FCC ID: 2AL52CR00LB18 Cat. B CBD Cellular Module

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5848811.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Overview This document is an addendum to the Telit LM960 HW Design Guide, the module of which this product is based off of. There are no changes to the integration requirements of said module for all bands except for B48 (FCC Part 96). FCC Regulatory Notice Modification statement Council Rock has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the equipment. Interference statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows:

Smart Private Networks www.CouncilRock.com CR00LB18 Contains FCC ID: 2AL52CR00LB18 Antenna Approval This module is approved to be integrated with antennae at or below the maximum gain outlined in the Telit LM960 HW User Guide for all bands except 48. For Band 48 (3550MHz~3700MHz) the maximum allowable antenna gain is 15dBi. Smart Private Networks www.CouncilRock.com

Telit CROOLB18 Ce Assembled in China IME1:356299100447273 Model: CROOLB18 FCC ID: 2AL52CROOLB18 IC; 5131A-LM960

((ccanzoacoosors

[R) 003-130183 LN

=r [1] 0190118003

Apr 22, 2022 Federal Communications Commission To Whom It May Concern:

This change of identification request applies for a new FCC ID: 2AL52CR00LB18 as established for a currently approved device. This application by Council Rock Enterprises, LLC will establish a new FCC ID under its own grantee code for the purpose of marketing. The original grant to Telit Communications S.p.A, FCC ID: RI7LM960, which was originally granted on 09/11/2018, will remain in effect. An authorization letter by Telit Communications S.p.A is attached. The equipment is electrically identical. The original test results are applicable and representative of this changed device. External photographs are included in the application Should there be any question, please feel free to contact us. Operations in 1755-1780 MHz bands of this device will be under base station control per Part 27.77. Operations on any portion of frequencies in the paired 1755-1780 MHz and 2155-2180 MHz band are capable of operating on all frequencies in the paired 1710-1780 MHz and 2110-2180 MHz band, using the same air interfaces that the equipment utilizes on any frequencies in the paired 1710-1780 MHz and 2110-2180 MHz band. Operations in 600 MHz bands of this device will be under base station control per Part 27.75. Operations on any portion of frequencies in the paired 600 MHz band are capable of operating on all frequencies in the 600 MHz band, using the same air interfaces that the equipment utilizes on any frequencies in the 600 MHz band. Sincerely, David Chauncey VP Engineering Smart Private Networks www.CouncilRock.com

Council Rock Enterprises, LLC 11 Centre Park Rochester, New York 14614

(888) 970-2925 office

(585) 285-4132 fax info@CouncilRock.com Oct 14, 2021 To Whom It May Concern:

I hereby authorize PCTEST Engineering Laboratory, LLC to act on my behalf in submitting an application as stipulated in 47 CFR 2.933 for equipment authorization of FCC ID: 2AL52CR00LB18, including completing and signing FCC application forms, cover letter and confidentiality request. This authorization is valid only for the application described below:

This application applies to the Telit Communications S.p.A module, FCC ID: RI7LM960, which was originally granted on 09/11/2018 and will remain in effect, and will establish a new FCC ID:

2AL52CR00LB18. This authorization will expire on October 14, 2022 and may be revoked at any time by Council Rock Enterprises, LLC upon written notice provided by Council Rock Enterprises, LLC to PCTEST Engineering Laboratory, LLC Sincerely yours, Manuel Ochoa VP Engineering Smart Private Networks www.CouncilRock.com

Items to be covered by Single modular transmitters. Answer from applicant Oct 25, 2021 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: 2AL52CR00LB18 Federal Communications Commission 1. The modular transmitter must have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable) 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured Y Y Y Y Y Y Y Smart Private Networks www.CouncilRock.com 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Y Date: October 26, 2021 Manuel Ochoa VP Engineering Smart Private Networks www.CouncilRock.com

Authorization Letter Date: 2022-03-22 Federal Communications Commission Equipment Approval Services 7435 Oakland Mills Road Columbia, MD 21046 Subject:

To Whom It May Concern:

This application by Council Rock Enterprises, LLC will establish a new FCC ID, 2AL52CR00LB18, under its own grantee code for the purpose of marketing. We understand that Council Rock is using our exact module, certified under FCC ID: RI7LM960, as it was certified and integrating it into one of their host devices for obtaining a new original certification. The original grant to Telit Communications S.p.A, FCC ID: RI7LM960, which was originally granted, will remain in effect. Should you have any questions or comments concerning the above, please contact the undersigned. Signature VP Global Certification, R&D Paolomaria Schiratti Telit Communications SpA DocuSign Envelope ID: 2F555036-D801-48A1-9C0C-E09E5F3010FC