U.S. FCC Part 15 Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed an operated with minimum distance 20cm between the radiator &you body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canada Regulatory Information Radio equipment Operation of 5150-5350 MHz is restricted to indoor use only. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le fonctionnement de 5150-5350 MHz est limit une utilisation en intrieur uniquement. Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The minimum distance from body to use the device is 20cm. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. La distance minimale du corps utiliser le dispositif est de 20cm. CAN ICES-3 (B)/NMB-3(B) EU Regulatory Information Support Frequency Bands and Power:
WLAN 2412-2472 MHz < 17dBm;
WLAN 5150-5250 MHz <18dBm;
WLAN 5250-5350 MHz / 5470-5725 MHz <18 dBm;
WLAN 5725-5825 MHz < 14 dBm;
follows:
The simplified EU declaration of conformity referred to in Article 10(9) shall be provided as Hereby, [CRESTRON ELECTRONICS, INC.] declares that the radio equipment type
[M202018001] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
www.crestron.com/docs/
The Crestron AM-TX3-100 and AM-TX3-100-I are USB dongles that enable the use of Miracast projection technology on computers/
laptops. Miracast is built into the Microsoft Windows 10 operat-
ing system, so no software installation is necessary. Install the Device The AM-TX3-100 and AM-TX3-100-I can be connected to computer/
laptop with USB Type-C port. NOTE:
The AM-TX3-100 and AM-TX3-100-I are functionnally identical. The AM-TX3-
100-I model is sold outside of the United States. In this document, the term AM-TX3-100 denotes both versions of the product. In the Box 1 1 AM-TX3-100(-I) USB cable Type-C NOTE:
The AM-TX3-100 and AM-TX3-100-I should not be shielded or covered when in operation. Please refer to Best Practices for: Installation and Setup of Crestron RF Products at crestron.com/manuals to avoid wireless interfer-
ence when using the device 1 Quick StartAM-TX3-100 and AM-TX3-100-IAirMedia Presentation Transmitter Make Connections Type-C Cable Share Button:
Click to start/stop Screenshare USB Type-C connector:
To computer/laptop Connection Button:
Click to start/stop Peripheral Connection 2 Quick StartAM-TX3-100 and AM-TX3-100-IAirMedia Presentation Transmitter Operation Connect to the Device Screensharing To connect to an AM-3100-WF(-I) or AM-3200-WF-(I) with a comput-
er/PC device, do the following:
Once connected AM3X00 with computer/PC, Click the Share Button once to Start/Stop presentation sharing. 1. Press and hold Setup button (3 seconds) on AM-3x00 to start NOTE: Double click the Share Button to pause the sharing. pairing mode. 2. Press and hold Screenshare button on the device to pair - the sta-
tus LED will indicate Green that pairing has been successful. Peripheral Connection NOTE:
Click the Connection Button to Start/Stop Peripheral Connection. More configuration can be accessed from the AM-3X00 Web UI.
(Peripheral connection means the webcam/mic which is connected to the AM-3X00 will be made available as a USB UVC device on the client) 3 Quick StartAM-TX3-100 and AM-TX3-100-IAirMedia Presentation Transmitter Observe the LED indicators Refer to the following table for information about the LED indicators on the device. LED indicator Color Meaning LED ring White Unpaired: Getting Ready state (breathing
(breathing effect) effect for 5 second intervals) Red Pairing in progress.
(dancing effect) Green Paired successfully.
(pulse effect)
(One interval of 5 seconds each). Green
(alternative pulse effect between top/bottom and left/right portions) Prensenting request from AirMedia appli-
cation. Light blue Upgrade in progress.
(build up effect) LED indicator Share button Color Green Red Amber Green Meaning Paired successfully Prensentation in progress. Prensentation paused.
(pulse effect) Media application. Prensenting request from Air-
Connection Green Paired successfully button Red Peripherals connected. 4 Quick StartAM-TX3-100 and AM-TX3-100-IAirMedia Presentation Transmitter Important instructions Instructions importantes Important Safety Instructions Instructions de scurit importantes WARNING: When using this product, basic precactions should always be followed, including the following:
1. Read these instructions carefully. 2. All cautions and warnings should be followed. 3. The equipment should only be used at maximum 40C
(104F) ambient temperature. 4. Opening the equipment could result in electrical shock and should only be done by qualified service personnel. 5. Protect equipment from humidity. 6. Do not insert foreign objects or liquids into the openings, this could cause a fire or electrical shock. 7. Do not use chemical detergents to cleany our device, use a soft dry cloth. 9. when it is not in use. If one of the following situations arise, equipment has to be checked by qualified service personnel:
Liquid has penetrated into the equipment. Equipment has been exposed to humidity. Equipment has been dropped and/or is damaged. Equipment has obvious sign of breakage. Equipment does not work well or you can not get it working according to users manual. 8. To avoid damage from electrical peaks unplug the device souple. Les avertissements: concernant lutilisation de ce produit doivent toujours tre fonds sur les prcautions fondamentales, notamment:
1. Lisez attentivement ces notes. 2. Tous les avertissements et avertissements doivent tre respects. 3. Lquipement ne peut tre utilis qu une temprature ambiante maxi-
male de 40C (104F). 4. Louverture de lappareil peut provoquer un choc lectrique qui ne peut tre assur que par un personnel dentretien qualifi. 5. Empcher lhumidit du dispositif. 6. Il est interdit dintroduire des objets trangers ou liquides dans louver-
ture, faute de quoi cela pourrait provoquer un incendie ou un choc lec-
trique. 7. Ne pas utiliser dappareil de nettoyage chimique et utiliser un tissu sec 8. Pour viter les dommages de crte lectrique, retirez la fiche dalimen-
tation lorsque le dispositif nest pas utilis. 9. Dans lun des cas enoncs ci-dessous, le matriel doit tre vrifi par un service qualifi:
Dispositif dinfiltration de liquide. Lquipement est expos lhumidit. Matriel tomb et/ou endommag. Lquipement a t endommag. Le matriel ne fonctionne pas correctement ou ne peut pas tre 10. Lquipement ne doit pas tre expos leau ni tre plac sur des objets remplis deau. 5 10. Do not expose the equipment to water or place object filled utilis conformment au Manuel de lutilisateur. with water on top of it. Quick StartAM-TX3-100 and AM-TX3-100-IAirMedia Presentation Transmitter