For additional help during Remote Control programming and set up, visit www.currentproductscorp.com/support, where you can read our other support materials or view our instructional videos. Or, you can reach our customer service department at 850-435-4994. REMOTE CONTROL Quick USER GUIDE The optional remote control provides the user with added functionality for controlling their blinds. The remote control contains single push ability to move the slats open, closed, or to your favorite position. The remote also allows the user to set up separate channels to control specified blinds for customized control. Tilt Up/ Left Full Up/ Left Full Open Tilt Down/ Right Full Down/ Right Channel Selector Favorite CH CH 1 1 1 1 432 432 432 432 5 5 5 5 Channel LEDs REMOTE BUTTON DESCRIPTIONS TILT TOGGLE Briefly press and release to move the slats in the open or closed direction and stop at the next position setting. There are seven (7) position settings from the full up to the full down position. The user may also press and hold the toggle button until the slats get to the desired position, then release the Moves the slats to the full up position for horizontal blinds or full right toggle. FULL UP/ LEFT FULL OPEN position for vertical blinds. Moves all slats to the full open position. position for vertical blinds. FULL DOWN/ RIGHT FAVORITE Moves all slats to the full down position for horizontal blinds, or full left The user can program this button to any position they choose to be their most preferred position; however, if left unchanged it will move the slats to approximately half way between the full open and the full down/ left position. Used to customize control of multiple blinds on a single remote. The currently selected channel is indicated by the Channel LEDs. Pressing the CHANNEL Button once will display the current channel. Pressing it again will switch to the next channel. When all LEDs are lit, the remote is selected to broadcast CHANNEL SELECTOR on all channels. SETTING UP THE REMOTE PAIRING THE REMOTE Pairing to the remote can be performed before or after installation and programming of the SMART WAND. Determine which blind(s) you wish to pair to the handheld remote. Press the PROGRAMMING BUTTON on each SMART WAND you wish to pair to the remote until you hear a SINGLE BEEP (1) [Fig. 1], then release. Figure 1;
Push and Hold Press the CHANNEL button until the LEDs reflect the desired channel you wish to set [Fig. 2]. CH CH 1 1 1 1 432 432 432 432 5 5 5 5 Figure 2; Push Channel Button Use a tack or pen to press and release the PAIRING button on the back of the remote [Fig. 3] When this button has been pressed, the LEDs on the front of the remote will scroll to confirm. To PAIR, press the top left button on the tilt toggle [Fig. 4]. The blind(s) will jog down and up showing that it has received the command and completed the process. If you ever need to unpair, you can repeat the same steps and press the bottom button on the tilt toggle to unpair [Fig. 5]. Figure 3; Press in Tack CH CH 1 1 1 1 432 432 432 432 5 5 5 5 CH CH 1 1 1 1 432 432 432 432 5 5 5 5 Figure 4; Push To Pair Figure 5; Push to Unpair SETTING THE FAVORITE BUTTON The FAVORITE Button allows the user to program a slat position unique to the user which moves all slats included on that channel to the users favorite position. To program the FAVORITE Button, twist the SMART WAND until the desired position is reached. Next, press and hold the PROGRAMMING BUTTON on the SMART WAND until you hear a TRIPLE BEEP (3), then release. [Fig. 6]. Your FAVORITE Button is now programmed to move that blind to your favorite position. Each SMART WAND can be set to have different favorite positions. After the SMART WAND is set, test by moving your blinds, then pressing the FAVORITE Button. All blinds on that channel should move to their programmed favorite position. Figure 6; Push Programming and Hold Button Changing the Batteries The SMART WAND Remote is powered using (1) 3V 2032 coin cell lithium battery. To replace the battery, use a small flat head screwdriver to gently pry the back off of the remote body. Once removed, the coin cell battery should be visable. Slide the coin cell battery down until it comes out of the battery holster. Inset the new battery by sliding it up into the battery holster. Replace the remote backing. 1995 Hollywood Ave. Pensacola, FL 32505 850-435-4994 SAFETY INFORMATION WARRANTY INFORMATION LIMITED WARRANTY Current Products Corp. (the Manufacturer) hereby warrants to Customer that the Smart Wand (the Product) is and will remain for a period of one
(1) year from the date of delivery to Customer as evidenced by Customers proof of purchase (the Warranty Period), free of defects in materials and workmanship, provided that the Product used for its intended purpose and is properly serviced in accordance with the Users Manual provided to Cus-
tomer. Subject to the foregoing, if at any time during the Warranty Period the Product fails to conform to the foregoing warranty by reason of defects in materials or workmanship, Customer shall promptly notify Manufacturer in writing, and Manufacturer at its option shall repair or replace the defective Product or component part without charge to Customer, except for: (A) costs incurred in transporting the Products or component parts to and from Man-
ufacturers designated dealer or its manufacturing plant; and (B) charges for labor or other costs incidental to the removal or remounting of component parts repaired or replaced under this Warranty, both of which shall be borne by Customer. Notwithstanding any provision herein to the contrary, this Warranty shall not extend or obligate Manufacturer to take any action with respect to: (i) Products which have been modified, altered, installed, used or operated in a manner which is not recommended by Manufacturer, including any Products in which parts not manufactured or approved by Manufacturer have been installed; (ii) Products which have not been regularly and properly serviced in accordance with the Users Manual or which have otherwise been neglected; and (iii) ordinary wear and tear, service and maintenance and re-
placement items; (iv) the Product has been used, or attempted to be used, for other than the customary usage or for other than the Products intended use; (v) the Product has been subject to mishandling, misuse, or abuse; (vi) the product has suffered damage resulting from lightning, power surges, van-
dalism, fire, earthquake, acts of nature, or any other cause which the product was not designed to withstand; or (vii) damage to the Product cause by bat-
tery decay or corrosion. This Limited Warranty extends only to the original owner. This Limited War-
ranty is not transferable. This Limited Warranty does not cover normal wear or tear or deterioration which occurs with the passage of time. Batteries orig-
inally provided with a new product, if any, are produced by a third party and are not warranted by Manufacturer. No employee, distributor, dealer, agent or representative is authorized to change the terms of this Limited Warran-
ty in any way, to extend the warranty time periods, or to grant additional warranties, and no attempt to do any of the foregoing will be binding upon Manufacturer. EXCEPT AS SPECIFICALLY STATED IN THE PARAGRAPHS IMMEDIATELY ABOVE, MANUFACTURER MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRAN-
TY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE WARRANTY SET FORTH ABOVE AND THE OBLIGATIONS AND LIABILITIES OF MANUFACTURER THEREUNDER REPRESENT CUSTOMERS SOLE AND EXCLUSIVE REMEDIES AND ARE EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER REMEDIES, WARRANTIES, GUARANTIES OR LIABILITIES, EX-
PRESS OR IMPLIED, ALL OF WHICH ARE HEREBY EXPRESSLY WAIVED BY CUSTOMER. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT SHALL MANUFAC-
TURERS LIABILITY HEREUNDER EXCEED THE PURCHASE PRICE FOR THE PRODUCTS, NOR SHALL MANUFACTURER BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE WHATSOEVER. LIMITATION OF LIABILITY OTHER LEGAL RIGHTS This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. CAUTION CAUTION WARNING FCC STATEMENT Read all warnings and instructions prior to setting up the SMART WAND MULTI-CHANNEL REMOTE CONTROL. Failure to follow these instructions may result in property damage or serious personal injury. Do not use the SMART WAND MULTI-CHANNEL REMOTE CONTROL for anything other than its intended use. Any usage of the part of this kit outside of its intended purposes in not covered under the warranty. Existing blinds may have sharp edges. Use gloves to prevent cuts or abrasions whenever removing or reinstalling blinds. FCC: 2AJXX-CP16A Model: CP16A0402_02 IC: 22151-CP16A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and 1. This device must accept any interference received, including 2. interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by Current Products Corp. could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ-
ing interference thath may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de license. Lexploitation est autorisee aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tour brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with the radiation exposure limits in an uncon-
trolled environment. This equipment is in direct contact with the user's body under certain operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipment est conforme aux limites d'exposition aux radiations dans un environment non control. Cet quipment est en contact direct avec le corps de l'utilisateur dans des conditions de fonctionnement normals. Cet met-
teur ne doit pas tre co-localises ou oprant en conjonction avec tour autre antenne ou transmetteur. RF WARNING STATEMENT IC STATEMENT For any questions regarding safety, warranty, or liability, call 850-435-4994.