Product Overview The Daintree Wireless Wall Dimmer is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ Connect application. The WWD2-4IW device installs into an existing junction box to replace the existing wall-mounted switch with a wireless solution that enables dimming and on/off commands to be delivered to the luminaires in its commissioned space. The communication with the Daintree system utilizes a secure and reliable wireless connection which helps minimize installation costs and complexity. Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Installation Guide Installation of Back Housing onto Junction Box 1 Disconnect power to the junction box 2 Remove the junction box cover plate 3 Uninstall existing wall switches from the junction box. 4 Reconnect wires (previously connected to wall switch) with wire nuts. 5 6 Install the back housing(s) of the wall dimmer(s) into the wall box. For proper installation into a dual gang junction box, the tabs between adjacent back housings must be removed. Carefully observe the correct orientation (the UP arrow should be in the upper right corner on each back housing). After double checking the product orientation, break off the necessary tabs using pliers. 2 DOUBLE CHECK PRODUCT ORIENTATION BEFORE BREAKING OFF TABS. The wall dimmer will only install into the back housing in one orientation. Break off tabs only after the correct product orientation has been confirmed. Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Installation Installation Guide 1 Use a standard screwdriver to remove the devices from the back housing 2 3 Insert the back housing piece into the junction box and secure with two screws. Separate the battery cover from the device. Pull the plastic insulation strip out of the battery compartment. Put the battery cover back on the device. 4 Install the main body of the device into the back housing. 5 Install the faceplate onto the device. Note: Device supports the use of other standard faceplates on the market. Network Reset To reset the network of the device, remove the faceplate from the device. Then press and hold the reset button for 5 seconds. Install the faceplate back onto the device. Press either dimming up or down button to enter the pairing mode to join the device to a network. 3 Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Personality Change Installation Guide 1 Hold the reset button and 2nd button for 5sec to change the personality to dual zone mode. Button Change 2 Hold the reset button and 4th button for 5sec to change the personality to scene mode. 1 Squeeze the clip on the side of the button to take off the button module from the devices 2 Remove the individual buttons and replace with the new set of buttons. 3 Please contact your agent if you would like customized buttons. 4 Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Battery Replacement Installation Guide 1 The devices LED flashing every 30 seconds indicates that the batteries need to be replaced. 2 Remove the device from the back housing. 3 Separate the battery cover from the device. Replace the batteries with AAA batteries. All batteries need to be replaced at the same time. 4 Install the main body of the device into the back housing. 5 Install the faceplate onto the device. The device will rejoin its network automatically. Product Dimensions 5 Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Product Operation Button Functionality Installation Guide First Button Short press Double short press Hold Second Button Short press Double short press Hold Third Button Short press Double short press Hold Forth Button Short press Double short press Hold Lights ON at previous level Lights ON at 100% output Turn ON and dim up Lights OFF Lights ON at the lowest output Dim down when lights ON Lights ON at previous level Lights ON at 100% output Turn ON and dim up Lights OFF Lights ON at the lowest output Dim down when lights ON LED Indicator Rapid flash (12 times per second) Device is trying to join a ZigBee network for up to 30 seconds Solid ON for 10 seconds Device successfully joined a ZigBee network Flashes once (100ms duration) Device has been activated while in the network Flashes ON 2 seconds every Batteries need to be replaced 30 seconds Flashes twice (100ms duration) Device has been in zone personality Flashes four times (100ms duration) Device has been in scene personality 6 Installation Guide Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Technical Data Product Specifications Dimensions Weight Power Supply battery life Mounting Warranty 114mm H x 70mm W x 36mm D 130g
(4) AAA1.5V battery 5yr (normal operation) Operating Environment
-10C to 40C Indoor Use Only) Status indicator Network joined/Button triggered Surface mounted, screw hole in backplate, cover could be removed 5 years Product Availablity Product Certifications SKU DESCRIPTION 93141338 Daintree Networked Wireless Wall Dimmer ARTICLE NO. WWD2-4IW FCC ID: 2AS3F-WWD2IW IC: 25008-WWD2IW Sensing Control E486320 7 Daintree Networked Wireless Wall Dimmer
(WWD2-4IW) Installation Guide Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information Product Name: Wireless Wall Dimmer Model No: WWD2-4IW Suppliers Name: Current Lighting Solutions, LLC Suppliers Website: www.gecurrent.com Suppliers Address (USA): Cleveland, Ohio Suppliers Phone: 1-866-855-8629 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) Lappareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC RF Exposure Statement: Specific Absorption Rate (SAR) is a measure of the rate of RF (radiofrequency) energy absorption by the body from the source being measured. This equipment has been found to be exempt from the RF Exposure SAR Evaluation when the device is installed such that a person's head will, in normal conditions, be 10mm away from the transmitter and antenna of the device. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help www.gecurrent.com 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. DT041-Daintree-WWD2-4IW-Wall-Dimmer-Installation-Guide