2M HD IP Indoor PIR Cube Camera Quick Manual Ver. 1.0 / 2020.10 Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference. Safety Informaon CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUNCTIONS. ATTENTION:
IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLAE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGEES CONFORMMENT AUX INSTRUCTIONS. Important Safety Instrucons 5. When installing the camera, fasten it securely and rmly. A falling camera may cause personal injury. 6. Do not place conducve objects (e.g. screw drivers, coins, metal things, etc.) or containers lled with water on top of the camera. Doing so may cause personal injury due to re, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locaons. Doing so may cause re or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Connued use in such a condion may cause re or electric shock. WARNING 1. Read these instrucons. 2. Keep these instrucons. 3. Heed all warnings. 4. Follow all instrucons. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 9. If this product fails to operate normally, contact the nearest service center. Never manufacturers instrucons. 10. When cleaning, do not spray water directly onto parts of the product. Doing so may apparatus (including ampliers) that produce heat.
- There is a risk of explosion if the baery is incorrectly replaced. The baery should be replaced only with the same baery.
- Used baeries must be disposed of according to local regulaons or baery manufacturer's instrucons. Disposing of in a re or in a hot oven, or mechanically crushing and cung may cause an explosion. disassemble or modify this product in any way. cause re or electric shock.
- Leaving the baery in a very high temperature or low air pressure environment may result in an explosion or leak of ammable liquids or gases. CAUTION This symbol indicates that dangerous voltage consisng a risk of electric shock is present within this unit. 1. Do not drop objects on the product or apply strong shock to it. Keep away from a locaon subject to excessive vibraonor magnec interference. This exclamaon point symbol is intended to alert the user to the presence of important operang and maintenance (servicing) instrucons in the literature accompanying the appliance. 2. Do not install in a locaon subject to high temperature low temperature or high humidity. Doing so may cause re or electric shock. To prevent damage which may result in re or electric shock hazard, do not expose this appliance to rain or moisture. WARNING WARNING then move or reinstall it. 4. Remove the power plug from the outlet when then there is a lightning. Neglecng to do so may cause re or damage to the product. 5. Keep out of direct sunlight and heat radiaon sources. It may cause re. 1. Be sure to use only the standard adapter that is specied in the specicaon sheet. Using any other adapter could cause re, electrical shock, or damage to the product. 6. Install it in a place with good venlaon. 2. Incorrectly connecng the power supply or replacing baery may cause explosion, re, 7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this electric shock, or damage to the product. may damage the image sensor. 3. Do not connect mulple cameras to a single adapter. Exceeding the capacity may 8. Apparatus shall not be exposed to dripping or splashing and no objects lled with cause abnormal heat generaon or re. liquids, such as vases, shall be placed on the apparatus. 4. Securely plug the power cord into the power receptacle. Insecure connecon may 9. The Mains plug is used as a disconnect device and shall stay readily operable at any 7. Do not block any venlaon openings. Install in accordance with the 8. Do not install near any heat sources such as radiators, heat registers, or other 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched parcularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 12. Use only with cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. 13. Unplug this apparatus when a cart is used. Use cauon when moving the cart/apparatus combinaon to avoid injury from p-over. 14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 3. If you want to relocate the already installed product, be sure to turn o the power and 11. Only use aachments/accessories specied by the manufacturer. To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that the plug is easily accessible. cause re. me. 1. Product & Accessories 2. Part Name 3. Installation Lens Mic LED PIR Sensor Lan Port DC12V Port Speaker Illuminaon Sensor SD Card Slot Alarm In/Out Port Reset/WPS Camera Cable Hole. 30600130 Template Sheet Screw &
Plasc Anchor-2pcs Before installing your camera, you have to read the following cauons. 1. You have to check whether the locaon can bear ve mes of the weight of your camera. 2. Dont let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or re. 3. When installing your camera, dont allow any person to approach the installaon site. If you have any valuable things under the place, move them away. 1 2 3 Using the template sheet, install the bracket. Connect the cables through the Body to the cable ports respecvely. Turn and ghten to connect Body and Bracket. 4 Adjust the bracket to the desired view. Reset to the Factory Default Press the reset buon for 5 seconds to return the setup to the factory default. Warning:
If you press the Reset buon, you will lose all seng data. If needed, please, make a note for further installaon. 4. Cabling 1 3 2 5. IP Installer 3 2 4 Device Setup N.O N.C State Close Open Supervisor Up Down Input Level 0V ~ 2.3V 2.3V ~ 3.3V 0V ~ 1.0V 1.0V ~ 3.3V 0V ~ 1.0V 1.0V ~ 2.5V 2.5V ~ 3.3V 3.3V ~ 2.3V 2.3V ~ 0.8V 0.8V ~ 0V Value 1 0 0 1 0 1 2 2 1 0 1 Power Connecon Please, check the voltage and current capacity of rated power carefully. Rated Power Power Consumption PoE 3 Alarm In Unlike general alarm functions, device types are classified into N.O / N.C /
Supervisor according to the level of voltage supplied to both input and Gnd. DC 12V 3.96W IEEE 802.3af Class3 2 Network Connecon Alarm Out In the RELAY OUT menu of WEB, the left is 1 channel / the right is 2 channels, and if checked, it is closed between OUT and GND of the corresponding channel, and when unchecked, it is open. At this time, if checked, the JIG's OUTPUT check LED turns on. 1. Run IP Installer 1 Run the manual CD and IP installer in S/W folder. Click on Network Adaptor selecon Menu
(NIC) aer run this program. Select a network which a camera is connected then click on a Search buon. (Takes about 5 sec.) Select a camera to set. The informaon of the selected camera will be shown at Device Info. 2 3 4 5 6 Select the network type. The default network type of the camera is DHCP mode. If you have a DHCP server, it will automati
-cally set the Camera IP. If you do not have a DHCP server, Camera IP is set to 192.168.1.80 after one minute. 6 5 7 8 9 10 11 12 7 Input IP seng informaon when the network type is set to STATIC. Default TCP/IP information
- IP: 192.168.1.80
- Subnet Mask: 255.255.255.0
- Gateway: 192.168.1.1
- DNS : 168.126.63.1 8 Change the port as necessary when the network type is set to STATIC. A Port Forwarding has to be set for external access to the camera. Refer to the manual of the network hub for Port Forwarding settings. An additional change of HTTPS, RTSP port can be done at Web Viewer >Admin page. 9 Input ID and PW of the camera for authencaon. Make sure to change the ID and PW for security reason. Go to Web viewer>Setup>System>
Users Management for ID and PW change. The ID and PW will be set to default value when factory reset the camera. Default ID / PW : admin / admin 10 Make sure to click on Save buon to save changed values. An Apply message will be popped-up when the settings are applied normally, or an error message will be popped-up when failed. Disposal of Old Appliance Preparing to mount the camera FCC Instrucons 1. When this crossed-out wheel bin symbol is aached to a product it means the product is covered by the European Direcve 2002/96/EC. 2. All electrical and electronic products should be disposed of separately form the municipal waste stream in accordance to laws designated by the government or the local authories. 3. The correct disposal of your old appliance will help prevent potenal negave consequences for the environment and human health. 4. For more detailed informaon about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product. 1. The mounng surface must bear ve mes the weight of your camera. FCC ID : 2AX2S-NST8-22-R 2. Do not let the cables get caught in improper places or the electric line cover to be damaged. This may cause a breakdown or re. FCC Compliance Statement 3. CAUTION: These servicing instrucons are for use by qualied service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operang instrucons unless you are qualied to do so. 4. This product is intended to be supplied by a UL Listed Power Supply Unit marked Class 2 or LPS or PS2 and rated 12 Vdc, 0.33A min or PoE (802.3af), 0.11A. 5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as dened in UL60950-1 or PS2 as dened in UL62368-1. 6. Unit is intended for installaon in a Network Environment 0 as dened in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building. 7. Using the mounng template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling. 6. Web Viewer Screen 11 12 To reboot or reset (except network seng) the camera. Select a camera (multiple camera can be selected) > Input ID and PW > Click on Reboot or Factory Reset button. Able to delete an Acve-X which is installed when accessing to Web Viewer. You dont need the function because this camera use the VLC plugin instead of the Active-X. 1 3 2 4 5 6 7 8 Web viewer is optimized with explorer10 or above version and Firefox. 4 Below Menu is supported in accordance with models. If VLC is not installed or VLC plugin is not supported (Chrome), Live buffering and Channel select menu on 3, 4 will be changed to Live Viewer menu, and then if HTML5
(MJPEG) is selected on Live Viewer menu, then you can check the video. PTZ Control This camera model does not support the zoom and focus. Speaker Control /Alarm Input/ Relay Out Supported. 1 2 3 Live video display. This is the region for live video stream from the camera. Setup popup button. Click it to open the Setup page to setup details of IP camera like Video, Network, Events, System and etc. When the image goes unsmoothly because of bad network connection, it stored image during setup time and shows the image on the live view screen. User will see the delayed images as much as setup time. 5 Motion. It shows the Motion event status. Event Alert Icon ( )appears if Motion Detection is activated. 6 Camera Time. Display the camera time. 7 PIR. The maximum number of counters is 99. 8 Auto Clear. If you press the Auto Clear button, it is automatically cleared after a certain time after PIR motion occurs and the counter does not increase. PIR counter is initialized by pressing Pir clear button. This device complies with part 15 of the FCC rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Cauon Any changes or modicaons not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier. FCC Radiaon Exposure Statement This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier.