Crestron CWD7191 Two-Way RF Transceiver Module Operations Guide Regulatory Compliance Federal Communications Commission (FCC) Compliance Statement CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help Increase the separation between the equipment and receiver Industry Canada (IC) Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter, IC: 5683C-CWD7191, has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Type: Dipole, Maximum permissible antenna gain: 2.5 dBi, Impedance: 50 Ohms Industrie Canada (IC) Dclaration de conformit Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent metteur radio , IC: 5683C-CWD7191, a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Type d'antenne: Dipole, Gain admissible maximal: 2.5 dBi, Impdance: 50 Ohms To satisfy RF exposure requirements, this device and its antenna must operate with a separation distance of at least 20 centimeters from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. This document was written by the Technical Publications department at Crestron. 2013 Crestron Electronics, Inc. Crestron CWD7191 Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: CWD7191 .............................................. 1 Functions and Features .............................................................................................................. 1 Specifications ............................................................................................................................. 2 Physical Description CWD7191 with a SMD Antenna .......................................................... 3 Physical Description CWD7191 with a Dipole Antenna ........................................................ 4 Connectors ................................................................................................................................. 5 Ports ............................................................................................................................. 5 Power/I-O .................................................................................................................... 5 Setup .......................................................................................................................................... 7 Labeling ..................................................................................................................................... 7 Documentation ........................................................................................................................... 7 Operations Guide - DOC. 7439C Contents i Crestron CWD7191 Two-Way RF Transceiver Module Two-Way RF Transceiver Module:
CWD7191 Functions and Features The CWD7191 (hereafter referred to as module), with a dipole antenna or an integrated SMD antenna, is a two-way radio frequency (RF) module that utilizes the 2.4 GHz frequency band to communicate with other devices. The module operates according to the IEEE 802.15.4 specification and can be configured to minimize the possibility of interference with other devices. The module receives RF signals from one or more Crestron devices and can transmit these signals over the air for further processing (depending on the application). Functional Summary Range from 3 feet to 550 ft. Operates on one of sixteen available channels to establish optimal signal 2.4 GHz frequency band, IEEE 802.15.4 specification quality Operations Guide - DOC. 7439C Two-Way RF Transceiver Module: CWD7191 1 Two-Way RF Transceiver Module Crestron CWD7191 Specifications The table below is a summary of specifications for the CWD7191. Specifications of the CWD7191 SPECIFICATION DETAILS Power Requirements Operating Frequency Operating Ranges*
Minimum Distance Maximum Distance Indoors
(without repeater device) Available Channels Antenna (External) Antenna (Internal) Dimensions 1.3 W (5 Vdc @ 0.26 A) 2400 MHz to 2483.5 MHz (802.15.4 compliant) 3 ft 550 ft 16 (numbered 11 through 26 per 802.15.4) 2.00.5 dBi max. Gain:
Type:
Sleeve Dipole Antenna Frequency: 2.4 GHz to 2.5 GHz Connector Type: SMA Plug Reverse Polarity Connector with -36 UNS2B Screw Max. Gain: 1.8 dBi Average Gain: -1.9 dBi Type:
Frequency: 2.4 GHz to 2.5 GHz Width: 1.80 in (4.57 cm) Height: 2.00 in (5.08 cm) Depth: 0.45 in (1.14 cm) SMD
* The location and orientation of the module are important factors in the RF performance. With the unit located outside of any metal enclosures, the antenna is adjusted to achieve the best range. The range is dependent on its placement and the building in which it is used. The construction of the building, obstructions, and RF interference from other devices are factors determining the effective range of the unit. To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within 3 5 feet of each other. 2 Two-Way RF Transceiver Module: CWD7191 Operations Guide - DOC. 7439C Crestron CWD7191 Two-Way RF Transceiver Module Physical Description CWD7191 with a SMD Antenna The module, shown below, consists of various components attached to a printed circuit board. The circuit board attaches an intended SMD mounting antenna while a 25-pin D-SUB male connector is for the application-specific installation. Physical View of CWD7191 (SMD Antenna) CWD7191 Detail Views SIDE BACK SMD ANTENNA I D L E H S F R P C B 0.45 inch 1.14 cm PCB WITH RADIO D-SUB 25 PIN MALE CONNECTOR 2.00 inch 5.08 cm PIN 1 PIN 2 P1 PIN 25 PIN 24 1.80 inch 4.57 cm Operations Guide - DOC. 7439C Two-Way RF Transceiver Module: CWD7191 3 Two-Way RF Transceiver Module Crestron CWD7191 Physical Description CWD7191 with a Dipole Antenna The module, shown below, consists of various components attached to a printed circuit board. A SMA reverse polarity female antenna port is located at the edge of the circuit board for the attaching of a dipole antenna while a 5-pin double row male connector is for the application-specific installation. Physical View of CWD7191 (Dipole Antenna) CWD7191 Detail Views SIDE BACK SMA PLUG REVERSE POLARITY CONNECTOR RF SHIELD 1.5" X 1.0" X 0.24"
HEADER, 5PIN, DBL ROW 0.050" X 0.05"LS, RT ANGLE, SM P C B R F S H E L D I 0.40 inch 1.02 cm RF SHIELD PIN 2 PIN 1 P2 PIN 10 PIN 9 2.50 inch 6.35 cm inch 2.00 5.08 cm 4 Two-Way RF Transceiver Module: CWD7191 Operations Guide - DOC. 7439C Crestron CWD7191 Two-Way RF Transceiver Module Connectors Ports For the CWD7191 with a SMD antenna, the module contains a 25-pin D-SUB male connector and a 10-pin debug header. For the CWD7191 with a dipole antenna, the module contains a 5-pin double row male connector, a 10-pin debug header, and one antenna port. The diagrams and descriptions of the 25-pin D-SUB male connector and the 5-pin double row male connector are shown in the Power/I-O section. Power/I-O The 25-pin D-SUB male connector provides power to the module as well as the communication between the module and wired devices. Refer to the following table for pin assignments of the module interface connector. 1 3 5 7 9 11 13 15 17 19 21 23 25 2 4 6 8 10 12 14 16 18 20 22 24 NOTE: Pins 8, 10 and 12 provide power to the circuit card. Power/I-O Pinout Signals Pin #
Signal Pin #
Signal 1 3 5 7 9 11 13 15 17 19 21 23 25 PA7 PB3 PB4 SPI MOSI SPI MISO SPI CLK PA4 PA5 PA6 PB1/TXD PB2/RXD PB0 PC1 2 4 6 8 10 12 14 16 18 20 22 24 PC7 PC6 RESET 5V 5V 5V GND GND GND PB5 PB6 PB7 Operations Guide - DOC. 7439C Two-Way RF Transceiver Module: CWD7191 5 Two-Way RF Transceiver Module Crestron CWD7191 The 5-pin double row male connector provides power to the module as well as the communication between the module and wired devices. Refer to the following table for pin assignments of the module interface connector. 2 1 4 3 6 P2 5 8 7 10 9
(Top View) NOTE: Pin 3 provides power to the circuit card. Power/I-O Pinout Signals Pin #
Signal Pin #
Signal 1 3 5 7 9 PB2/RXD 5V SPI MISO SPI MOSI RESET 2 4 6 8 10 PB1/TXD GND GND GND SPI CLK 6 Two-Way RF Transceiver Module: CWD7191 Operations Guide - DOC. 7439C Crestron CWD7191 Two-Way RF Transceiver Module Setup Refer to the hookup diagram below, which shows the connections made to the module. Complete the connections in any order. NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within three to five feet of each other. Hardware Hookup CWD7191 RADIO MODULE 5 2 N P I 4 2 N P I 1 P 1 N P I 2 N P I CONTROL 4 2 N P I 5 2 N P I HOST PCB J 5
+5V 2 N P I 1 N P I I D L E H S F R 0 1 N P I 9 N P I 2 P 1 N P I 2 N P I C A B L E A S S Y , 2.5 IN C H 5 P IN D B L R O W FE M A LE , C O N N C . 0 1 N P I 9 N P I J3 H O S T P C B 1 N P I 2 N P I Labeling Requirements for the Host Device The host device shall be properly labeled to identify the modules within the host device. The FCC and Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the FCC and Industry Canada certification numbers of the module, proceeded by the words Contains Transmitter Module, or the word Contains, or similar wording expressing the same meaning as follows:
Contains FCC ID: EROCWD7191 Contains IC: 5683C-CWD7191 Operations Guide - DOC. 7439C Two-Way RF Transceiver Module: CWD7191 7 Two-Way RF Transceiver Module Crestron CWD7191 Documentation The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual for OEM integrators must include the following information in a prominent location. IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 8 Two-Way RF Transceiver Module: CWD7191 Operations Guide - DOC. 7439C Crestron CWD7191 Two-Way RF Transceiver Module This page is intentionally left blank. Operations Guide - DOC. 7439C Two-Way RF Transceiver Module: CWD7191 9 Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide DOC. 7439C 03.13 Specifications subject to change without notice.