SN(POLIFA f0 obersye spe ednibweus spe bsrsA teebouerpye for cousbyisuce conyq AoIg spe neeL,2 Yoruce: [pe cpsusee o1 woqicsploue vos exbiezeyA sbbtoaeg pA LBVDE UVWE:COMEVILH Wage Ww [simsu Cowbyiez MUP CVAVDV SI0:
LHVL WVA CVN2E NUDE2IKED ObEBVLION IMLEKEEKEUCE KECEIAED IACI NDING IALEKEEBEUCE IALEBELEBEUCE VUD (S)LHI2@ DEAICE NN2L VCCEbBL VUA COVDILION2: (1) LHI2 DEAICE NVA UOLCVN2@E HVBWEOT ObEBVLIOU 12 2NBIECL LO LHE KOITTOMIMG LAO LHI2 DEAICE COWBIIE? ALLH BVKL 12 OL LHE ECC BNTEe INBET Ee? LIBE MOULLOB OF COR KAICE NV AZ AVE SERVICE MANNUAL This system contains 1 monitor, 1 power supply cable, and 4 sensors. Installation (recommendation: Monitor needs to be powered before installation of sensors) a, Monitor:
1. Place the monitor in a best view position. 2. Input the power supply cord into the monitor and plug the other side of power supply cord into cigarette lighter for starting display function. b.Sensors:
1. Take the vehicle to repair shop in order to deflate tire pressure, and separate the wheel and tire. 2. Remove the original valve from the wheel. 3. Screw the sensors on the valve firmly. 4. Set the wheel and tire together, and inflate the tire. Description:
-Monitor diagram Front Right Side i 4 MODE button_[ [, ~TIRE button Reset hole
~Monitors Display :
(; SAFE-P KPA PSI F He Kalen*
BAR SET-WP og E> SET-LP 9g ACT-P SAFE-P: INDICATION OF TIRE PRESSURE AT SAFE RANGE. SET-HP: INDICATION OF SETTING HIGH TIRE PRESSURE VALUE SET-LP: INDICATION OF SETTING LOW TIRE PRESSURE VALUE. ACT- P: INDICATION OF ACTUAL TIRE PRESSURE VALUE. LOW-BATT. INDICATION OF LOW BATTERY CONDITION. EXPLAINATIONS OF EACH POSSIBLE CIRCUMSTANCE WITH TIRE:
1. |; :When the power is on, the monitors screen would be under detecting condition.
:Tire pressure at high-pressure condition. Tire pressure at normal condition (SAFE-P WILL DISPLAY AT THE SAME TIME).
:Tire pressure at low-pressure condition. 2. ~+#F 5. iF Tire pressure drops dramatically. 6. tt Sensor is out of order. If tires were under 2, 4, & 5 above statements, the monitor would come out beeping sound as a warning. By pressing MODE, the beeping sound would automatically be off (the beeping sound would still be on if any of above unforeseen circumstances are still existing). By pressing MODE button, it would also be able to see the current tire pressure, temperature, pre-set high-pressure value, and pre-set low-pressure value and by pressing TIRE button it enables you to choose and check other tires TO SET A LOW PRESSURE READING:
a. Press RESET button and hold for 5 seconds until 000 displays on the LED screen. b. Press MODE button 4 times until 004 displays on the LED screen. c. Press FIRE button to begin the pressure setting. a. Now, press TIRE button for 4 pressure reading. Press MODE button for pressure reading. e. After setting, press RESET button again for confirmation (alarm will beep 3 times). TO SET A HIGH PRESSURE VALUE:
a. Press RESET button and hold for 5 seconds until 600 shows on the LED screen. b. Press MODE button 5 times until 005 shows on the LED screen. c. Press TERE button to start the pressure setting. Press FIRE button for | pressure value. Press MODE button for + pressure value. e. After setting, press RESET button again for final confirmation
(alarm will sound 3 times). Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.