FCC ID: 2ACWK7601 Wifi Module

CT UNITE COMMUNICATION TECHNOLOGY LTD





The information contained herein is the exclusive property of ZK and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of ZK Version
V1.0 Date
2013.11.02 MODEL NAME: ZK-7601 PRODUCT NAME :1T1R150Mbps WiFi Module



1

1

 
1 CT UNITE COMMUNICATION TECHNOLOGY LTD

        






 






 


:!!
!

 


( $#("/,"6C



-&1%+.'!*)0 CT UNITE COMMUNICATION TECHNOLOGY LTD DOCUMENT No :

REV.NO : 1.5 REG.DATE :2011.12.2















MODEL NAME:  

REV.DATE :2011.12.2 1. Features ZK-7601 is the small size and low power module for IEEE 802.11b/g/n wireless LAN. ZK-7601 is based on Ralink MT7601/MT5370 solution. PAGE :2/9 IEEE 802.11 b/g/n Dual Band WLAN infrastructure Size : 26.9mm x 12.9mm x 2.4mm 2.4GHzinternal PA Two stream spatial multiplexing up to 150Mbps ANT (1T1R) Use on-chip OTP (One-Time Programmable) USB 2.0 Supports drivers for Windows Vista, 2000, XP, Linux Security : WPA,WPA2,AES(TKIP) ,IEEE 802.1X Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Ordering Information

$"

ZK-7601

'&!%(!$#

Wi-Fi Module, 1T1R 3. Label markin







ZK-7601




:

004TB5B00331

Model No

 MAC Address BAR Code

 MAC Address No.

 Product Lot No. : 1110A0401

-11 : Year

- 11: Month

- Revision No. : A

- 02 : Date

- 01 : Manufactured Process CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2 4. Block Diagram















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 3/9 Rf22G2INP/

Rf22G2INN LAN RF receiver USB USB bus Baseband MAC/

Packet Buffer/

Encrption Engine Rf22G2INP/

Rf22G2INN PA RF Transmitter System Control EEPROM/GPIO

/LED Digital controlled RF

< Fig.1 Hardware Block Diagram >

5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Storage Temperature Storage Humidity (40 ) Min

-10

-

Max

+80 90%

Unit

%

< Table 1 Absolute Maximum Ratings > . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 4/9 5. Operating Conditions Parameter Operating Temperature Operating Humidity Supply Voltage1 VDD_3.3V Min 0

-

2.7 Typ

-

-

3.3 Max 100 130 4.0 Unit

%

Vdc 6. Standard Test Conditions The Test for electrical specification shall be performed under the following condition unless otherwise specified. 1). Ambient condition Temperature :25 5

. Humidity:65%  5% R.H. 2). Power supply voltages 3.3V (5%) input power at the Module 3). Current consumption over recommended range of supply voltage and operating conditions is like below. When its tested, it must be supplied more than 2 times of maximal current. CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 5/9 7. Electrical Specifications 1) DC Characteristics Current Consumption TX Mode ( MCS7) Idle and Associated state Radio disabled state Min.

-

-

-

Typ. 95 40 20 Max.

-

-

-

Unit mA



 &(&!'(!'
$&


 ( 11Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate TX Characteristics Power Level Spectrum Mask 1st side lobes ( to fc 11MHz) 2nd side lobes ( to fc 22MHz) Modulation Accuracy (EVM) Power On/Off ramp Freq. Tolerance Chip Clock Freq. Tolerance RX Characteristics Minimum Input Level Sens (FER 8%) Maximum Input Level (FER 8%)

* Normal Condition : 25 , VDD=3.3/5V. Contents IEEE802.11b DSSS/CCK 2400 ~ 2483 MHz 1,2,5.5,11Mbps Min. 16

-

-

-

-

-15

-15 Min.

-

-10 Typ. 17

-43

-58 30 0.5

-

-

Typ.

-88

-

Max. 18

-30

-50 30 2.0 15 15 Max.

-76

-

Unit dBm dBr dBr

%

Usec ppm ppm Unit dBm dBm CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 6/9 3) RF Characteristics for IEEE802.11g ( 54Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate TX Characteristics Power Level Spectrum Mask at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance RX Characteristics Minimum Input Level Sens. (PER 10%) Maximum Input Level (PER 10%)

*Normal Condition : 25, VDD=3.3/5V Contents IEEE802.11g OFDM 2400 ~ 2483 MHz 6,9,12,18,24,36,48,54Mbps Min. 14 Typ. 15 Max. 16 Unit dBm

-

-

-

-

-15

-15 Min.

-

-20

-32

-43

-48

-34

-

-

-20

-28

-40

-25 15 15 Typ. Max.

-75

-

dBr dBr dBr dB ppm ppm Unit ppm ppm CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2















MODEL NAME :
 

DOCUMENT No :

REV.NO : 1.5 PAGE : 7/9 3) RF Characteristics for IEEE802.11n ( 54Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate TX Characteristics Power Level Spectrum Mask at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance RX Characteristics Minimum Input Level Sens. (PER 10%) Maximum Input Level (PER 10%)

*Normal Condition : 25, VDD=3.3/5V Contents IEEE802.11n OFDM 2400 ~ 2483 MHz 6,9,12,18,24,36,48,54Mbps Min. 13 Typ. 14 Max. 15 Unit dBm

-

-

-

-

-15

-15 Min.

-

-20

-32

-43

-48

-34

-

-

-20

-28

-40

-25 15 15 Typ. Max.

-75

-

dBr dBr dBr dB ppm ppm Unit ppm ppm CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE :2011.12.2 REV.DATE :2011.12.2 8. Pin Description Terminal No















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 8/9 Terminal name Terminal Voltage 1 2 3 4 5 6 7 8 9 10 11 12 NC GND UDP UDM VDD3.3V NC RF GND NC RF GND RFGND ANT1 RFGND 3.3V 1 1 6 6

,

,

,

,

. 2 2 2 2 4 4 4 4 G G G G H H H H Z Z Z Z 1 1 1 1 5 5 5 5 0 0 0 0 M M M M b b b b p p p p s s s s 7 7 12 12 CT UNITE COMMUNICATION TECHNOLOGY LTD REG.DATE : 2013.3.31 REV.DATE : 2013.3.31 9. Recommended Reflow Profile















MODEL NAME :  

DOCUMENT No :

REV.NO : 1.5 PAGE : 9/9

. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2ACWK7601 when the module is installed inside another device, the user manual of this device must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Antenna Manufacturer: Shenzhen Sunchip Technology Co, Ltd. Antenna Model: CX-803 Antenna Gain: 0.5dBi Only above antenna could be used with this modular.