REMOVABLE BC READER FCC ID:OAH-3980917 NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modi cations to this equipment. Such modi cations could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC ID: 22752-3980917 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 80 1 DESCRIPTION 1.1 Removable barcode reader (BCR) components 1. Power key 2. Status LED 3. Connector cover 4. Slot for placement on printer 5. Scan window 6. Reset key 7. Micro-USB port 1 2 3 4 5 4 1.2 Product label PC = Product code (14 digits) SN = Serial number HW = Hardware release bottom view side view 6 3 7 XXXXXXXXXXXXXX xx:xx:xx:xx:xx:xx xxxxxx xxx xxxx xxxx xxxxxx xxx xxxx xxxx Rx 0000000000000000000 PC SN HW BT 81 1.3 Power key functions Fast push Barcode reader ON x10s Breve pressione Barcode reader OFF Trigger to scan barcode 82 1.4 Status LED lashes in stand-alone mode The status LED indicates the hardware status of the removable barcode reader. Given in the table below are the various LED signals and the corresponding barcode reader status. STATUS LED DESCRIPTION OFF ON
-
GREEN BLUE ORANGE BARCODE READER OFF BARCODE READER ON USB CONNECTED BARCODE READER ON BLUETOOTH CONNECTED BARCODE READER ON BLUETOOTH NOT CONNECTED LOW CHARGE POWER DOWN BLUE / WHITE BT DAT UPGRADE 83 1.5 Status LED lashes in docked mode The status LED indicates the hardware status of the removable barcode reader. Given in the table below are the various LED signals and the corresponding barcode reader status. STATUS LED DESCRIPTION
-
OFF BARCODE READER OFF BLUE / GREEN BLUE CHARGING BLUETOOTH CONNECTED CHARGING BLUETOOTH NOT CONNECTED 84 2 INSTALLATION 2.1 Connections Thefollowingigureshowsthepossibleconnectionsfortheremovablebarcodereader. PC USB device Power supply 5V, 1A
(not included) Standard USB cable
(not included) Standard USB cable
(not included) cable recharge data connection 85 2.2 Docking on the printer unit 1 2 3 Turn on the printer
(see section PRINTER). Place the removable barcode reader on the printer. 4 Locate the docking seat on the back of the reader The indicator lights up and and on the recharge tray of the printer. the barcode reader is ready and charging. 86 2.3 Pinout 1 5 Micro-USB INTERFACE Micro-USB type B female connector 1 +5VUSB
(out) 2 BCR_USB-
3 BCR_USB+
4 n.c. 5 GND J4 SH1 GND SH2 GND SH3 GND SH4 GND SH5 GND SH6 GND 87 88 3 OPERATION 3.1 Switch the removable BC reader on/off 1a 2a x10s Press the key to turn on the removable barcode reader... Press and hold the key for more than 10 seconds to turn off the barcode reader... 1b 2b
... or place it on the recharge tray on the printer. .. or remove it from the recharge tray and wait for the automatic power off. 89 3.2 Bluetooth pairing with the host The removable barcode reader is able to communicate with a host device using the Bluetooth technology. To pair the reader to the host device follows the procedure described below. Once that the pairing has been done suc-
cessfully, the reader will be added to the list of Bluetooth devices of the host. After the initial pairing it is not necessary to repeat the procedure. 2 4 The reader starts and turns on scanner light for about 5 seconds, before being ready for next step. If the reader is turned off, press the button to turn it on
(see previous paragraphs). Scan barcode to make removable barcode reader pairable. After the scan, device is pairable for about 2 minutes. Perform pair/connect procedure from terminal/host. 1 3 90 3.3 Barcode reading To ensure a correct reading of barcode, proceed as follows. 1 2 Base plane When the removable barcode reader is seated on the printer docking platform, place the ticket on the same base plane of printer and inside the scan area... AA
... when the removable barcode reader is used in stand-alone mode, bring the ticket to the scan area and press the key A. 91 92 4 MAINTENANCE 4.1 Planning of cleaning operations The regular cleaning of the printer keeps the print quality and extends its life. It is recommended to use only the indicated toolstopreventdamagetothedevicecomponents(seeigure).Ifyouusetheprinterindustyenvironments,youmust reduce the intervals between the cleaning operations. A. Microiberwipe B. Compressed air A B The following table shows the recommended planning for the cleaning operations. REGULARITY COMPONENT EVERY 6 MONTHS OR AS NEEDED Scan window Case Forspeciicprocedures,seethefollowingpages. TOOLS A
, B A 93 4.2 Cleaning For periodic cleaning of the removable barcode reader, see the instructions below. 3 Turn off the barcode reader
(see previous paragraphs). Clean the case of barcode reader by using a soft cloth. ATTENTION:
Do not use alcohol, solvents or hard brushes. Do not let water or other liquids get inside the device. Case 1 2 94 Scan window 1 Turn off the barcode reader
(see previous paragraphs). 2 3 4 Clean the scan window by using a soft cloth... ATTENTION:
Do not use alcohol, solvents or hard brushes. Do not let water or other liquids get inside the device. .. and clean the hard to reach points with compressed air. 95 96 5 SPECIFICATIONS 5.1 Hardware speciications INTERFACES Micro-USB Port Bluetooth SCANNER UNIT Sensor resolution Field of view Yaw, pitch and roll Focal distance Aiming LED Illumination Ambient light DECODE RANGES 5 mil Code 128 REGULATORY LEDclassiication BATTERY SPECIFICATIONS Battery Recharge power supply Recharge cycle 480 Mbit/s (USB 2.0 high speed) 4.0 (BLE) 1280 x 800 pixels Horizontal = 45 Vertical = 28 Yaw tolerance = 60 Pitch tolerance = 60 Roll tolerance = 360 19.4 cm (from front of engine) 610 nm LED 1 Hyper Red 660 nm LED Max 107 639 lux (direct sunlight) near = 7.1 cm far = 20.8 cm Exempt risk group LED product per IEC/EN 62471 Li-Po 3.7V 470mA Battery pack 5 Vdc - Max. 500mA / USB Less than 3 hours to 80%
Battery life (standby, stand-alone mode) min. 3 hours 97 BATTERY SPECIFICATIONS Power supply Medium consumption ENVIRONMENTAL CONDITIONS Operating temperature Relative humidity Storage temperature Storage relative humidity 5 V 0.3 A from 0C to +50C from 10% Rh to 85% Rh from -20 C to +70 C from 10% Rh to 90% Rh 98 5.2 Removable barcode reader dimensions Length Height Width Weight 0 6 82 24.2 NOTE:Allthedimensionsshowniniguresareinmillimetres. 82 mm 24.2 mm 60 mm 74 g 99 100 6 CONSUMABLES The following table shows the list of available consumables for the barcode reader:
DESCRIPTION CODE 44000000003400 CLEANING KIT
(for cleaning procedure, see chapter 6) 101 102 7 TECHNICAL SERVICE In case of failure, send the 4 pieces of information listed below to our support team:
1. Product code 2. Serial number 3. Hardware release To get the necessary data, proceed as follows:
1 2 XXXXXXXXXXXXXX xx:xx:xx:xx:xx:xx xxxxxx xxx xxxx xxxx xxxxxx xxx xxxx xxxx Rx 0000000000000000000 Customer Service Department:
support@custom.it
(worldwide) or support@customamerica.com
(specific for North/South American customers) Prendere nota dei dati riportati sulletichetta di prodotto
(vedere paragrafi precedenti). Inviare allassistenza tecnica una e-mail contente i dati raccolti. 103 I Y R A N M L E R P I 0 7
. 0
. v e R 0 0 1 0 0 0 0 0 0 L 4 2 6 7
:
r e b m u N t r a P CUSTOM S.p.A. World Headquarters Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY Tel. +39 0521 680111 - Fax +39 0521 610701 info@custom.biz - www.custom.biz All rights reserved www.custom.biz