NS-CAHBTEB01_15-0047_QSG_V1_EN_FINAL.ai 1 3/12/2015 3:27:50 PM NS-CAHBTEB01_15-0047_QSG_V1_EN_FINAL.ai 1 3/12/2015 3:27:50 PM Final flat size: 304.8 x 177.8 mm Final fold size: 76.2 x 177.8 mm PACKAGE CONTENTS Bluetooth Headset USB charging cable Earbuds (small and large) Quick Setup Guide FEATURES High-quality stereo sound from Bluetooth 4.0 enabled devices Battery lasts 12 hours (talk), 10 hours (music) Curved design fits comfortably around the neck Inline controls easily adjust audio CHARGING YOUR HEADSET A tone sounds (every 60 seconds) and the LED flashes red when your headset battery is low. Connect the USB charging cable from your headsets charging port to a USB port. Rewind/Skip back Fast forward/Skip forward Play/Pause OFF/ON PAIRING YOUR HEADSET Pairing your first Bluetooth device 1 Slide the power switch to ON. The LED blinks red and blue and the headset enters pairing mode. Charging port Neck strap Earbud (R) Power switch O Microphone Earbud (L) Call button/LED indicator Volume down Volume up OFF/ON Before using your new product, please read these instructions to prevent any damage. OFF/ON 2 Make sure that your Bluetooth device is within 33 ft. (10 m) of your headset. 3 Turn on your Bluetooth device, turn on Bluetooth, then set your device to pairing mode. For more information, see the documentation that came with your Bluetooth device. 4 On your Bluetooth device, select NS-CAHBTEB01. The LED lights blue and a tone sounds when your headset pairs to your Bluetooth device. Quick Setup Guide | NS-CAHBTEB01 Bluetooth Headset Manually pairing your Bluetooth device 1 Press and hold (call) to enter pairing mode. The LED blinks red and blue. 2 Make sure that your Bluetooth device is within 33 ft. (10 m) of your headset. 3 Turn on your Bluetooth device, turn on Bluetooth, then set your device to pairing mode. For more information, see the documentation that came with your Bluetooth device. 4 On your Bluetooth device, select NS-CAHBTEB01. The LED lights blue and a tone sounds when your headset pairs to your Bluetooth device. Pairing two devices 1 Pair your headset to your secondary Bluetooth device first. See "Pairing your first Bluetooth device" for instructions. 2 Press and hold (call) on your Bluetooth headset to enter pairing mode. 3 Connect your primary Bluetooth device to your Bluetooth headset. See "Manually pairing your Bluetooth device" for instructions. 4 Re-pair your secondary Bluetooth device to your Bluetooth headset. See "Manually pairing your Bluetooth device" for instructions. Note: When connected to two phones, the headset calling functions will work with the primary phone. Disconnecting and reconnecting your paired device Your headset remembers up to six Bluetooth devices and will turn off after three minutes if it is not paired to a Bluetooth device. To disconnect To reconnect Turn off your headset Turn on your headset .Your headset searches for the last connected Bluetooth device and reconnects. NS-CAHBTEB01_15-0047_QSG_V1_EN_FINAL.ai 2 3/12/2015 3:27:51 PM NS-CAHBTEB01_15-0047_QSG_V1_EN_FINAL.ai 2 3/12/2015 3:27:51 PM To disconnect To reconnect Move the Bluetooth device out of range Make sure your Bluetooth device is within 33 feet of your headset. Turn off your Bluetooth device Turn on your Bluetooth device, then make sure Bluetooth is on. Turn off Bluetooth on your Bluetooth device Turn on Bluetooth on your Bluetooth device. Connect your Bluetooth device to another Bluetooth device Disconnect your Bluetooth device from the other Bluetooth device, then set your device to pairing mode. Select NS-CAHBTEB01 on your Bluetooth device. Note: If a device does not automatically reconnect, you may need to reselect NS-CAHBTEB01 on your Bluetooth device. WEARING YOUR HEADSET USING YOUR HEADSET Making phone calls Note: When your headset is connected to two Bluetooth devices, calling functions work with the primary Bluetooth device (the one that is connected second or made the last outgoing call). To make a call, use your phones controls, then select the headset as the audio source. To redial the last number on your primary phone, press (call) twice. To answer an incoming call, press (call). Note: Your headset vibrates when there is an incoming call. To switch audio between your headset and phone, use your phones controls. To reject an incoming call, press and hold (call) for two seconds. To end a call, press (call) twice. Call waiting To switch to an incoming call, press (call) twice while speaking on an active call. To switch between two active calls, press and hold
(call) for one second. To end both calls, press (call). Begin playback on your Bluetooth device. To play audio, press . To skip to the next track, press . To skip to the previous track, press . To fast forward, press and hold . To rewind, press and hold . SPECIFICATIONS Average charging time: 1.5 - 2 hours Operating time: Talk - 12 hours / Music - 10 hours Working distance: Up to 33 ft. (10 m) Battery: Lithium 200mAh/3.7V SAFETY INFORMATION/CAUTION FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause TROUBLESHOOTING Issue No sound or low volume Cannot connect with Bluetooth Solution Make sure that your Bluetooth device is turned on, Bluetooth is turned on, and NS-CAHBTEB01 is selected. Turn up the volume on your headset and Bluetooth device. Make sure that your Bluetooth device is not muted. Make sure that your headset and Bluetooth device are not paired to other devices. Shorten the distance between your headset and Bluetooth device. Turn your devices off, then on. Re-pair your headset and Bluetooth device. Make sure that your headset and Bluetooth device are not paired to other devices. Make sure that your Bluetooth device supports the HSP, SFP, A2DP, or AVRCP Bluetooth protocol. Make sure that you have selected NS-CAHBTEB01 on your Bluetooth device. Bluetooth device keeps unpairing Shorten the distance between your headset and your Bluetooth device. Recharge your headset and Bluetooth device's batteries. NS-CAHBTEB01 does not appear on my Bluetooth device Shorten the distance between your headset and Bluetooth device. Put your headset into pairing mode, then refresh your list of Bluetooth devices. For more information, see the documentation that came with your Bluetooth device. No Power Make sure your Bluetooth headset is charged. Make sure your Bluetooth headset is turned ON. harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different form that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RSS-Gen & RSS-210 statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RSS-102 Statement:
This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. Cet quipement est conforme l'exposition aux rayonnements Industry Canada limites tablies pour un environnement non contrl. ONE-YEAR LIMITED WARRANTY Visit www.insigniaproducts.com for details. CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada) 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. 2015 Best Buy. All rights reserved. Made in China V1 ENGLISH 15-0047