Model: @DSKSAO1 Weather Guard / Knaack 420 E. Terra Cotta Ave Crystal Lake, IL 60014 USA Weather Guard / Knaack 185A Courineypark Drive East Mississauga, ON |.5T 2T6 800-456-7865 Toll Free 800-334-2981 Fax Knaack.OrderEntry @ wernerco.com 888-562-2251 Toll Free 888-456-8460 Fax Knaack.OrderEniry.Canada @ wernerco.com 24-0326 A 5430 ENGLISH ACAUTION feather guardi, ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. Be safe - always wear protective eye wear to keep debris out of your eyes when installing WEATHER GUARD Truck Products Tools Needed NEEDLE NOSE PLIERS
* PHILLIPS HEAD & STANDARD HEAD SCREWDRIVER
* WIRE STRIPPER -
= 5/16" WRENCH OR SOCKET POWER DRILL
* WIRE CRIMPER
* HEAT GUN
* TIN SNIPS Page 2 Saddle Box USER INSTRUCTIONS Installation Kit Includes:
1]
SYSTEM MODULE Qty. 4 QUICKDRAW REMOTE (FOB) ary. 1 WEATHER GUARD EXTREME PROTECTIONLOCK ae QTY. 2 -CLIPS, GASKETS AND KEYS INCLUDED ANTENNA aty.1 g=opek= ACTUATOR & LINKAGE ASSEMBLY QTy.1
. a WIRE HARNESS - BATTERY QTY.1 WIRE HARNESS - SADDLE-BOX QTY. 1 SYSTEM MODULE COVER Ory. i ACTUATOR ASSEMBLY MOUNTING BRACKET QTY. 1 WIRE HARNESS COVER PLATE ary. 1 ADHESIVE SQUARES QTY.8 WIRE TIES QTY.8 VELCRO STRIPS - LARGE arTy.2 VELCRO STRIPS - SMALL | QTy.2 ACTUATOR MOUNTING SCREWS (M3.9 X 25mm) QTY.4 aa SELF TAPPING MOUNTING SCREWS (#8-18 x 1/2) QTy.7
: Page 3 ENGLISH fe ENGLISH weather quar. Contents 1, SYSTEM MAINTENANCE .... I]. MAXIMIZE THE PERFORMANCE OF YOUR SYSTEM... -.csesseresssecetercsetnerne 6 HI. QUICKDRAW SADDLE BOX COMPATIBILITY ...--snerercnecasnee IV. MECHANICAL ASSEMBLY AND INSTALLATION sneresnenenstesennpensennsssceneesnunn 6 V. INSTALLING QUICKDRAW SYSTEM MODULE -vsns-.--sscsseneneersnenearansnenenensne 12 VI. SYSTEM CHECK VIL FINAL INSTALLATION ...ccsscencosscussnnencnnscecrinsnnnsusanorsnsensenesouuenegnazervounsensnanne 6 Vill. OPERATING INSTRUCTIONS FOR REMOTE CONTROL (FOB) wsescssesron 7 IX. PAIRING THE FOB TO THE QUICKDRAW SYSTEM...
| MODEL:IL-TXPKE-001 Model:PKE9185-10 1O Wo agegh LPKE FCC ID: W99-PKE9185-10 ! The label information is also i included in the user manual. 1C:8296A-PKE918510 |
This device complies with part15 of The FCC Rules and Canada licence-exempt RSS-210 standard. Operation issubjectto the fellowingtwo conditions:
(1)This device may not cause harmfulinterference and
{2]This device mustaccept any interference received, includinginterference that may cause undesired operation,
| MODEL:IL-TXPKE-001-NB FCC ID:W99-IL.PKE ne IC :8296A-ILPKE The label information is also included in the user manual. Page 4 Saddle Box USER INSTRUCTIONS FCC&IC FCC&IC Caution:
This device complies with Part 15 of the FCC Rules and Canada licence-exempt RSS-210 standard. Operation is subject to the following two conditions:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFEERENCE THAT MAY CAUSE UNDESIRED OPERATION. Le manuel d'utilisation des appareils radio exempts de licence doit contenir I'nonc qui suit NE ep at x te ou l'quivalent, a un endroit bien en vue et/ou sur les appareils :
Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en comprometire le fonctionnement. The following safety warning must be observed at all times:
Due to the complexity of this system, installation of this product must only be performed by an authorized Weather Guard dealer. Congratulations on purchasing your QuickDraw Keyless Access System. Due to ihe complexity of this system, it must be installed by an authorized dealer only. Installation of this product by anyone other than an authorized dealer voids the warranty. By carefully reading this Owner's Manual prior to using your system, you will maximize the use of this system and its features. You can print additional or replacement copies of this manual by accessing our web site at www.weatherguard.com. I. System Maintenance The system requirs no specific maintenance. Your QuickDraw remote is powered by a small coin cell lightweight 3-volt lithium battery (CR2022) that Jasts approximately 3 years under normal use. When the battery begins to weaken, the operating range is reduced. ENGLISH
. Page 5 ENGLISH leather quar i. li. Maximize the Performance of Your System Never put the key fob together wiih a cellphone as this may affect the range and its performance. Additional antennas can be installed to extend the range of the active zone. The installation must be done by technicians who are trained or certified by Weather Guard dealers (optional parts and extra labor required). Refer to your authorized dealer for more information.
{H. QuickDraw Saddle Box Compatibility*
QuickDraw Weather Guard Mode! Box Type Model Material Truck Configuration T16-3-02 Steel 116-6-02 1170-02 Alum 1176-02 Alum 128-0-01 Alum 123-5-02 Alum 126-3-02 Steel 426-5-02 Steel QDSKSA01 Saddie 1270-02 Alum 1276-02 Alum 128-3-01 Sieel 136-3-01 Steel 137-0-01 Alum 1875-01 154-0-01 154-5-01 Lo
*Excludes Weather Guard low-profile and e-line models IV. Mechanical Assembly and Installation a. Open the Weather Guard saddle box and remove the lock mechanism cover plates and the locking rod cover plates as shown in Figure 1. Safely store cover plates and screws for use at the end of installation. Page 6 Saddle Box USER INSTRUCTIONS b. Remove the lock retaining clips for both locks as shown in Figure 2. Then remove both locks from the box by pulling straight out. Save the retaining clips for use with the new locks. Figure 2 Page.7 ENGLISH ENGLISH Weather quar. c, Page &
Run the full size saddie box wire harness (with four (4) total connectors) siarting from the driver side and running through the lock box and along the front of the box through the latch plates and ending at the passenger side lock box. See Figure 3 PIN Figure 3 cavereast TOP VIEW SADDLEBOX HARNESS. The four (4) pin connector should remain on the driver side of the box. Do not tie down the harness at this time. See Figures 3 through 7 Figure 4 Saddle Box USER INSTRUCTIONS d. Remove the bolis from the passefiger side latch as shown in Figure 7 Figure 7 ENGLISH ENGLISH Weather quar, e. Using the (3) M3.9x25mm screws provided, attach the actuator to the mounting bracket, but do noi tighten the screws more than a few turns. Assembly can be tightened down ence step (9) is complete. See Figure 8. Figure 8 f. Assembie the actuaior linkage assembly and.attach it to the latch as shown in Figures 9 and 10. Figure 9 Figure 10 Page 10 Saddie Box USER INSTRUCTIONS g. Complete actuator and bracket assembly installation. See Figure 11. 1. Tighten the (3) screws holding the actuator to the bracket all the way down. 2. Bolt the bracket and latch back to the box using the original bolts. Be careful not to over tighten. See Figure 11. h. Plug the actuator connector into the main saddle box wire harness. See Figure 17. Figure 11 Install the new locks with switches and wire harnesses attached. Use the original locking clips and gasket to fasten the locks in place. See Figure 12. Figure 12 ENGLISH ENGLISH V. Installing QuickDraw System Module LED INDICATOR PARING BUTTON RKE ANTENNA Figure 13 Figure 14 Figure 15 Page 12 Saddle Box USER INSTRUCTIONS b. Place the QuickDraw system module on the driver side of the box, but do not fasten in place. See Figure 16. Figure 16 G, Plug the saddle box harness into the system module using the four
(4) pin connector. Plug into the connector labeled saddle box per system module diagram. d. Using locking rod cover plate (removed in step a.) from the driver side end of the box, attach the antenna to the center of the cover plate using small velcro disks (supplied) Figure 17. Run the antenna wire parallel to the saddle box harness and plug the (2) pin connector into the system module as shown in Figure 13. Figure 17 ENGLISH Page 13 ENGLISH
[uieather guard) e. Attach the (4) pin connector on the battery harness to the system module and feed the other end of the harness out of ihe box through the hole in the box partition, down the inside of the gas strut guard and exit the box through the 12v access grommet hole located on the driver side end of the box. See Figure 18. Run the harness to the truck battery and cut to length. Crimp the proper size ring terminal to each wire and apply heat fo the insulation to shrink tight to the wires. Attach the red wire to the positive batiery terminal and the black wire to the negative battery terminal. Figure 18 VI. System Check Testing the QuickDraw Remote (FOB) The QuickDraw starter kit comes complete with 1 FOB, which is pre-programmed to the System module included. If additional FOBs are desired for the system, please see FOB programming:
a. Test 1: Proximity hands-free operation
{. Bring the QuickDraw remote into range (within 5i of box). 2. Ensure truck box lid is closed and ali push button locks are in locked position. 3. Test one of the QuickDraw proximity function by depressing and holding push button lock for approximately 2 seconds.
* If truck box opens correctly, proceed to iest push the other button lock. If both push button locks work correctly, proceed with tesi 2.
* ff truck box does not open correctly, double-check all electrical connections and repeat testing. Page 14 Saddie Box USER INSTRUCTIONS b. Test 2: Push Button Remote Operation 4. Ensure truck box lid is closed and all push button locks are in locked position, and QuickDraw FOB is within 100 ft of the truck. 2. Test QuickDraw push button remote function by depressing and holding button 1.
* If truck box opens correctly, proceed with final installation steps. (Buttons 2 and 3 can be programmed for optional lo-side QuickDraw Boxes) If truck box does not open correctly, double-check all elecirical connections and repeat testing. VII. Final Installation a. Use the two large velcro disks to atiach the system module to the saddle box and use wire ties and adhesive squares to hold the wire harness in place where needed. b. Install Wire Harness Cover Measure and trim to fit as necessary. Fasten wire harness cover plate up and against the inside lip of the saddle _ box, using three of the self-tapping screws provided. See Figure 19. Tuck the wires between the ridges of the wire cover. c. Install system module cover
* Coil excess wire harnesses neaily and tle together Put protective cover in place using sloiied tabs a guides. Carefully tuck wiring underneath See Figure 20.
* Secure protective cover in place using self-tapping screws provided. Figure 19 ENGLISH Page.i5 weather guard. d. Replace both lock mechanism cover plates and both locking rod cover plates (driver side has antenna mounted to it.) See Figure 21 Figure 20 Figure 21 TRUCK CAB i) TOP VIEW [|
eesti
! MECHANISM Petey
2 a 5 Zz Ww Page 16 Saddie Box USER INSTRUCTIONS Vili. Operating Instructions for Remote Control (FOB) Your QuickDraw Remote comes equipped with dual-mode Functionality: PKE & RKE a. Proximity Keyless Entry (PKE) Hands-Free Mode. i. Directional Transmitter (inside truck box) communicates with FOB 2. Transmitter range has up to a 5 foot Range* from the saddle box 3. When box is in locked position, user can open box by depressing one of the extreme protection lock buttons. Figure 22 b. Remote Keyless Entry (RKE) Remote Open Mode 4. Remote FOB has 100* foot range* from vehicle 2. Button #1 is used fo open the saddle box. 3. Buttons 2 and 3 can be programmed to open optional lo-side boxes (boxes and quick draw kits sold separately).
* To optimize signal strength keep the FOB from direct contact with cell phones and other similar items which can cause signal interference. Figure 23 ENGLISH ENGLISH weather quar. IX. Pairing the FOB to tne QuickDraw System NOTE: FOB memory is cleared every time the sysiem begins learning mode. In this case, all corresponding FOBs will need to be re-paired by following sequence below. The QuickDraw FOB comes pre-paired to the system module. Re-
pairing of the FOBs to the system module will be required in the foliowing scenarios: When adding additional FOBs or if the module is accidently put into learning mode. ;
a. To program more than 3 FOBs (up to 10 total) see step d. (iv) b. Lost or stolen FOB (all systems FOBs must be re-paired at the same time) to program a FOB to the QuickDraw system:
1. Ensure DIP switches are in correct position (Factory Seitings):
2. EnterLearning Mode by locating and pressing the programming button 3x until red LED activates (see Figure 23) 4, Press Button 1 on the QuickDraw FOB, the LED indicator will flash and then remain solid 5. The FOB has now been paired 6. System will automatically exit Learning Mode within 30 seconds i 3 c. To pair multiple FOBs to QuickDraw system module:
Page 18 Saddle Box USER INSTRUCTIONS 4. FOB 1: perform steps 1-4 above for first FOB 2. Fob 2 through 10: perform same steps 1-4 within 30 seconds of each other until all FOBs have been paired 3, System will automatically exit learning mode within 30 seconds d. Additional features The FOB buttons can be programmed to work in one of three ways:
1. Single press - Press FOB button once to open desired box 2. Double click - Press FOB button quickly twice 3.3 second hold - Press and held FOB button for 3 seconds To program 1-3 FOBs, make sure DIP switches are in the following orientation:
a Positions Button Operation Options Single press (factory for settings) PDouble-cick [ON _ Sasmataa [ore [on [on To program 4 or more FOBs (up to 10), make sure DIP switches are in the following orientation:
a Me A
Single Press Double-click 3 second hold Page 19 ENGLISH ENGLISH weather quar. ererna=
Any modification or unintended use of this product shall immediately void all manufacturers warranties. Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or unintended use of this product. WEATHER. GUARDLLC LIMITED. LIFETIME WARRAN Se eines Meee seed t WEATHER GUARD? Products X Year Warranty Knaack, LLG (the manufacturer) warrants to the original purchaser only that WEATHER GUARD QuickDraw system (the WEATHERGUARD Product) will be free from defects in material and workmanship from the date of installation and continuing for 3 years. A copy of the original sales receipt must be supplied to the Manufacturer at the time a warranty claim is made. This warranty terminaies if the original purchaser transfers the WEATHER GUARD Product to any other person. What is Covered QuickDraw module What We Will Do to Correct Problems Subject to the limitations and exclusions described in this limited warranty. The Manufacturer will remedy defects in material or workmanship by providing one of the following remedies at its option without charge to the original purchaser for parts or labor. (a) Repairing the defective portion of the WEATHER GUARD Product or (b) replacing the entire WEATHER GUARD Product. In addition, the manufacturer may elect at Its option, not fo repair or replace the WEATHER GUARD Product, but rather issue to the original purchaser a refund equal to the purchase price paid for the WEATHER QUARD Product or a credit to be used toward the purchase of new WEATHER GUARD Product. Installation: Must be performed by authorized Weather Guard Distributor/installer This limited warranty expressly excludes:
* Defects caused by normal wear and tear, casmetic rust, scratches, accidents, unlawful vehicle operation, or modification to the product, or any typos of repair of a WEATHER GUARD Product other than those authorized or Provided by the Manufacturer.
* Defects resulting from conditions beyond the Manufacturer's control including, but not limited to misuse, overloading, or failure to assemble, mount or use the WEATHER GUARD Product in accordance with the Manufactures written instructions or guidelines included with the WEATHER GUARD Product or made available to the original purchaser.
*TOTHE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE WEATHER GUARD PRODUCT OR THE MANUFACTURER'S NEGLIGENCE. No Other Express Warranty Applies. This Limited Lifetime Warranty is the sol and exclusive warranty for WEATHER GUARD?
QuickDraw. No employee, agent, dealer, or other person is authorized to after this warranty or make any other warranty on behalf of Knaack LLC. Page 20 Saddie Box USER INSTRUCTIONS Notification Procedures if the WEATHER GUARD Product does not confirm with the terms of this limited warranty, the original owner must prompily notify the Manufacturer in writing upon discover of the nonconformity. tn order to receive the remedies under this limited warranty, ihe warranty claim must describe the nature of the nenconformity, and a copy of the original sales receipt, invoice, bill or other proof of purchase must accompany the claim. Repairs or modifications made io the WEATHER GUARD Product by other than the Manufacturer or its authorized agent will nullify this liraited warranty. Coverages under this limited warranty is conditioned at all times upon the owner's compliance with these required notification and repair procedures. Warranty claims must include reciprocal contact information and may be made via certified mail to:
Knaack LLC ATTN: Warranty Claims 420 E. Tera Cotta Avenue Crystal Lake, IL 60014 If you have any questions please, call toll free at 1-800-456-7856.
~ 2012 Knaack LLC ENGLISH Page 21 ENGLISH weather quart. NOTES Page 22 Saddle Box USER INSTRUCTIONS NOTES ENGLISH KnaackLLC ATTN: Warranty Claims 420 E. Terra Cotta Avenue Crysial Lake, IL 60014 www.knaack.com If you have any questions, please call toll free at 4-800-456-7856. -
2013 Knaack LLC iF
(eT ar] _ WERNERCO GM7210 2014 Wemer Co. 4/14