FCC ID: 2BBYH-C1020 Smart Watch

CW Watch R1 G User Guide

EN ISED This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.FCC Requirement Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Scan the QR code on the right to access it, or visit help.fitbeing.com to browse.You can find the complete product manual in Fitbeing app at "Profile User Guide".Product ManualScan the QR code on the right to access or visit help.fitbeing.com for assistance.If you encounter any problems while using the product, you can access the "Profile Help & Support" section in the Fitbeing app for assistance.Frequently Asked QuestionsHelp and Guide Do not replace the built-in battery yourself as it may pose a safety risk. Avoid forcibly opening the watch case, as it may cause short circuits and overheating. Keep the watch away from environments exceeding 60 to prevent battery leakage or explosion. While the product complies with 3ATM waterproof standards, it is not recommended for activities such as bathing, diving, or water skiing that involve high temperatures, steam, or rapid water flow. Note that the waterproof performance may be compromised if the product structure is damaged. Be aware that firmware upgrades can lead to interface and usage changes. For detailed information, please refer to the product's upgrade instructions.PrecautionsENCW Watch R1 G1.43" HD AMOLED466 466370 mAhBluetooth 5.33ATM46.8mm 46.8mm 10.8mmSupports elevationSupport compassSupport GPS0C ~ 50CiOS 13.0 and above, Android 9.0 and aboveProduct NameDisplayResolutionBattery CapacityWireless ConnectionWater resistance gardeBody DimensionAir pressure sensorGeomagnetic sensorSatellite positioningWorking TemperatureCompatible Operating SystemsKey Specifications21For optimal data accuracy, please observe the following guidelines while wearing the watch:

1. Wear the watch at a position approximately two finger-widths from your wrist bone. 2. For comfort, adjust the band to allow a finger's width between it and your wrist. This ensures both contact and fit.Wear Your WatchIt is advised to remove the watch for approximately one hour daily. If you experience discomfort or irritation like redness, tingling, or a burning sensation, take off the watch and rest your wrist. To maintain hygiene, regularly clean your watch and wrist, particularly after workouts and sweating. Avoid using hand soap, shower gel, dishwashing liquid, or cleaning wipes as they can cause skin irritation. Instead, use mild soap and fresh water to clean the band.Wear and CareENSpring barAInstall band 1. Insert the metal pin at position "A" in the hole. 2. Push and hold the spring bar. 3. Press the band into the body and release the spring bar. 4. Pull the watch band to confirm the firm installation. Spring barRemove band 1. Lift the spring bar from the groove. 2. Push and hold the spring bar. 3. Pull it out gently to remove the band. Change the BandNote:

Make sure the USB charging plug is at the same side as the crown. Ensure to use a standard USB power source with an output of 5V1A or above. Prior to charging, ensure to clean the charging contacts of the watch to eliminate any lingering sweat or moisture.To charge the watch, connect the charging cable to a USB power source. Attach the other end to the charging contact on the back of the watch. The watch will display a charging icon while it is being charged.Charge the WatchIn the Fitbeing app, navigate to the Face Gallery page to pick up your preferred watch face.Install New Watch FacesENWhen wearing the watch, it automatically measures health data such as heart rate, sleep, stress, and activity. You can also view and track this data in the application.Health Metrics MeasurementFor outdoor workouts, wait in an open area until the GPS connects. The blinking icon " " shows it's acquiring a location fix and will stop blinking upon success.To start your workout recording, access the Workout app and select a specific workout.Record WorkoutsTo change the watch face, press and hold the screen for 1 second to access the watch face gallery.Change the Watch FaceTo switch quickly between the Suggestions, Activity, Heart Rate, Sleep, Weather, or Workout tiles, swipe left or right on the watch face screen.TilesTo access the Control Center, swipe up on the watch face screen. Enable features like Silent Mode, Sleep Mode, Always-on Display, and adjust brightness and volume swiftly.Control CenterSwipe down on the watch face screen.Notification CenterCommon FunctionsENAttentions:

1. To prevent connection issues between the app and the watch, please do not pair directly within the Bluetooth device list in your phone's system settings. 2. To ensure successful pairing, please grant Fitbeing App permissions to access Bluetooth, Location, and Camera on your phone.Press 1. Press the digital crown to wake up the screen. 2. Press the digital crown to enter the app center from the watch face screen. 3. Exit the appCrown and ButtonPress the buttonRotate the crownPress the button 1. Press to start Workout quickly. 2. Long press to activate SOS.Rotate 1. Toggle between screens or navigate through menus. 2. Adjust the volume of prompt tones and phone calls.Swipe downSwipe rightSwipe leftSwipe upTouchscreen OperationSupport full-screen touch (swipe, tap, touch and hold)Get Started4Search via BluetoothCW Watch R1 GSearchSet Up a DeviceStep 2: Pair with the AppOpen the Fitbeing app and select "" on the home page. Follow the instructions to pair your " " via Bluetooth. Then you can start using the watch.Set Up a DeviceCW Watch R1 G For Android phones, go to the Google Play. For iPhone, go to the App Store.Go to the app store on your phone, search for , and install it.FitbeingStep 1: Download the Fitbeing appYou can also scan the QR code on the left to quickly go to the app in the app store, and install it.FitbeingSet up the Watch3ENNote: If the watch can't power on, it may be because the battery has drained due to long periods of inactivity. Please charge it for approximately 10 minutes and wait for it to power on automatically.Press the Digital Crown until the startup screen appears.Power On2Step 1: Thread the longer band through the first loop of the shorter band. Step 2: Adjust to a comfortable tightness, then press the holes on the longer band onto the metal pin buckle of the shorter band. Step 3: Insert the longer band into the second loop of the shorter band and tighten.Wear Your Watch1The following steps will take approximately 5 to 10 minutes, please schedule a suitable time.Start Using4Set up3Power On2Wear1You can follow these steps to use CW Watch R1 G:Steps for UseCharging cableBackFrontBandButtonScreenDigital CrownMagnetic Charging ContactsHeart Rate and Blood Oxygen SensorsMagnetic Charging CableYour CW Watch R1 GEN

Creek Wearable Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BBYH-C1020 To Whom It May Concern, Date: December 14, 2023 Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name:chen long Title: Manager

Technical Specification Antenna Mode CW06 Manufactured SHENZHEN HENGXIANGTONG ANTENNA TECNOLOGY CO., LTD. Address 606, Building E, Enterprise Aviation Technology Innovation Research and Development Industrial Park, No. 1008, Songbai Road, Sunshine Community, Xili Street, Nanshan District, Shenzhen UINT :MM Size

Picture Antenna matching circuit BT: LOOP Band Mode Name BT Bluetooth Frequency Antenna Type Antenna Max Gain 2400-2500 Metal frame

-0.52 dBi antenna BT 3-D Patten Plots BT: 2400Mhz-2480Mhz Passive Test For BT Effi

(dB)

-6.8

-6.75

-6.47

-6.42

-6.23

-6.17

-6.11

-5.98

-5.87

-5.72

-5.54 Effi

(%) 20.89 21.14 22.53 22.82 23.81 24.14 24.51 25.22 25.87 26.81 27.94 Gain

(dBi)

-1.74

-1.67

-1.42

-1.31

-1.07

-0.92

-0.68

-0.76

-0.52

-0.44

-0.39 Freq

(MHz) 2400 2410 2420 2430 2440 2450 2460 2470 2480 2490 2500

Date2023-12-13 Creek Wearable Technology Co., Ltd. Product Model Number: CW Watch R1G, LW10 FCC ID2BBYH-C1020 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:

Testing Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By: chen long Contact Listed on FCC Wesbite Title: Manager Email: 13928480585@139.com Telephone: 075526648642 On behalf of: Creek Wearable Technology Co., Ltd. Effective Date: April 2, 2020 Revision Date:

QSF 7.6.4-8 Agent Authorization Letter Template Revision: 0 Page 1 of 1

Creek Wearable Technology Co., Ltd. Model Confirmation Letter We, Creek Wearable Technology Co., Ltd. certify the product:

Smart Watch Model No.:CW Watch R1G, LW10 Their electrical circuit design, layout, components used and internal wiring are identical, Only the color is different. Signiture:

Grantee Contact: chen long Company Name: Creek Wearable Technology Co., Ltd. Date: December 14, 2023

Creek Wearable Technology Co., Ltd. Address910, 5A office building, Longguang Jiuzuan, Longhua District, Shenzhen,China Grantee code:2BBYH FRN:0033975350 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(7) Filing SUBJECT: FCC Application for FCC ID: 2BBYH-C1020 Creek Wearable Technology Co., Ltd.. certifies that, as of the date of the filing of the application, Cleveland International Trade Agency . is our designated U.S. agent for service of process for the above referenced FCC ID. Creek Wearable Technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Cleveland International Trade Agency accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: Cleveland International Trade Agency Address: 4033 St Clair Ave, Cleveland, OH 44103, USA Contact Person: Becky Deng Tel.: 216-600-0606 Email: Georgewu7012@gmail.com FRN:0033401837 Sincerely, Signed on behalf of Shenzhen Star Instrument Co., Ltd. Signed on behalf of Cleveland International Trade Agency Signature Name: chen long Signature Name:Becky Deng Title:Manager Title: Manager Date: December 13, 2023 Date: December 13, 2023

Creek Wearable Technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-12-13 FCC ID: 2BBYH-C1020 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Creek Wearable Technology Co., Ltd. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Creek Wearable Technology Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Applicant: Creek Wearable Technology Co., Ltd. Address: 910, 5A office building, Longguang Jiuzuan, Longhua District, Shenzhen, China Contact Person: chen long Tel.: 075526648642 Email: 13928480585@139.com Sincerely, Signature: