FCC ID: 2AS3F-90002 Wireless Outdoor Lighting Controller Gateway, 120-277V

Installation Guide CTRL043 WARNING RISK OF ELECTRIC SHOCK Disconnect power before servicing or installing product. RISK OF INJURY OR DAMAGE Unit will fall if not installed properly. Follow installation instructions. Install in accordance with National Electric Code and local codes. CAUTION RISK OF INJURY Wear safety glasses and gloves during installation and servicing. RISK OF CHANGES OR MODIFICATIONS The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Product Certifications FCC ID: 2AS3F-90002 ISED ID: 25008-90002 HVIN: WOLC Gateway LightGrid Gateway Outdoor Wireless Control System BEFORE YOU BEGIN Read these instructions completely and carefully. FCC Statements:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To satisfy FCC/ISED RF exposure requirements a separation distance of 20 cm or more must be maintained between the antenna of this device and persons during operation. Operation at closer than 20 cm is not permitted. CAN ICES-5 (B)/NMB-3(B) This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme aux normes RSS exemptees de licence de Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes:

Cet appareil ne doit pas provoquer dinterfrences et Cet appareil doit accepter toute interfrence, y compris celles pouvant causer un mauvais fonctionnement de lappareil. Pour tre conforme aux limites dexposition aux ondes RF des normes FCC/ISED, une distance de sparation dau moins 20 cm doit tre maintenue entre lantenne de cet appareil et toute personne pendant son opration. Mettre en opration cet appareil a une distance plus rapproche que 20 cm nest pas permis. Before Installation Carefully unpack unit. Inspect for defects before installing. Check Electrical parameters. Ensure that the voltage at the pole is 120-277V. Verify that power feed is on 24/7 constant power. The LightGrid mesh will not operate properly when operating on switched power from a master timer or photocell. Plan Route to install Gateways at the locations recommended by Current Team. Gateways must be located at strategic spots in the deployment to carefully balance the way the mesh forms. Based on the pole locations of all the desired Controllers that will be installed, the Current team will perform an RF simulation and recommend where the Gateways should be installed. Failure to follow the recommended installation locations may cause areas of the deployment to have no mesh network communications, or to overload the mesh causing poor connectivity and performance. If the Gateway will be using a wired connection (fiber / Ethernet), consultation and network architecture design must be completed and approved by the Current IT Team prior to installation of any Gateways. (Note:

Current strongly recommends using Current provided cellular backhaul instead of wired connections). Where to Install Gateway Specifications Best performance will be achieved when the Gateway antenna is as high above ground level as possible. Do not install the unit inside of any other enclosure. Gateways can be mounted on a light pole up to 16 in diameter, or on a pole-like structure on a rooftop. For more details about Rooftop Mounting, see Appendix A. The Gateway is to be mounted with the pole mounting brackets horizontal, and the latch facing upwards. The Antenna must be mounted vertically. 120-277V AC Input Weight: 7 lbs. (3.2 kg) Dimensions: 7.6 x16 x11 [193 x 406 x 280mm]

Operating Temp Range: -40 to +50C Mounting the Gateway Loosen straps 1 Unpack:

Loosen the steel straps, and adjust to the pole-mounting configuration shown below. 2 Mount to Pole:

Using the provided steel straps, mount the Gateway assembly securely to the pole structure. Tighten the straps to ensure the unit will not slide or vibrate loose. 3 Mount the RF Antenna:

The RF Antenna is a separate part in the box. Insert it to the Antenna Mounting Collar attached to the Gateway pole mounting assembly, and tighten the mounting bolt to 45 lbs-in torque. 2 Installation GuideLightGrid Gateway 4 Connect the Coax RF Cable to the RF Antenna:

The RF Cable is pre-installed on the gateway assembly. Attach to the screw terminal on the bottom of the RF Antenna, and tighten securely. 5 Position the magnetic GPS Antenna on the TOP of the metal pole mounting bracket. It must be on the top bracket,facing upwards, in order to have a clear view of the open sky. This radio transmitter (IC: 25008-90002) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Type Maximum Permissible Antenna Gain (dBi) Required Impedance Laird FG9023 5 50 6 Connect AC Power Cable:

AC Power cable is not included. Power cable shall be Hard or Junior Hard Service Flexible Cord type, suitable for use with the Liquid Tight Cable Gland supplied with the box, and should have circular cross section between 0.170 0.450/[4.3- 11.4mm]. Power feed Max. torque 50 lbs-in. 6a Insert the power feed cable through the cable gland in the bottom of the Gateway enclosure. 6b Strip each wire no more than 0.25. Route the power cable as tightly as possible (avoid larger than necessary loops/slack) to the terminal block inside the enclosure. Avoid touching any other component on the Gateway circuit board. 6c Use a wrench to hold the gland body in place, preventing it from rotating, and tighten the sealing nut of the Gland to ensure a watertight seal to the cable. Max torque on sealing nut 50 lbs-in. 3 Installation GuideLightGrid Gateway LED Indicator Turn ON USB 7 8 USB Cable:

When gateway is used with an included cellular modem mounted in the enclosure, ensure the USB cable to the modem is securely plugged in to the USB port on the gateway circuit board. If the Gateway is being used with a wired (Ethernet) connection, see Appendix B for more information. Provide Power and turn ON the ON/OFF Switch. Ensure the gateway ON/OFF switch starts in OFF position. Check that input power voltage is in the range 120-277VAC and is 24/7 constant power. Turn on the input power source, then switch the gateway ON/OFF switch to the ON position. Check the indicator light underneath the Gateway ON/OFF switch. A solid green light means the gateway is powered. Example photo to send to Current Support 9 Record the Cellular Modem ID numbers. The ID numbers are found on the sticker on the inside lid of the enclosure. Take a picture or write down all numbers on the sticker, and provide these to the Current Support Team for commissioning by emailing them to lightgridsupport@gecurrent.com. 10 Close the Lid. To ensure a waterproof installation, check that no wires or other objects will be caught under the rubber seal on the housing lid. Then close the lid and lock using the latch on top. The latch can be padlocked for added security

(not included). 4 Installation GuideLightGrid Gateway Appendix A: Rooftop Mounting Example Roof Mount Structures 11 Photos show examples of rooftop installation structures for mounting the Gateway. It is the installers responsibility to select a location where the gateway antenna will be above other obstructions on the roof and will have direct line-of-sight to multiple fixtures that will have LightGrid Controllers on them. Appendix B: Ethernet Connection This instruction will not apply to the majority of LightGrid installations. The Gateway cannot be simply plugged into an Ethernet connection, it will not function properlyuse of an Ethernet wired backhaul requires approval of the network architecture, design, support plan, and connectivity implementation by the Current IT Team. Current strongly recommends the use of Current-provided cellular modem and data service as the preferred backhaul. If use of Ethernet has been approved, the installation steps are the same however the Ethernet cable must be fed into the enclosure and connected to the Ethernet jack on the printed circuit board. 1 Ethernet cable should be of circular cross-section with overall diameter in the range 0.2100.334/5.38.5mm. 2 Remove and discard the plug that is in the gland shown. 3 Remove the split rubber grommet from the threaded sealing nut. 4 Thread the Ethernet cable through the sealing nut, and snap on the rubber grommet in front. 5 Installation GuideLightGrid Gateway RJ45 5 Push the cable through the sealing gland, and plug it in to the RJ45 Ethernet jack on the circuit board. Split grommet 6 Slide the split grommet into the gland, then tighten the sealing nut to ensure a watertight seal around the cable. When tightening the nut, use a wrench to prevent the gland body from rotating. Max torque on the sealing nut: 50 lbs-in. 7 After following all of the other steps in the primary installation instructions, the customer IT lead will need to contact the Current IT team to check and troubleshoot any connectivity issues by emailing lightgridsupport@gecurrent.com. Questions Email: lightgridsupport@gecurrent.com Leave a Voicemail: 1-877-843-5590 www.gecurrent.com 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. CTRL043 (Rev 11/23/21) Installation GuideLightGrid Gateway

Product Label Content Requirements LightGrid Gateway Label contents:

a. b. Voltage field (see header of Level0 BOM) followed by 0.07A c. Date code in the form AXXYYY a. A is the manufacturing location b. c. two digits XX are the last two digits of the year (e.g. 17 for 2017) last three digits YYY are the day number of the Julian year (e.g. 057 for February 26th) PC: followed by SKU field (see header of Level0 BOM) d. Nomenclature field (see header of Level0 BOM) e. f. MAC Address of Gateway << Note: this is unique to each gateway g. h. i. j. k. l. m. Text: This device complies with part 15 of the FCC Rules. Operation is subject to the RAINTIGHT ENCLOSURE Current Lighting Solutions, LLC www.gecurrent.com FCC information ISED information Made in Mexico, HVIN: WOLC Gateway following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. n. GE Current, a Daintree company logo o. GE monogram p. UL-listed logo updated with file number Product Label Location Requirements

aN} STATI

@ Daintree LigntGria Gateway GE CUrFFCIN 120-277VAC 50-60Hz 0.07A S12289 ELWGOCGPGC PC: 93049551 01:23:45:67:89:AB:CD:EF RAINTIGHT ENCLOSURE Current Lighting Solutions, LLC www.gecurrentcom FCC ID: 2AS3F-90002, IC: 25008-90002 Made in Mexico, HVIN: WOLC Gateway This device complies with part 15 of the FCC Rules. Operation ts subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Vd STS a a a eat err 2: gram 28 3 atlanta Perrine

TO:

Jessica Browning Lead Power Electronics Engineer T +1 216 462 4540 jessica.browning@gecurrent.com Date: September 17, 2020 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AS3F-90002 To whom it may concern:

We, the undersigned, hereby authorize SGS North America, Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Current Lighting Solutions, LLC. This authorization is valid until further written notice from the applicant. Title: Lead Power Electronics Engineer Name (Printed): Jessica Browning Signature:

On behalf of Company: Current Lighting Solutions, LLC Telephone: 216.462.4540 1975 Noble Road, East Cleveland, Ohio 44112 www.gecurrent.com

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Current Lighting Solutions, LLC 1975 Noble Rd; East Cleveland, OH 44112 Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Jessica Browning 2AS3F 2AS3F-90002 jessica.browning@gecurrent.com 216.462.4540 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: December 14, 2020 Print Name:

Title:

Jessica Browning Lead Power Electronics Engineer

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Jessica Browning Lead Power Electronics Engineer T +1 216 462 4540 jessica.browning@gecurrent.com Federal Communications Commission 7345 Oakland Mills Road Columbia MD 21046 USA Subject: Change of Identification Authorization, FCC ID: 2AS3F-90002 Date: December 14, 2020 To Whom It May Concern:

We, the undersigned, have entered into an agreement with Savant Technologies LLC, dba GE Lighting, a Savant Company who has authorized our marketing of their existing certified product as specified under 47CFR 2.933 of the FCC rules. The original identification is:

Original Company Name:

Original Model:

Original FCC ID:

The original granted date is:

Savant Technologies LLC, dba GE Lighting, a Savant Company WOLC Gateway PUU90002 September 3, 2013 We are aware of the intent to market the product with new identification:

New Company Name:

New Model:

New FCC ID:

Current Lighting Solutions, LLC WOLC Gateway 2AS3F-90002 The documents on file with FCC from the original certification remain unchanged and continue to be valid. Sincerely, Name:

Title:

Date: December 14, 2020 Jessica Browning Lead Power Electronics Engineer 1975 Noble Road, East Cleveland, Ohio 44112 www.gecurrent.com

GE Lighting, a Savant company Savant Technologies LLC 1975 Noble Road, East Cleveland, OH 44112 Subject: Change of Identification Authorization, FCC ID: PUU90002 Federal Communications Commission 7345 Oakland Mills Road Columbia MD 21046 USA Date: November 13, 2020 To Whom It May Concern:

We, the undersigned, hereby authorize marketing of our product under new identification as specified under 47CFR 2.933 of the FCC rules. The original identification is:

Original Company Name:

Original Model:

Original FCC ID:

The original granted date is:

Savant Technologies LLC dba GE Lighting, a Savant Company WOLC Gateway PUU90002 September 3, 2013 We are aware of the intent to market the product with new identification:

New Company Name:

New Model:

New FCC ID:

Current Lighting Solutions, LLC WOLC Gateway 2AS3F-90002 Sincerely, Paul Smith Systems Engineer Safety & Regulatory 216 266 2189 paul.smith@ge.com