Quick Installation Guide This document will guide you through the basic installation process for your new D-Link Nuclias Cloud-Managed Wireless VPN Gateway DBG-X1000
- One (1) DBG-X1000 One (1) 12V/2A Power Device Status LEDs and Ethernet Port LEDs About This Guide Item Feature Description This guide gives step by step instructions for setting up D-Link DBG-X1000. Please note that the model you have purchased may appear slightly different from those shown in the illustra-
tions. Unpacking the Product Open the shipping carton and carefully unpack its contents. Please consult the packing list located in following information to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local D-Link reseller for replacement. Adapter
- One (1) Console Cable (RJ45-to-DB9 Cable)
- One (1) Ethernet (CAT5 UTP/Straight Through) Cable
- Four (4) Rubber foot
- Two (2) Antenna Product Overview This chapter provides detailed descriptions of the DBG-X1000 device and its components. Front Panel A B C D E LED
(Top to bottom) USB Port (1) Power LED: Indicates the device is powered on. It can support various USB 2.0, 3.0 devices below:
1.Flash Disk or Hard Disk for network sharing. 2.Printer (It will be supported by future firmware upgrade) Gigabit LAN port
(1-4) Connect Ethernet devices, such as computers, switches and hubs. Gigabit WAN port (1) Console Port (1) One auto MDI/MDIX WAN ports are the connection for the Ethernet cable to the cable or DSL modem. Used to access Command Line Interface (CLI) via RJ45-to-DB9 console Cable. Table 1: DBG-X1000 Front Panel Descriptions Link Speed TX/RX Status Figure 2. Ethernet RJ-45 Port LEDs The device LEDs show information about current device status. When the device power up, the POWER/STATUS LED will show solid orange during power on process. Startup takes one minute approximately to complete, the LED will change to solid green. If you want to turn the device off and on again, we recommend you wait a few seconds between shutting it down and powering it back. The Ethernet LEDs show the status of each Ethernet port. Table 2 lists the name, color, status and description of each device LED. LED Indicators Power Color Status Description Orange/
Green Solid Orange Device during power-on process Solid Green Completion of power on Light Off The device is power-off Cloud Orange/
Green Solid Orange Cloud Connecting Solid Green Cloud Connected Green Light Off No Link. TX/RX Status LINK Speed Green/
Orange Solid Green Link present. Blinking Green Light Off Port is sending or receiving data. Port is operating at 10Mbps. Solid Green Port is operating at 100Mbps Solid Orange Port is operating at 1000Mbps Table 2: Device Status LED Descriptions A C D E B Figure 1. DBG-X1000 Front Panel 2 D-Link Nuclias Cloud-Managed Wireless VPN Gateway ENGLISH back panel of the device. Note: We recommend using a surge protector for the power connection. To power on the DBG-X1000 device, press the DC power switch on the rear panel to the on position. To power off the device, press the power switch to the off position. Connecting the Device to a Network This section provides basic information about physically connecting the DBG-X1000 to a network. To connect the necessary cables as shown in Figure 3. 1. Connect an RJ-45 cable from the port labeled WAN to the external router. The port WAN is pre-allocated to the WAN network segment. 2. Connect an RJ-45 cable from the port labeled LAN (1-8) to a switch in the LAN network segment. 3. Connect an RJ45-to-DB9 cable from the console port for CLI (Command Line Interface) management access. Internet WAN Switch LAN Console User Figure 3. Basic Cabling Example DBG-X1000 Default Interface Settings Ethernet Interface Interface Type IP Address Web-Based Management DHCP Client Static IP 192.168.10.1 Enabled Enabled 0.0.0.0 Disabled Disabled LAN(1-4) /
WLAN WAN DHCP Client Table 3: Default Interface Settings Note: DBG-X1000 allows Web GUI access from LAN and Wireless interfaces by default for security reason. Installing and Connecting the Device This chapter describes how to connect cables and power to the device. Before You Begin Observe the following precautions to help prevent shutdowns, equipment failures and injuries:
- Before installation, always check that the power supply is disconnected
- Ensure that the room in which you operate the device has adequate air circulation and that the room temperature does Not exceed 40C
(104F)
- Allow 1 meter (3 feet) of clear space to the front and back of the device.
- Do not place the device in an equipment rack frame that blocks the air vents on the sides of the chassis. Ensure that enclosed racks have fans and louvered sides.
- Correct these hazardous conditions before any installation: moist or wet floors, leaks, ungrounded or frayed power cables, or missing safety grounds. Connecting Power and Turn the Device On/Off The AC/DC Power Adapter shipped with the device connects the device to earth ground when plugged an AC grounding-type power outlet. The device must be connected to earth ground during normal operation. To connect power to the device, plug the AC/DC power adapter into the DC power phone jet on the D-Link Nuclias Cloud-Managed Wireless VPN Gateway 3 ENGLISH Initially Configure the Device The software is preinstalled on the DBG-X1000 device. When the device is powered on, it is ready to be configured. While the device has a default factory configuration that allow you to initially connect to the device, you must perform further configuration for your specific network require-
ments. Using the WebUI To use the WebUI, the workstation from which you are managing the device must initially be on the same subnetwork as the device. To access the device with the WebUI:
1. Connect your workstation on the port labeled LAN (1-4), which is pre-allocated to the LAN. 2. Ensure your workstation is DHCP Client enabled or configured with a static IP address in the 192.168.10.0/24 subnet. Using a Console Connection
(RJ45-to-DB9 DCE) The DBG-X1000 provides an serial port that enables a connection to a computer or terminal for monitoring and configuring the device. This port is a RJ-45 connector, implemented as a data communication terminal equipment (DCE) connection. To use the console port connection, you need the following equipment:
1. A terminal or a computer with both a serial port and the ability to emulate a terminal. 2. A RJ45-to-DB9 RS-232 with female connector.
(Already included in packing list) 3. If your Laptop or PC doesnt have RS-232 connector, a converter is required. Note: DBG-X1000 does not come with RS-232 converter and these must be purchased separately. 3. Log on the device web interface the default log on information is:
To establish a console connection:
Username: admin Password: admin Figure 4. Authentication Message 1. Plug the RJ-45 connector of the supplied RJ45-to-DB9 cable directly to the console port on the device. 2. Connect the other end of the cable to a terminal or to the serial connector of a computer running terminal emulation software. Set the terminal emulation software as following:
Baud rate: 115200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None 3. When you have correctly set up the terminal, having previously followed the instructions in section Connecting Power and Turn the Device On/Off then switch on your device. The boot sequence appears in the terminal. 4. Once the boot sequence completes, the command prompt is displayed, the device is ready to be configured. Technical Support https://www.dlink.com/support 4 D-Link Nuclias Cloud-Managed Wireless VPN Gateway ENGLISH Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. Industry Canada statement This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two condi-
tions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. D-Link Nuclias Cloud-Managed Wireless VPN Gateway 5 Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
(iii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utili-
sation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie, selon le cas;
(iii) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 25cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 25 cm entre le radiateur et votre corps. 6 D-Link Nuclias Cloud-Managed Wireless VPN Gateway D-Link Nuclias Cloud-Managed Wireless VPN Gateway 7 Ver. 1.00 2021/09/17