FCC ID: KA2BAX1230PA1 Nuclias Cloud-Managed AX1800 Access Point

 

Quick Installation Guide

Access Point

This document will guide you through the basic

installation process for your new D-Link

Nuclias Cloud-Managed AX1800 Access Point

DBA-X1230P

Documentation is also available on

the D-Link website

Before You Begin

Hardware Overview

LED Indicators

This installation guide provides instructions for

installing the DBA-X1230P on your network.

Additional documentation is also available on the

D-Link support website.

• D-Link Nuclias User Manual: For additional

information and instructions on how to configure

the device using the D-Link Nuclias Cloud.

• DBA-X1230P User Manual: For additional

information and instructions on how to configure

the device using the web user interface.

Package Contents

This DBA-X1230P package should include the

following items:

• 1 x DBA-X1230P

• 1 x Power adapter (optional)*

• 1 x Mounting kit

If any of the above items are damaged or missing,

please contact your local D-Link reseller.

1

Figure 1: Front Panel LED

#

LED

Description

The DBA-X1230P is booting up.

The DBA-X1230P is resetting

to its default settings or is

upgrading its firmware.

1

Power/

Cloud

Blinking

green

The DBA-X1230P is connecting

to the D-Link Nuclias cloud.

Status

Solid

orange

Blinking

orange

Solid

green

Solid

red

The DBA-X1230P is in cloud mode.

The DBA-X1230P is not working

properly in cloud mode.

Table 1: LED Description

*If the power adapter is not included, it can be

purchased separately. Please contact your local

D-Link reseller.

Interface Connectors

Setup Preparation

Please ensure that the following items are readily

available before continuing the installation process:

• An active D-Link Nuclias account.

• An active Internet connection to connect to the

1

D-Link Nuclias cloud.

• A valid device license. Contact your D-Link Nuclias

service provider for more information.

3

4

2

Figure 2: Rear Connectors

# Connector

1

Lock slot

2 Console port

Description

Slot to use with the lock plate for inserting

a physical lock to secure the DBA-X1230P

to the mounting plate (optional).

Directly manage the AP with no wireless

connection through the console port.

3

PoE LAN

port

Gigabit RJ-45 port for data and

Power over Ethernet (PoE) power.

4 Power input

Input for the power adapter (optional).

Table 2: Interface Description

System Requirements

• A PC or laptop with a working Ethernet adapter

or wireless interface.

• Mozilla Firefox 52.0 or higher, Internet Explorer

11 or higher, Safari 10.1 or higher, Google

Chrome 59 or higher.

• OS X 10.8.5, Windows 7, Linux (Ubuntu 12).

2

ENGLISHPowering the Access Point

The DBA-X1230P can be powered using one of the

following two methods:

Using Power over Ethernet (PoE)

Use a standard Ethernet cable to connect the LAN

port on the DBA-X1230P to a PoE power source

device such as a PoE switch or PoE injector.

(Optional) Using the Power Adapter

Connect the power connector of the adapter to

the power input on the DBA-X1230P and plug the

adapter into a nearby power outlet.

Configuring the Access Point

Using D-Link Nuclias

Note: To use D-Link Nuclias, the DBA-X1230P must

be connected to the Internet.

The DBA-X1230P is designed to be managed through

the D-Link Nuclias cloud. Refer to the D-Link Nuclias

User Manual for detailed configuration instructions.

H

S

I

L

G

N

E

D-Link Nuclias

DBA-X1230P

Switch or Router

Switch or Router

Management

Figure 3: Connecting through D-Link Nuclias

Refer to the DBA-X1230P User Manual for detailed

configuration instructions.

Use one of the following methods to access the web

user interface:

Connecting through Ethernet

Note: The management PC must be in the same

subnet as the DBA-X1230P.

1. Use an Ethernet cable to connect the DBA-X1230P

to the management PC or to the switch or router

the management PC is connected to.

2. Open a web browser and type in the default

host name of the DBA-X1230P and press Enter.

The default host name is DBA-X1230P-XXXX

where XXXX represents the last 4 characters

of the MAC address listed on the device label

located on the bottom of the device.

3. When prompted, enter the default login

credentials:

User name: admin

Password: admin

Connecting Wirelessly

1. Connect the management PC to the default SSID

of the DBA-X1230P. The SSID will be in the format

DBA-X1230P-XXX where XXXX represents the

last 4 characters of the MAC address listed on the

device label located on the bottom of the device.

2. Open a web browser and type in the default

host name of the DBA-X1230P and press Enter.

The default host name is DBA-X1230P-XXXX

where XXXX represents the last 4 characters

of the MAC address listed on the device label

located on the bottom of the device.

1. On an Internet-connected PC, open a web

browser and go to www.nuclias.com.

Management

DBA-1510P

3. When prompted, enter the default login

2. Enter your D-Link Nuclias user name and

password.

DBA-1510P

Switch or Router

If a device’s login credentials are modified using

Nuclias Cloud, the local username and password

will also reflect the changes made. To learn more

about configuring your password, please refer to

the Nuclias Cloud manual.

Management

DBA-1510P

Management

Manual Configuration

6

D-Link DBA-1510P Quick Install Guide

Note: D-Link recommends manually configuring the

device before mounting it.

If you are unable to connect to the D-Link Nuclias

cloud, you may need to manually configure the

DBA-X1230P using its web user interface (UI).

credentials:

User name: admin

Password: admin

Attaching the Rubber Pads

The included rubber pads can be placed on the

bottom of the device to prevent the device from

damaging the surface it is placed on.

1. Remove the rubber pads from the adhesive strip.

2. Stick one pad on each foot on the bottom panel

of the access point.

3

ENGLISHMounting on a Solid Wall or Ceiling

6. Slide the DBA-X1230P onto the mounting plate.

1.

(Optional) Attach the included lock plate to the

mounting plate using the included screws.

Figure 4: Attaching the Lock Plate

Figure 8: Placing The Access Point

2. Use the mounting plate to mark the location where

to drill the holes in the wall or ceiling.

Mounting on a Ceiling Crossbar

1.

(Optional) Attach the included lock plate to the

mounting plate using the included screws.

Figure 5: Mounting Panel Marking

3. Drill holes on the markings and place the included

anchors into the drilled holes.

Figure 9: Attaching the Lock Plate

2. Clip the two included ceiling brackets onto the

ceiling crossbar. Make sure both brackets are

positioned in line with each other.

Ceiling crossbar

Figure 6: Placing Anchors

4. Align and place the mounting plate on top of the

anchors and use the included screws to secure the

mounting plate to the surface.

Ceiling bracket

Figure 10: Attaching the Ceiling Brackets

3. Using the included screws, secure the mounting

plate to the ceiling brackets.

Figure 7: Securing the Mounting Plate

Figure 11: Attaching Mounting Plate

5. Connect the Ethernet cable and power adapter

4. Connect the Ethernet cable and power adapter

(optional) to the device.

(optional) to the device.

4

ENGLISHTroubleshooting

The DBA-X1230P receives its configuration settings and

is managed through the D-Link Nuclias cloud.

If you are experiencing problems connecting to the

D-Link Nuclias cloud, check your Internet connection.

If you still cannot connect to the service, additional

configuration on the device may be required. Refer to

the DBA-X1230P User Nuclias Cloud Manual for detailed

information on how to manually configure the device.

Additional Information

For additional support, please refer to the user manual,

or visit your local D-Link support website.

Warning: The DBA-X1230P is designed to receive PoE

power only from an 802.3at compliant source, or from a

D-Link-approved power adapter. Connecting an access

point to a Power over Ethernet (PoE) device that is not

approved by D-Link can damage the equipment.

5. Slide the DBA-X1230P onto the mounting plate.

Figure 12: Securing the Access Point

Locking the DBA-X1230P

If the lock plate was attached, insert a lock through

the device’s lock slot to secure the DBA-X1230P to the

mounting plate.

Figure 13: Inserting a Physical Lock

Reboot/Reset the Access Point

If necessary, the DBA-X1230P can be manually rebooted

or reset to factory default settings.

Rebooting the Device

Press and hold down the reset button between

2 to 5 seconds and release to reboot the device.

Resetting the Device

Press and hold down the reset button between

6 to 15 seconds and release to reset the device to its

factory default settings.

Press and hold down the reset button for

more than 15 seconds and release to reset the device

to its factory default settings and force the device to

load an alternate firmware.

5

ENGLISHAppendix - Statements

ErP Power Usage

Network Standby: 7.27 watts

Switched Off: 0.06 watts

This device is an Energy Related Product (ErP) that automatically switches to a power-saving Network

Standby mode within 1 minute of no packets being transmitted. It can also be turned off through a

power switch to save energy when it is not needed.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Non-modifications Statement:

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For product

available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is

not possible.

-

-

-

-

Caution:

Note

The country code selection is for non-USA models only and is not available to all USA models. Per FCC

regulations, all WiFi product marketed in the USA must be fixed to USA operational channels only.

RF Frequency Requirements

This device is for indoor use only when using all channels in the 5.15 to 5.25 GHz frequency range. High

power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These

radar stations can cause interference with and/or damage this device. This device will not operate on

channels which overlap the 5600-5650 MHz band.

It is restricted to indoor environments only.

6

ENGLISHIMPORTANT NOTICE:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 23.7cm between the radiator

and your body.

Innovation, Science and Economic Development Canada (ISED) Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Innovation, Science and Economic Development Canada (ISED) Statement:

This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for

harmful interference to co-channel mobile satellite systems;

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites

mobiles utilisant les mêmes canaux;

Operations in the 5.25-5.35 GHz band are restricted to indoor usage only.

Les opérations dans la bande de 5.25-5.35 GHz sont limités à un usage intérieur seulement.

Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 26.6cm between the radiator

and your body.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26.6cm de

distance entre la source de rayonnement et votre corps.

Japan Voluntary Control Council for Interference Statement

この装置は、クラス B情報技術装置です。この装置は、家庭環境で使用することを目的としてい

ますが、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こ

すことがあります。

取扱説明書に従って正しい取り扱いをして下さい。

VCCI-B

7

ENGLISHJapan Voluntary Control Council for Interference Statement

This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or

television receiver in a domestic environment, it may cause radio interference. Install and use the

equipment according to the instruction manual.

電波法により5GHz帯は屋内使用に限ります。

Product and Warranty Information

To find out more about D-Link products or marketing information, please visit the website http://www.

dlink.com.

The D-Link Limited Lifetime Warranty information is available at

http://warranty.dlink.com/

8

ENGLISHVer. 1.00(WW)_90x130

2021/02/02



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D-Link Corporation 17595 Mt. Herrmann Fountain Valley, California 92708 United States Date: 2021-01-08 FCC ID: KA2BAX1230PA1 AUTHORIZATION LETTER To Whom It May Concern:

We, D-Link Corporation hereby authorizes Amanda Wu / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu / Specialist of BV CPS Taoyuan on D-Link Corporations behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Thank you!

Sincerely yours,

 

 

D-Link Corporation 17595 Mt. Herrmann Fountain Valley, California 92708 United States Date: November 23, 2020 Declaration We, D-Link Corporation , declare that the device, FCC ID: KA2BAX1230PA1, does not support any non-US channels in all the operational mode(s). All non-US frequencies, US 2.4G channel 12-

13 and Country code selection are disabled through proprietary software and are user changeable. Should you have any question or comment regarding this matter, please do not hesitate to contact us. Sincerely yours,

 

 

Date: November 23, 2020 D-Link Corporation 17595 Mt. Herrmann Fountain Valley, California 92708 United States Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Schematic Diagram Block Diagram Operational Description Software Operational Description Subject: Request for Confidentiality FCC ID: KA2BAX1230PA1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, External Photos Internal Photos Test Setup Photos Users Manual

 

 

D-Link 17595 Mt. Herrmann Street Fountain Valley,CA92708 USA Date: 2021-01-04 Power of Attorney To whom it may concern:

|, the undersigned, Brett Adair, hereby authorize the persons listed below to act on behalf of me to sign all related documents for D-Links FCC application. | am the Point of Contact for the FCC. This Power of Attorney supersedes and viods all previous Power of Attorney. Our FRN is: 0007371172 SSSBU ML Jean / Vice President

+886-2-66000123 #5650 ML. Jean@dlinkcorp.com loTSBU Hans Liu / Director

+886-2-66000123 #5836 Hans. Liu@dlinkcorp.com WSBU Alex Chiang / Director

+886-2-66000123 #2340 Alex.Chiang@dlinkcorp.com MBSBU GK Lee / Vice President

+886-2-66000123 #5551 GK.Lee@adlinkcorp.com Company Name: D-Link Co. Ltd Fax: 886-2-55509988 Company Adress: No. 289, Sinhu 3rd Rd.,Neihu District, Taipei City, 114, Taiwan, R.O.C. Authorization period: January 1, 2021 - December 31, 2022 Should you have and question regarding this power of attorney, please dont hesitate to Contact me. Sincerly, Brett Adair Gerneral Counsel D-Link Tel: (714) 885-6000 E-mail: brett.adair@dlink.com

 

 

 

 

 

 

D-Link Corporation 17595 Mt. Herrmann Fountain Valley, California 92708 United States Date: 2021-01-27 Cover Letter for re-use of Test Data To Whom It May Concern:

The initial application has been granted according to 47CFR Part 15 for FCC ID:

KA2APX2810A1; Granted on 01/15/21. The new equipment to be Granted in this new application is The two Ever applications are identical in hardware with only one minor differences as listed below:

1. Software change Application Initial Application New Application FCC ID KA2APX2810A1 FW Without cloud function With cloud fonction The change described above do not affect the radio characteristics (802.1 1a/b/g/n) of the equipment. Consequently, radio test data retrieved from the initial application FCC ID:

KA2APX2810A1 can be re-used for the FCC ID: K a equipment. However, Based on our knowledge and our engineering judgment of the device design, the changes made, the format and amount of spot-check test data are decided as below, 1. Sample amount: 1 2. Spot-check rule part, frequency band and test items FCC Rule Part Frequency Band Test Items FCC Part 15C 2412-2462 MHz 1. Sport check radiated emission FCC Part 15E 5180-5240 MHz Band edge and Harmonics 5745-5825 MHz 2. Sport check Conducted output power and AC Power Line Emission. We, D-Link Corporation is taking full responsibility to re-use these test data for its new application FCC ID: KA!

If you have any questions, feel free to contact us. Thank you. Sincerely yours, D-Link Corporation 17595 Mt. Herrmann Fountain Valley, California 92708 United States D-LINK CORPORATION No. 289, Sinhu 3rd Rd.,Neihu District Taipei City, 114, Taiwan Date: 2021-01-27 Cover Letter for re-use of Test Data To Whom It May Concern:

The initial application has been granted according to RSS-247 for IC: 4216A-APX2810A];

The new equipment to be Granted in this new application i is applications are identical in hardware with only one minor differences as listed below:

1. Software change Application Initial Application New Application IC ID IC: 4216A-APX2810A1 FW Without cloud function With cloud function The change described above do not affect the radio characteristics (802.1 1a/b/g/n) of the equipment. Consequently, radio test data retrieved from the initial application IC:

4216A-BAX1230PAI can be re-used for the equipment. However, Based on our knowledge and our engineering judgment of the device design, the changes made, the format and amount of spotcheck test data are decided as below, 1. Sample amount: 1 2. Spot-check rule part, frequency band and test items IC Rule Part Frequency Band Test Items RSS-247 2412-2462 MHz 1. Sport check radiated emission RSS-247 5180-5240 MHz Band edge and Harmonics 5745-5825 MHz 2. Sport check Conducted output power and AC Power Line Emission. We, D-Link Corporation is taking full responsibility to re-use these test data for its new application I!

If you have any questions, feel free to contact us. Thank you. Sincerely yours, D-LINK CORPORATION No. 289, Sinhu 3rd Rd.,Neihu District Taipei City, 114, Taiwan

- Vi - /

wee a, Af, w Jea: Vice fof D- LINK CORPORATION Tel: +886-2-66000123#5650 E-mail: ML.Jean@dlinkcorp.com