is OFF Amber LED Brightness Level while the dimmer is ON 0-4 Amber LED Brightness Level while the dimmer is OFF 0-4 Association groups supported:

Group 1 (lifeline) 5 node maximum Group 2 (ON/OFF) 5 node maximum Group 3 (DIM Up/ DIM Down) 5 node maximum Parameter Description Parameter Description RF9640-N RF9642-Z www.eaton.com www.eaton.com/wiringdevices EIS-0239-E (REV.B) www.eaton.com www.eaton.com/wiringdevices EIS-0239-E (REV.B) ENGLISH RF9640-N - Z-Wave Plus Universal Smart Dimmer - For dimmable LED/CFL/ INC/ MLV/ ELV/HAL/FLR RF9642-Z - Z-Wave Plus Smart Accessory Dimmer - For multi-locations Troubleshooting Guide Symptoms Device doesnt function. All LEDs are OFF Possible Cause Solution A) Circuit breaker is Open or tripped B) Air Gap switch on the dimmer is pulled out to the OFF position C) Improper wiring D) Defective dimmer A) Turn ON/Close the circuit breaker B) Push in the disconnect switch on the dimmer C) Check and correct wiring D) Replace dimmer Erratic operation or flickering LEDs A) Loose wiring connections B) Low dim setting (RF9640-N) A) Check wiring and following instructions provided with the device B) Set minimum brightness to a higher level (RF9640-N) Lights turn ON after long delay A) Rapid start feature is disabled (RF9640-N) B) Low dim setting (RF9640-N) A) Enable rapid start feature (RF9640-N) B) Set minimum brightness to a higher level (RF9640-N) Device functions normally using the dimmer push buttons but not from Z-Wave controller and one of the blue LEDs blinks ON and OFF about once per second Dimmer is not included in Z-Wave network Include dimmer in a Z-Wave network using a Z-Wave controller. Refer to Z-Wave controller user manual for installation instructions Device function normally but cant add the device to the Z-Wave network and LED is blinking A) The device is far from controller B) Not following the instructions of how to add a device to a network A) Start the installation process with the devices closer to the controller first B) Refer to the controller manual Device functions normally using the dimmer push buttons but not from Z-Wave controller and no LEDs are blinking Device functions normally both locally and from a Z-Wave controller but cant be controlled from a dimmer accessory switch (RF9642-Z) or other Z-Wave device Controller cant communicate with the device Go through Local Reset procedure and re-add the device to the network The dimmer accessory or other Z-Wave device is not associated with the dimmer you wish to control Create an association between the dimmer accessory or other device and the dimmer. Refer to your Z-Wave controller user manual for details Dimmer is warm to touch after a period of time This is normal No action required FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1: This device may not cause harmful interference, and 2: This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-

ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION:

Any changes or modifications not expressly approved by Eaton Wiring Devices could void the users authority to operate the equipment This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. EATON WIRING DEVICES LIMITED 2 YEAR WARRANTY Eaton Wiring Devices warrants its Dimmer to be free of defects in materials and workmanship in normal use and service for a period of two years from date of original purchase. THIS TWO (2) YEAR LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS, OR LIABILITIES, EXPRESSED OR IMPLIED (INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS IN DURATION IN EXCESS OF TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER PURCHASE). NO AGENT, REPRESEN-

TATIVE, OR EMPLOYEE OF EATON HAS AUTHORITY TO INCREASE OR ALTER THE OBLIGATIONS OF EATON UNDER THIS WARRANTY. To obtain warranty service for any properly installed Eaton Dimmer that proves defective in normal use send the defective Dimmer prepaid and insured to Quality Control Dept., Eaton Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269; in Canada: Eaton Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8. Eaton will repair or replace the defective unit, at its option. Eaton will not be responsible under this warranty if examination shows that the defective condition of the unit was caused by misuse, abuse, improper installation, alteration, improper maintenance or repair of damage in shipment to Eaton. EATON SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OF THE DIMMER, OR FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR ANY SPECIAL, INCIDENTAL, CONTINGENT, OR CONSEQUEN-

TIAL DAMAGES OF ANY KIND, RESULTING FROM DEFECTS IN THE DIMMER OR FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THE EXCLUSIVE REMEDY FOR BREACH OF THE LIMITED WARRANTY CONTAINED HEREIN IS THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT AT EATONS OPTION. IMPLIED WARRANTIES (IF ANY) INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABIITY, ARE LIMITED IN DURATION TO A PERIOD ENDING TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. IN NO CASE SHALL EATONS LIABILITY UNDER ANY OTHER REMEDY PRESCRIBED BY LAW EXCEED THE PURCHASE PRICE. Some states do not allow the exclusion or limitation of incidental or consequential damages or allow disclaimers or modifications of or limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some Canadian provinces do not allow exclusion or variance of implied warranties so that some or all of the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province. Read enclosed instructions carefully. If you have any questions concerning use or care of this product, please write: Consumer Service Division, Eaton Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269. www.eaton.com www.eaton.com/wiringdevices EIS-0239-E (REV.B)

Cooper Wirrng Devrces lno Request for Confi dentiality Date: 2021-2-12 Subject: Confidentiality Request for:_ PursuanttoFCC47CRF0.457(d)and0.459andlCRSP-100,Section l0,theapplicantrequeststhatapartofthe subject FCC application be held confidential. FCC ID: UH2-RF9640N Type of Confidentiality Requested

! Short Term

! Shortterm I Short term

! Short Term I Short Term I Short Term E Short Term I ShortTerm E ShortTerm

! Permanent f Pennanent*1

! Permanent I Perrnanent

! Perrnanent I Pennanent

! Perrnanent*

*Note:

(lnsert Explanation as Necessary) Exhibit Block Diagrarns External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BoM Tune-Up Procedr,rre Schematics Test Setup Photos User's Manual Cooper Wirinq Devices Inc has spent substantial efforl in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "cornpetition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confi dentiality:

The applicant requests the exhibits listed above as permanently confidential be pennanently withheld frorn public review due to materials that contain trade secrets and proprietary infonnation not customarily released to the public. Short-Term Confi dentiality:

The applicant requests the exhibits selected above as shoft tenn confidential be withheld from public view for a period of _0_ days from the date of the Grant of Equiprnent Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the prodLrct to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure plrrsLrant to FCC Public Notice DA 04-170s. NOTE for Industry Canada Applications:

The applicant understands that until such tirne that IC distinguishes between Shoft Tenn and Pennanent Confidentiality, either type of rrarked exhibit above will sirnply be marked Confidential when submitted to lC. Sincerely, By: &

(Signature/Title) Erik Gouhl

(Print name)

Cooper Wiring Devices lnc POWER OF ATTORNEY DATE: 0211212021 To:

Federal Communications Commission Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 We, the undersigned, hereby authorize TA Technology (Shanghai) Co., Ltd. /Yuan Jingjing on our behalf, to apply to FCC on our equipment for FCC lD:uH2-RF9640N. Any and all acts carried out by TA Technology (Shanghai) Co., Ltd. / Yuan Jingjing on our behalf shall have the same effect as acts of our own. w@Signature :

Print name: Erik Gouhl Company: Cooper Wiring Devices lnc

Cooper Wiring Devices Inc Date: February 12,2021 Federal Communications Cornrn ission Authorization and Evaluation Division 7435 Oakland Mills Road Colurnbia, MD 21046 Attn: OE'l'Dept. Ref: FCC Class II Pelmissive change 1br l'CC ID: UlI2-RF9640N Original Grant Date: 10123/2018 Applicant: Cooper Wiring Deviccs Inc Dear Examiner, l'his is to request a Class II permissivc change fbl FCC ID: tlH2-RF9640N, originally granted on 1012312018. The maior change flled under this application is:

1. The RF cilcuit board t'errains unchanged, while the powel board adds a switching cir.cuit and a BLUII line 2. Added a 3-way control line Sincerely yours,

'ru=e/"a--

Name: Erik Gouhl

'l-itle: Director', Engineeling Company: Cooper Wiring Deviccs Inc Telephone: +1770 631 2140