all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 4.70 MiB | ||||
1 | Attestation Statements | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 4.70 MiB |
WIRELESS N 150 HOME ROUTER Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision 1.0 Date Description December 10, 2010 DIR-600 Revision B5 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Copyright 2010 by D-Link Systems, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc. D-Link DIR-600 User Manual i Table of Contents Table of Contents Preface.................................................................................. i Manual Revisions ........................................................................... i Trademarks ...................................................................................... i Product.Overview...............................................................1 Package Contents ......................................................................... 1 System Requirements ................................................................. 2 Features ............................................................................................ 3 Hardware Overview ..................................................................... 4 Connections ........................................................................... 4 LEDs ........................................................................................... 5 Installation..........................................................................6 Before you Begin ........................................................................... 6 Wireless Installation Considerations ...................................... 7 Wall Mounting Your Device....................................................... 8 Connect to Cable/DSL/Satellite Modem .............................. 9 Connect to Another Router ....................................................10 Getting Started ............................................................................12 Configuration....................................................................13 Web-based Configuration Utility ..........................................13 Setup ...............................................................................................14 Internet ...................................................................................14 Internet Connection Setup Wizard ...............................15 Manual Internet Connection Setup .............................22 Static IP ..............................................................................23 Dynamic IP (DHCP) ........................................................24 PPPoE (Username/Password) ....................................25 PPTP ....................................................................................27 L2TP ....................................................................................29 Russia PPTP (Dual Access) ...........................................31 Russia PPPoE (Dual Access) ........................................33 Wireless Settings .................................................................35 Manual Wireless Settings .................................................36 802.11n/b/g (2.4GHz) ...................................................36 Network Settings ................................................................37 Router Settings ...............................................................38 DHCP Server Settings ...................................................39 DHCP Reservation .........................................................40 Advanced ......................................................................................41 Virtual Server ........................................................................41 Port Forwarding ..................................................................43 Application Rules ................................................................44 QoS Engine............................................................................45 Network Filter.......................................................................46 Website Filter ........................................................................47 Firewall Settings ..................................................................48 Firewall Rules ...................................................................49 Routing ...................................................................................51 Advanced Wireless Settings ............................................52 802.11n/b/g (2.4GHz) ...................................................52 Wi-Fi Protected Setup (WPS) ..........................................53 D-Link DIR-600 User Manual ii Table of Contents Advanced Network ............................................................55 UPnP ...................................................................................55 Internet Ping Block ........................................................55 Internet Port Speed .......................................................55 Multicast Streams ..........................................................55 IPv6 ..........................................................................................56 Static IPv6 .........................................................................57 Link-local Only ................................................................58 Static IPv6 (Stateless) ....................................................59 Static IPv6 (Stateful) ......................................................60 Autoconfiguration(Stateless/DHCPv6) ..................61 Autoconfiguration(Stateless/DHCPv6)-
(Stateless) ..........................................................................62 Autoconfiguration(Stateless/DHCPv6)-
(Stateful) ............................................................................63 PPPoE .................................................................................64 IPv6 in IPv4 Tunnel ........................................................65 IPv6 in IPv4 Tunnel(Stateless) ....................................66 IPv6 in IPv4 Tunnel (Stateful) .....................................67 6to4 .....................................................................................68 6to4(Stateless) Autoconfiguration ..........................69 6to4(Stateful) (DHCPv6) Autoconfiguration ........70 6rd .......................................................................................71 IPv6 Routing .........................................................................72 Tools ................................................................................................73 Admin .....................................................................................73 Time .........................................................................................74 Email Settings ......................................................................75 System ....................................................................................76 Firmware ................................................................................77 Dynamic DNS .......................................................................78 System Check .......................................................................79 Schedules ..............................................................................80 Status ..............................................................................................81 Device Info ............................................................................81 Logs .........................................................................................82 Statistics .................................................................................83 Internet Sessions .................................................................84 Wireless ..................................................................................85 IPv6 ..........................................................................................86 Support ..........................................................................................87 Wireless.Security..............................................................88 What is WPA? ................................................................................88 Wireless Connection Setup Wizard ......................................89 Wireless Security Setup Wizard .............................................90 Add Wireless Device with WPS Wizard ................................92 Configure WEP .............................................................................93 Configure WPA/WPA2-Personal (PSK) .................................94 Configure WPA/WPA2-Enterprise (RADIUS) ......................95 Connect.to.a.Wireless.Network........................................96 Using Windows 7 ......................................................................96 Configure WPS .....................................................................99 Using Windows Vista ........................................................... 103 Configure Wireless Security ......................................... 104 Using Windows XP ................................................................. 106 D-Link DIR-600 User Manual iii Table of Contents Configure WPA-PSK ......................................................... 107 Troubleshooting.............................................................109 Wireless.Basics................................................................113 What is Wireless? ...................................................................... 114 Tips ................................................................................................ 116 Wireless Modes ......................................................................... 117 Networking.Basics..........................................................118 Check your IP address ............................................................ 118 Statically Assign an IP address ............................................ 119 Technical.Specifications.................................................120 D-Link DIR-600 User Manual iv Section 1 - Product Overview Product Overview Package Contents DIR-600 Wireless N 150 Home Router Power Adapter Ethernet Cable CD-ROM c o p y r i g h t 2 0 0 9 D
L i n k
, a l l r i g h t s r e s e r v e d
. D
L i n k a n L L A T S S L - Q UIC K I N A U N A M G U I D E - ADOBE READER - U T A R T HERE TILIT Y S O F T W A R E u e
. k n i l d w. w w s. er old e h WIRELESS N QUADBAND HOME ROUTER DIR-815 ver1.00(E) d th e D
-Lin k logo are registered trademarks of the D-Link Corporation. A l s o r r e e m a r k r a d t o t h e r l gistere d trade m arks are the property of their respectiv Note: Using a power supply with a different voltage rating than the one included with the DIR-600 will cause damage and void the warranty for this product. D-Link DIR-600 User Manual 1 Section 1 - Product Overview System Requirements Network Requirements An Ethernet-based Cable or DSL modem IEEE 802.11n or 802.11g wireless clients 10/100 Ethernet Computer with the following:
Windows, Macintosh, or Linux-based operating system An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements:
Internet Explorer 6 or higher Firefox 3.0 or higher Safari 3.0 or higher Chrome 2.0 or higher Windows Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version. CD Installation Wizard Requirements Computer with the following:
Windows 7/ Vista / XP with Service Pack 3 An installed Ethernet adapter CD-ROM drive D-Link DIR-600 User Manual 2 Section 1 - Product Overview Features
(CUVGT9KTGNGUU0GVYQTMKPI6JG&+4RTQXKFGUWRVQ/DRUYKTGNGUUEQPPGEVKQPYKVJQVJGT
PYKTGNGUUENKGPVU6JKUECRCDKNKV[CNNQYUWUGTUVQRCTVKEKRCVGKPTGCNVKOGCEVKXKVKGUQPNKPGUWEJCU
XKFGQUVTGCOKPIQPNKPGICOKPICPFTGCNVKOGCWFKQ
%QORCVKDNGYKVJDCPFI&GXKEGU6JG&+4KUUVKNNHWNN[EQORCVKDNGYKVJVJG+'''
DCPF+'''IUVCPFCTFUQKVECPEQPPGEVYKVJGZKUVKPIDCPF+'''I2%+
75$CPF%CTFDWUCFCRVGTU
#FXCPEGF(KTGYCNN(GCVWTGU6JG9GDDCUGFWUGTKPVGTHCEGFKURNC[UCPWODGTQHCFXCPEGFPGVYQTM
OCPCIGOGPVHGCVWTGUKPENWFKPI
%QPVGPV(KNVGTKPI'CUKN[CRRNKGFEQPVGPVNVGTKPIDCUGFQP/#%#FFTGUU74.CPFQT
&QOCKP0COG
(KNVGT5EJGFWNKPI6JGUGNVGTUECPDGUEJGFWNGFVQDGCEVKXGQPEGTVCKPFC[UQTHQTC
FWTCVKQPQHJQWTUQTOKPWVGU
5GEWTG/WNVKRNG%QPEWTTGPV5GUUKQPU6JG&+4ECPRCUUVJTQWIJ820UGUUKQPU+V
UWRRQTVUOWNVKRNGCPFEQPEWTTGPV+25GECPF2262UGUUKQPUUQWUGTUDGJKPFVJG&+4
ECPUGEWTGN[CEEGUUEQTRQTCVGPGVYQTMU
7UGTHTKGPFN[5GVWR9K\CTF6JTQWIJKVUGCU[VQWUG9GDDCUGFWUGTKPVGTHCEGVJG&+4NGVU[QW
EQPVTQNYJCVKPHQTOCVKQPKUCEEGUUKDNGVQVJQUGQPVJGYKTGNGUUPGVYQTMYJGVJGTHTQOVJG+PVGTPGVQTHTQO
[QWTEQORCP[UUGTXGT%QPIWTG[QWTTQWVGTVQ[QWTURGEKEUGVVKPIUYKVJKPOKPWVGU
/CZKOWOYKTGNGUUUKIPCNTCVGFGTKXGFHTQO+'''5VCPFCTFICPF&TCHVPURGEKECVKQPU#EVWCNFCVCVJTQWIJRWVYKNNXCT[0GVYQTMEQPFKVKQPUCPF
GPXKTQPOGPVCNHCEVQTUKPENWFKPIXQNWOGQHPGVYQTMVTCHEDWKNFKPIOCVGTKCNUCPFEQPUVTWEVKQPCPFPGVYQTMQXGTJGCFNQYGTCEVWCNFCVCVJTQWIJRWVTCVG'PXKTQPOGPVCN
EQPFKVKQPUYKNNCFXGTUGN[CHHGEVYKTGNGUUUKIPCNTCPIG
D-Link DIR-600 User Manual 3 Section 1 - Product Overview Hardware Overview Connections Pressing the Reset Button restores the router to its original factory default settings. Receptor for the Power Adapter. LAN Ports Connect Ethernet devices such as computers, switches, and hubs. The Auto MDI/MDIX WAN port is the connection for the Ethernet cable to the Cable or DSL modem. D-Link DIR-600 User Manual 4 Section 1 - Product Overview Hardware Overview LEDs INTERNET A solid light indicates connection on the WAN port. This LED blinks during data transmission. WLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission. Power LED A solid light indicates a proper connection to the power supply. Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. D-Link DIR-600 User Manual 5 Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin Please configure the router with the computer that was last connected directly to your modem. You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet. When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the Internet and online or the wizard will not work. If you have disconnected any hardware, re-
connect your computer back to the modem and make sure you are online. D-Link DIR-600 User Manual 6 Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -
each wall or ceiling can reduce your adapters range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal. 4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise. 5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use. D-Link DIR-600 User Manual 7 Section 2 - Installation Wall Mounting Your Device You can mount the DIR-600 to a wall or a partition for easy and convenient placement of your device. To wall mount your device, A. Screw the provided screws with the equipment to the wall or partition where the device to be placed. B. Place the mounting holes on the bottom of the device over the screws to mount it to the wall or partition. C. Connect your cables to the device. Step A Step B Step C D-Link DIR-600 User Manual 8 Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Unplug the modems power adapter. Shut down your computer. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer. 5. Plug in your modem. Wait for the modem to boot (about 30 seconds). 6. Plug the power adapter to the router and connect to an outlet or power strip. 7. Use the power switch to power on the router. Wait about 30 seconds for the router to boot. 8. Turn on your computer. 9. Refer to Getting Started on page 12 to configure your router. D-Link DIR-600 User Manual 9 Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network:
Disable UPnP Disable DHCP Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below:
1. Plug the power into the router and use the power switch to power up the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer. 2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to Admin and leave the password box empty. Click Log In to continue. 3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue. 4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server checkbox. Click Save Settings to continue. 5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computers IP settings back to the original values as in Step 1. D-Link DIR-600 User Manual 10 Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network. D-Link DIR-600 User Manual 11 Section 2 - Installation Getting Started The DIR-600 includes a Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows XP. The steps and screens are similar for the other Windows operating systems. If the CD Autorun function does not automatically start on your computer, go to Start > Run. In the run box type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive). When the autorun screen appears, click Install. Note: It is recommended to write down the SSID and Security Key, followed by the login password. D-Link DIR-600 User Manual 12 Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router
(192.168.0.1). Enter Admin in the User Name field. Leave the password blank by default. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance. D-Link DIR-600 User Manual 13 Section 3 - Configuration Setup Internet This section allows you to configure your Routers Internet settings. Internet Connection Setup Wizard:
The Internet Connection Setup Wizard provides a quick method for configuring your Internet settings. To start the Internet Connection Setup Wizard, click the Internet Connection Setup Wizard button. Refer to Internet Connection Setup Wizard on page 15 for more information on how to use the Internet Connection Setup Wizard. Manual Internet Connection Option:
Click the Manual Internet Connection Setup button if you want to enter your Internet settings without running the Internet Connection Setup Wizard. Refer to Manual Internet Connection Setup on page 22 for more information on how to configure your Internet settings manually. D-Link DIR-600 User Manual 14 Section 3 - Configuration Internet Connection Setup Wizard Click the Internet Connection Setup Wizard button to start the Internet Connection Setup Wizard. D-Link DIR-600 User Manual 15 Section 3 - Configuration The following window appears, summarizing the steps required to complete the Internet Connection Setup Wizard:
Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue. D-Link DIR-600 User Manual 16 Section 3 - Configuration Select the type of Internet connection you use and then click Next to continue. If you selected DHCP Connection (Dynamic IP Address), you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PCs MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed. D-Link DIR-600 User Manual 17 Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. If your ISP requires you to enter a PPPoE service name, enter the service name in the Service Name field. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected PPTP, enter your PPTP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and PPTP server addresses. Click Next to continue. D-Link DIR-600 User Manual 18 Section 3 - Configuration If you selected L2TP, enter your L2TP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and L2TP server addresses. Click Next to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue. D-Link DIR-600 User Manual 19 Section 3 - Configuration If you selected Russia PPTP (Dual Access), enter your PPTP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click Next to continue. If you selected Russia PPPoE (Dual Access), enter your PPPoE username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. If your ISP requires you to manually specify the WAN Physical IP settings, click the Static IP radio button and enter the required IP Address, Subnet Mask, Gateway, and DNS Server Addresses in their respective fields. Click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. D-Link DIR-600 User Manual 20 Section 3 - Configuration Click Connect to save your settings. The following window appears to indicate that the settings are being saved. When the Router has finished saving all the changes, the Setup> Internet window will open. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet. D-Link DIR-600 User Manual 21 Section 3 - Configuration Manual Internet Connection Setup Access Point Mode:
Check the Enabled Access Point Mode box if you want to disable NAT on the router and turn it into an Access Point. Internet Connection Type:
Use the My Internet Connection is drop-down menu to select the mode that the router should use to connect to the Internet. D-Link DIR-600 User Manual 22 Section 3 - Configuration Manual Internet Connection Setup Static IP Select Static IP from the drop-down menu if all the Internet ports IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. IP Address:
Enter the IP address assigned by your ISP. Subnet Mask:
Enter the Subnet Mask assigned by your ISP. Default Gateway:
Enter the Gateway assigned by your ISP. DNS Servers:
The DNS server information will be supplied by your ISP
(Internet Service Provider). MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 23 Section 3 - Configuration Manual Internet Connection Setup Dynamic IP (DHCP) Select Dynamic IP (DHCP) from the drop-down menu to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox. Host Name:
The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure. Primary/
Secondary DNS Server:
Enter the Primary and Secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically from your ISP. Enter the value 0.0.0.0 if you did not specifically receive these from your ISP. MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 24 Section 3 - Configuration Manual Internet Connection Setup PPPoE (Username/Password) Select PPPoE (Username/Password) from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. Address Mode:
Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. IP Address:
Enter the IP address (Static PPPoE only). User Name:
Enter your PPPoE user name. Password:
Enter your PPPoE password and then retype the password in the next box. Service Name:
Enter the ISP Service Name (optional). Reconnect Mode:
Use the radio buttons to specify the reconnect mode. The user can specify a custom schedule or specify the On Demand, or Manual option. To specify a custom schedule, use the drop-down menu to select one of the schedules that has been defined in the Tools> Schedules window. To create a new schedule, click the New Schedule button to open the Tools> Schedules window. Refer to Schedules on page 80 for more information. Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. DNS Servers:
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only). D-Link DIR-600 User Manual 25 Section 3 - Configuration MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 26 Section 3 - Configuration Manual Internet Connection Setup PPTP Select PPTP (Point-to-Point Tunneling Protocol) from the drop-down menu if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode:
Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. PPTP IP Address:
Enter the IP address (Static PPTP only). PPTP Subnet Mask:
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only). PPTP Gateway IP Address:
PPTP Server IP Address:
Enter the Gateway IP Address provided by your ISP. Enter the Server IP provided by your ISP (optional). Username:
Enter your PPTP username. Password:
Enter your PPTP password and then retype the password in the next box. Reconnect Mode:
Use the radio buttons to specify the reconnect mode. The user can specify a custom schedule or specify the On Demand, or Manual option. To specify a custom schedule, use the drop-down menu to select one of the schedules that has been defined in the Tools> Schedules window. To create a new schedule, click the New Schedule button to open the Tools> Schedules window. Refer to Schedules on page 82 for more information. D-Link DIR-600 User Manual 27 Section 3 - Configuration Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. DNS Servers:
The DNS server information will be supplied by your ISP (Internet Service Provider). MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 28 Section 3 - Configuration Manual Internet Connection Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode:
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. L2TP IP Address:
Enter the L2TP IP address supplied by your ISP (Static only). L2TP Subnet Mask:
L2TP Gateway IP Address:
L2TP Server IP Address:
Enter the Subnet Mask supplied by your ISP (Static only). Enter the Gateway IP Address provided by your ISP. Enter the Server IP provided by your ISP (optional). Username:
Enter your L2TP username. Password:
Enter your L2TP password and then retype the password in the next box. Reconnect Mode:
Use the radio buttons to specify the reconnect mode. The user can specify a custom schedule or specify the On Demand, or Manual option. To specify a custom schedule, use the drop-down menu to select one of the schedules that has been defined in the Tools>
Schedules window. To create a new schedule, click the New Schedule button to open the Tools> Schedules window. Refer to Schedules on page 80 for more information. D-Link DIR-600 User Manual 29 Section 3 - Configuration Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. DNS Servers:
Enter the Primary and Secondary DNS Server Addresses (Static L2TP only). MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 30 Section 3 - Configuration Manual Internet Connection Setup Russia PPTP (Dual Access) Select PPTP (Point-to-Point Tunneling Protocol) from the drop-down menu if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode:
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. PPTP IP Address:
Enter the IP address (Static PPTP only). PPTP Subnet Mask:
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only). PPTP Gateway:
Enter the Gateway IP Address provided by your ISP. PPTP Server IP:
Enter the Server IP provided by your ISP (optional). Username:
Enter your PPTP username. Password:
Reconnect Mode:
Enter your PPTP password and then retype the password in the next box. Use the radio buttons to specify the reconnect mode. The user can specify a custom schedule or specify the On Demand, or Manual option. To specify a custom schedule, use the drop-down menu to select one of the schedules that has been defined in the Tools> Schedules window. To create a new schedule, click the New Schedule button to open the Tools> Schedules window. Refer to Schedules on page 80 for more information. D-Link DIR-600 User Manual 31 Section 3 - Configuration Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. DNS Servers:
The DNS server information will be supplied by your ISP (Internet Service Provider). MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 32 Section 3 - Configuration Manual Internet Connection Setup Russia PPPoE (Dual Access) Select PPPoE (Username/Password) from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. Address Mode:
Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. IP Address:
Enter the IP address (Static PPPoE only). User Name:
Enter your PPPoE user name. Password:
Enter your PPPoE password and then retype the password in the next box. Service Name:
Enter the ISP Service Name (optional). Reconnect Mode:
Use the radio buttons to specify the reconnect mode. The user can specify a custom schedule or specify the On Demand, or Manual option. To specify a custom schedule, use the drop-down menu to select one of the schedules that has been defined in the Tools> Schedules window. To create a new schedule, click the New Schedule button to open the Tools> Schedules window. Refer to Schedules on page 80 for more information. Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-
reconnect. DNS Addresses:
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only). D-Link DIR-600 User Manual 33 Section 3 - Configuration MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address:
The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. WAN Physical Settings:
If your ISP requires you to manually specify the WAN Physical IP settings, click the Static IP radio button and enter the required IP Address, Subnet Mask, Gateway, and DNS Server Addresses in their respective fields. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 34 Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to Wireless Connection Setup Wizard on page 89. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to Add Wireless Device with WPS Wizard on page 92. If you want to manually configure the wireless settings on your router click Manual Wireless Connection Setup and refer to the next page. D-Link DIR-600 User Manual 35 Section 3 - Configuration Manual Wireless Settings 802.11n/b/g (2.4GHz) Enable Wireless:
Schedule:
Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule. Wireless Network Name:
The Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. Enable Auto Channel Selection:
The Auto Channel Selection setting can be selected to allow the DIR-600 to choose the channel with the least amount of interference. Wireless Channel:
Indicates the channel setting for the DIR-600. By default the channel is set to 1. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Selection, this option will be greyed out. Transmission Rate:
Select the transmit rate. It is strongly suggested to select Best (Automatic) for best performance. WMM Enable:
WMM (Wi-Fi Multimedia) is QoS for your wireless network. Check this box to improve the quality of video and voice applications for your wireless clients. This feature is not available in 802.11n configurations. Enable Hidden Wireless Wireless Security Mode:
Check this box if you do not want the SSID of your wireless network to be broadcast by the DIR-600. If the SSID is hidden, the SSID of the DIR-600 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-600 in order to connect to it. Refer to Wireless Security on page 88 for more information regarding wireless security. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 36 Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router Settings:
Use this section to configure the Routers local network settings. DHCP Server Settings:
Use this section to configure the DIR-600s built-in DHCP server settings. DHCP Reservations List:
Displays information about the devices that have a DHCP reservation from the DIR-600. The information includes the Host Name, IP Address, MAC Address, and Expiration Time. Number of Dynamic DHCP Clients:
Displays information about the devices that have a dynamic DHCP lease from the DIR-600. The information includes the Host Name, IP Address, MAC Address, and Lease Expiration Time. DHCP Reservation:
Use this section to create a new DHCP reservation or manage existing DHCP reservations. D-Link DIR-600 User Manual 37 Section 3 - Configuration Network Settings Router Settings Router IP Address:
Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Mask:
Enter the Subnet Mask. The default subnet mask is 255.255.255.0. Host Name:
Enter a Host Name to identify the DIR-600. Local Domain:
Enter the Domain name (Optional). Enable DNS Relay:
Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 38 Section 3 - Configuration Network Settings DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-600 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to Obtain an IP Address Automatically. When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-600. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool. Enable DHCP Server:
Check this box to enable the DHCP server on your router. Uncheck to disable this function. DHCP IP Address Range:
Enter the starting and ending IP addresses for the DHCP servers IP assignment. Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. DHCP Lease Time:
The length of time for the IP address lease. Enter the Lease time in minutes. When you have finished configuring the new DHCP Server Settings, click the Save Settings button at the top or bottom of the window. D-Link DIR-600 User Manual 39 Section 3 - Configuration Network Settings DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Checkbox:
Check this box to enable the reservation. Computer Name:
Enter the computer name. Alternatively, select a computer that currently has a DHCP lease from the drop down menu and click << to automatically populate the Computer Name, IP Address, and MAC Address fields. IP Address:
Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range. MAC Address:
Enter the MAC address of the computer or device. When you have finished configuring the new DHCP Reservation, click the Save Settings button at the top or bottom of the window to activate your reservations. D-Link DIR-600 User Manual 40 Section 3 - Configuration Advanced Virtual Server The DIR-600 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-600 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-600 are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DIR-600 redirects the external service request to the appropriate server within the LAN network. The DIR-600 is also capable of port-redirection, meaning that incoming traffic to a particular port may be redirected to a different port on the server computer. For a list of ports for common applications, please visit http://support.dlink.com/faq/view.asp?prod_id=1191. D-Link DIR-600 User Manual 41 Section 3 - Configuration The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page. Enable Checkbox:
Check the box on the left side to enable the Virtual Server rule. Name:
Enter a name for the rule or select an application from the drop-down menu. Select an application and click
<< to populate the fields. IP Address:
Public Port/
Private Port:
Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the port that you want to open next to Public Port and Private Port. The public and private ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network. Traffic Type:
Select TCP, UDP, or All from the Protocol drop-down menu. Schedule Drop-Down Menu:
Use the drop-down menu to schedule the time that the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 42 Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Enable Checkbox:
Tick the checkbox on the left side to enable the Port Forwarding rule. Name:
Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address:
Public Port/
Private Port:
Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the port that you want to open next to Public Port and Private Port. The public and private ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network. Traffic Type:
Select TCP, UDP, or All from the drop-down menu. Schedule:
Use the drop-down menu to schedule the time that the Port Forwarding rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 43 Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-600. If you need to run applications that require multiple connections, specify the port normally associated with an application in the Trigger Port field, select the protocol type as TCP or UDP, then enter the firewall
(public) ports associated with the trigger port to open them for inbound traffic. Enable Checkbox:
Check the box on the left side to enable the Application Rule. Name:
Enter a name for the rule. You may select a pre-defined application from the Application drop-down menu and click <<. Trigger:
This is the port used to trigger the application. It can be either a single port or a range of ports. Traffic Type:
Select the protocol of the trigger port (TCP, UDP, or All). Firewall:
This is the port number on the Internet side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. Traffic Type:
Select the protocol of the firewall port (TCP, UDP, or All). Schedule:
The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 44 Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable QoS Engine:
This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP. Automatic Uplink Speed:
This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection. Measured Uplink Speed:
Manual Uplink Speed:
Connection Type:
Detected xDSL or Other Frame Relay Network:
This displays the detected uplink speed. The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISPs often define speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test your uplink speed with a service such as www.dslreports.com. By default, the router automatically determines whether the underlying connection is an xDSL/Frame-relay network or some other connection type (such as cable modem or Ethernet), and it displays the result as Detected xDSL or Frame Relay Network. If you have an unusual network connection in which you are actually connected via xDSL but for which you configure either Static or DHCP in the Internet settings, setting this option to xDSL or Other Frame Relay Network ensures that the router will recognize that it needs to shape traffic slightly differently in order to give the best performance. Choosing xDSL or Other Frame Relay Network causes the measured uplink speed to be reported slightly lower than before on such connections, but gives much better results. When Connection Type is set to auto-detect, the automatically detected connection type is displayed here. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 45 Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router. Configure MAC Filtering:
Select Turn MAC Filtering OFF, Turn MAC Filtering ON and ALLOW computers listed to access the network, or Turn MAC Filtering ON and DENY computers listed to access the network from the drop-down menu. Enable Checkbox:
Check the box on the left side to enable the Network Filter. MAC Address:
Enter the MAC address you would like to filter. To find the MAC address on a computer, please refer to the Networking Basics section in this manual. DHCP Client List:
Select a DHCP client from the Computer Name drop down menu and click << to copy that MAC Address. Schedule:
The schedule of time when the Network Filter will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. Click the New Schedule button to create your own times in the Tools > Schedules section. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 46 Section 3 - Configuration Website Filter Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select the appropriate Web Filtering option, enter the domain or website, and click Save Settings. Configure Web Filtering:
Select Turn OFF WEBSITE FILTERING, ALLOW computers access to ONLY these sites, or DENY computers access to ONLY these sites from the drop-down menu. Enable Checkbox:
Check the box on the left side to enable the Website Filter. Website URL:
Enter the keywords or URLs that you want to allow or block. Schedule:
The schedule of time when the Website Filter will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. Click the New Schedule button to create your own times in the Tools > Schedules section. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 47 Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The DIR-600 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world. Firewall Settings:
Check the Enable SPI box to enable the SPI (Stateful Packet Inspection, also known as dynamic packet filtering) feature. Enabling SPI helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. DMZ Host:
If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Carry out the following to create a DMZ host:
1. Check the Enable DMZ box. 2. Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication in the DMZ IP address field. To specify an existing DHCP client, use the Computer Name drop-down to select the computer that you want to make a DMZ host. If selecting a computer that is a DHCP client, be sure to make a static reservation in the Setup > Network Settings page so that the IP address of the DMZ machine does not change. 3. Click the Save Settings button to add the new DMZ host. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. D-Link DIR-600 User Manual 48 Section 3 - Configuration Firewall Settings Firewall Rules Use the Firewall Rules section to create/modify firewall rules. Enable Checkbox:
Check the box on the left side to enable the firewall rule. Name:
Enter a name to identify the firewall rule. Action:
Use the drop-down menu to Allow or Deny transport of the data packets according to the criteria defined in the firewall rule. Source:
Use the Source drop-down menu to specify the interface that connects to the source IP addresses of the firewall rule. Enter the first source IP address in the range in the adjacent top IP Address field. Enter the last source IP address in the range in the IP Address field below. Dest:
Use the Dest drop-down menu to specify the interface that connects to the destination IP addresses of the firewall rule. Enter the first destination IP address in the range in the adjacent top IP Address field. Enter the last destination IP address in the range in the IP Address field below. D-Link DIR-600 User Manual 49 Section 3 - Configuration Protocol:
Select the protocol of the firewall port (All, TCP, UDP, or ICMP). Port Range:
Enter the first port of the range that will be used for the firewall rule in the top port range field and enter the last port in the field underneath. Select Schedule:
Use the drop-down menu to schedule the time that the Firewall rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. Click the New Schedule button to create your own times in the Tools > Schedules section. When you have finished configuring the firewall rules, click the Save Settings button at the top or bottom of the window to save any changes made. D-Link DIR-600 User Manual 50 Section 3 - Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. Enable:
To enable a route, check the box that is on the left side of the route. Interface:
Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router. Destination:
Enter the IP address of the packets that will take this route. Subnet Mask:
Enter the subnet mask to specify the subnet of the IP packets that will take this route. Gateway:
Enter the next hop that will be taken if this route is used. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 51 Section 3 - Configuration Advanced Wireless Settings 802.11n/b/g (2.4GHz) Transmit Power:
Set the transmit power of the antennas. Beacon Period:
Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold:
This value should remain at its default setting of 2346. If inconsistent data flow is a problem, only a minor modification should be made. Fragmentation:
The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. DTIM Interval:
(Delivery Traffic Indication Message) 1 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. Preamble Type:
Use the radio buttons to specify whether the Router should use the Short Preamble or Long Preamble type. The preamble type defines the length of the CRC (Cyclic Redundancy Check) block for communication between the Router and roaming wireless adapters. Wireless Mode:
Use the drop-down menu to specify the wireless mode that will be used by the 2.4GHz band. The available options are 802.11n only, 802.11 Mixed (g/b), and 802.11 Mixed (n/g/b). Band Width:
Use the drop-down menu to select the channel bandwidth. If you selected the 802.11 Mixed (g/b) or 802.11 Mixed (n/g/b) wireless mode, the available options are 20 MHz and 20/40MHz. If selecting the 802.11n only wireless mode, 20MHz is the only available option. Short Guard Interval:
Check this box to reduce the guard interval time therefore increasing the data capacity. However, its less reliable and may create higher data loss. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 52 Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the Initial setup as well as the Add New Device processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method. The time reduction in setup and ease of use are quite beneficial, while the highest wireless Security setting of WPA2 is automatically used. Enable:
Enable the Wi-Fi Protected Setup feature. PIN Settings:
PIN:
Reset PIN to Default:
A PIN is a unique number that can be used to add the router to an existing network or to create a new network. The default PIN may be printed on the bottom of the router. For extra security, a new PIN can be generated. You can restore the default PIN at any time. Only the Administrator (admin account) can change or reset the PIN. Shows the current value of the routers PIN. Click this button to restore the default PIN of the router. Generate New PIN:
Click this button to create a random number that is a valid PIN. This becomes the routers PIN. You can then copy this PIN to the user interface of the registrar. D-Link DIR-600 User Manual 53 Section 3 - Configuration Add Wireless Station:
Click the Connect your Wireless Device button to start Wireless Connection Setup Wizard. This wizard helps you add wireless devices to the wireless network. The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device. If the device supports Wi-Fi Protected Setup and has a configuration button, you can add it to the network by pressing the configuration button on the device and then the on the router within 60 seconds. The status LED on the router will flash three times if the device has been successfully added to the network. There are several ways to add a wireless device to your network. A registrar controls access to the wireless network. A registrar only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 54 Section 3 - Configuration Advanced Network Enable UPnP:
To use the Universal Plug and Play (UPnP) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. Enable WAN Ping Response:
Unchecking the box will not allow the DIR-600 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be pinged. WAN Port Speed:
You may set the port speed of the Internet port to 10Mbps, 100Mbps, or auto. Some older cable or DSL modems may require you to set the port speed to 10Mbps. Enable Multicast Streams:
Check the Enable Multicast Streams box to allow multicast traffic to pass through the router from the Internet. Wireless Enhance Mode:
Check the Wireless Enhance Mode box to enable the router to forward all multicast streams from the Internet to the wireless station using a unicast stream. This feature helps improve the quality of multimedia applications for wireless users. Click the Save Settings button to save any changes made. UPnP Internet Ping Block Internet Port Speed Multicast Streams D-Link DIR-600 User Manual 55 Section 3 - Configuration IPv6 Use the IPv6 window to configure the mode that the Router will use to access an IPv6 Internet connection. My Internet Connection is:
Use the drop-down menu to select the IPv6 Internet Connection mode. D-Link DIR-600 User Manual 56 Section 3 - Configuration IPv6 Static IPv6 Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. WAN IPv6 Address Settings:
Enter the address settings supplied by your Internet provider (ISP). LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-Local Address:
LAN Address Autoconfiguration Settings:
Displays the Routers LAN Link-Local Address. Use this section to configure the IPv6 autoconfiguration settings. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 57 Section 3 - Configuration IPv6 Link-local Only Select Link-local Only from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 link local method to connect to the Internet. LAN IPv6 Address Settings:
Displays the LAN IPv6 Link-Local address of the router. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 58 Section 3 - Configuration IPv6 Static IPv6 (Stateless) To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement Lifetime:
Check to enable the Autoconfiguration feature. Select the Stateless option from the drop-down menu. Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 59 Section 3 - Configuration IPv6 Static IPv6 (Stateful) To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Check to enable the Autoconfiguration feature. Autoconfiguration Type:
Select the Stateful(DHCPv6) option from the drop-down menu. IPv6 Address Range Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime:
Enter the IPv6 Address Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 60 Section 3 - Configuration IPv6 Autoconfiguration(Stateless/DHCPv6) Select Autoconfiguration(Stateless/DHCPv6) from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 Autoconfiguration(Stateless/DHCPv6) method to connect to the Internet. IPv6 DNS Settings:
Select either Obtain DNS server address automatically or Use thefollowing DNS Address. Enable DHCP-PD:
Select DHCP-PD to acquire the IPv6 prefix for the Router. LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-Local Address:
Displays the Routers LAN Link-Local Address. LAN Address Autoconfiguration Settings:
Use this section to configure the IPv6 autoconfiguration settings. D-Link DIR-600 User Manual 61 Section 3 - Configuration Autoconfiguration(Stateless/DHCPv6)- (Stateless) IPv6 To configure the Router to use a 6rd Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement Lifetime:
Check to enable the Autoconfiguration feature. Select the Stateless option from the drop-down menu. Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 62 Section 3 - Configuration Autoconfiguration(Stateless/DHCPv6)- (Stateful) IPv6 To configure the Router to use a 6rd Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type:
Check to enable the Autoconfiguration feature. Select Stateful. Refer to the previous page for Stateful. IPv6 Address Range
(Start):
Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range
(End):
Enter the end IPv6 Address for the DHCPv6 range for your local computers. Router Advertisement Lifetime:
Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 63 Section 3 - Configuration IPv6 PPPoE Select PPPoE from the My IPv6 Connection is drop-down menu if your Router will use the PPPoE method to connect to the Internet. PPPoE:
Enter the settings supplied by your Internet provider (ISP). IPv6 DNS Settings:
Enable DHCP-PD:
Select either Obtain DNS server address automatically or Use thefollowing DNS Address. Select DHCP-PD to acquire the IPv6 prefix for the Router. LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-Local Address:
LAN Address Autoconfiguration Settings:
Displays the Routers LAN Link-Local Address. Use this section to configure the IPv6 autoconfiguration settings. D-Link DIR-600 User Manual 64 Section 3 - Configuration IPv6 IPv6 in IPv4 Tunnel Select 6rd from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 6rd method to connect to the Internet. IPv6 in IPv4 Tunnel Settings:
Enter the settings supplied by your Internet provider (ISP). IPv6 DNS Settings:
LAN IPv6 Address:
Select either Obtain DNS server address automatically or Use thefollowing DNS Address. Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-Local Address:
LAN Address Autoconfiguration Settings:
Displays the Routers LAN Link-Local Address. Use this section to configure the IPv6 autoconfiguration settings. D-Link DIR-600 User Manual 65 Section 3 - Configuration IPv6 IPv6 in IPv4 Tunnel(Stateless) To configure the Router to use a 6rd Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement Lifetime:
Check to enable the Autoconfiguration feature. Select the Stateless option from the drop-down menu. Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 66 Section 3 - Configuration IPv6 IPv6 in IPv4 Tunnel (Stateful) To configure the Router to use a 6rd Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type :
IPv6 Address Range
(Start) :
IPv6 Address Range
(End) :
Router Advertisement Lifetime :
Check to enable the Autoconfiguration feature. Select Stateful. Refer to the previous page for Stateful. Enter the start IPv6 Address for the DHCPv6 range for your local computers. Enter the end IPv6 Address for the DHCPv6 range for your local computers. Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 67 Section 3 - Configuration IPv6 6to4 Select 6to4 from the My IPv6 Connection is drop-down menu if your Router will use an IPv6 to IPv4 tunnel to connect to the Internet. WAN IPv6 Address Settings:
Enter the address settings supplied by your Internet provider (ISP). LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-
Local Address:
LAN Address Autoconfiguration Settings:
Displays the Routers LAN Link-Local Address. Use this section to congure the IPv6 autoconguration settings. D-Link DIR-600 User Manual 68 Section 3 - Configuration IPv6 6to4(Stateless) Autoconfiguration To configure the Router to use an IPv6 to IPv4 tunnel stateless autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Autoconfiguration Type:
Router Advertisement Lifetime:
Check to enable the Autoconfiguration feature. Select the Stateless option from the drop-down menu. Enter the Router Advertisement Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 69 Section 3 - Configuration 6to4(Stateful) (DHCPv6) Autoconfiguration IPv6 To configure the Router to use an IPv6 to IPv4 tunnel stateful autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below:
Enable Autoconfiguration:
Check to enable the Autoconfiguration feature. Autoconfiguration Type:
Select the Stateful(DHCPv6) option from the drop-down menu. IPv6 Address Range Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Range End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address Lifetime:
Enter the IPv6 Address Lifetime (in minutes). Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 70 Section 3 - Configuration IPv6 6rd Select 6rd from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 6rd method to connect to the Internet. WAN IPv6 Address Settings:
Enter the address settings supplied by your Internet provider (ISP). LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-Local Address:
LAN Address Autoconfiguration Settings:
Displays the Routers LAN Link-Local Address. Use this section to configure the IPv6 autoconfiguration settings. D-Link DIR-600 User Manual 71 Section 3 - Configuration The Routing option is an advanced method of customizing specific routes of data through your network. IPv6 Routing Enable:
Metric:
To enable a route, check the box that is on the left side of the route. Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router. Interface:
Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router. Destination IPv6
/ Prefix Length:
Enter the LAN (local) IPv6 address for the router and Prefix Length. Gateway:
Enter the next hop that will be taken if this route is used. D-Link DIR-600 User Manual 72 Section 3 - Configuration Tools Admin This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet. Admin Password:
Enter a new password for the Administrator Login Name. The administrator can make changes to the settings. Enable Graphical Authentication:
Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your routers network settings. Enable Remote Management:
Remote management allows the DIR-600 to be configured from the Internet by a web browser. A username and password is still required to access the Web-Management interface. In general, only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host. Remote Admin Port:
Enter the port number that will be used to access the DIR-815. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 73 Section 3 - Configuration Time The Time window allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone:
Select the Time Zone from the drop-down menu. Enable Daylight Saving:
Check this box if the country your are located in uses Daylight Saving time. Enter a start date and an end date for daylight saving time. Sync. Your Computers Time Settings:
Click this button to synchronize the DIR-600s system clock to your computers time settings. Automatic Time and Date Configuration:
NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. To enable NTP carry out the following:
1. Check the Automatically synchronize with D-Links Internet Time Server box. 2. Choose the D-Link NTP server that you would like to synchronize with from the NTP Server Used drop-down menu. 3. Click the Update Now button to update the time on the Router clock so that it is synchronized with the D-Link Internet Time Server. Set the Time and Date Manually:
Use this section to configure the time manually. To configure the time manually, use the drop-down menus to select the appropriate Year, Month, Day, Hour, Minute, and Second. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 74 Section 3 - Configuration Email Settings The Email feature can be used to send the system log files and router alert messages to your email address. From Email Address:
This email address will appear as the sender when you receive a log file or firmware upgrade notification via email. To Email Address:
Enter the email address where you want the email sent. Email Subject:
SMTP Server Address:
Enter the text that you want to appear in the subject line of the e-mail that is sent. Enter the SMTP server address for sending email. If your SMTP server requires authentication, select this option. Account Name:
Enter your account for sending email. Password:
Enter the password associated with the account. Re-type the password associated with the account. Send Mail Now:
Click this button to send a test email from the Router to verify that the email settings have been configured correctly. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 75 Section 3 - Configuration System This section allows you to manage the routers configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that youve created. Save Settings to Local Hard Drive:
Load Settings from Local Hard Drive:
Restore to Factory Default Settings:
Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. A file dialog will appear, allowing you to select a location and file name for the settings. Use this option to load previously saved router configuration settings. First, use the Browse option to find a previously saved file of configuration settings. Then, click the Upload Settings button below to transfer those settings to the router. This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save button above. Reboot Device:
Click to reboot the router. Clear Language Pack:
If you previously installed a language pack and want to revert all the menus on the Router interface back to the default language settings, click the Clear button. D-Link DIR-600 User Manual 76 Section 3 - Configuration Firmware Use the Firmware window to upgrade the firmware of the Router and install language packs. If you plan to install new firmware, make sure the firmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language pack available. Please check the D-Link support site for firmware updates at http://
support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. Firmware Information:
This section displays information about the firmware that is loaded on the Router. Click the Check Now button to find out if there is an updated firmware; if so, download the new firmware to your hard drive. Firmware Upgrade:
After you have downloaded the new firmware, click Browse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade. Language Pack Upgrade:
If you want to change the Routers language pack, click Browse to locate the language pack. Click Upload to complete the load the new language pack. D-Link DIR-600 User Manual 77 Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is. Enable DDNS:
Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. Check the box to enable DDNS. Server Address:
Choose your DDNS provider from the drop down menu. Host Name:
Enter the Host Name that you registered with your DDNS service provider. User Account:
Enter the Username for your DDNS account. Password:
Enter the Password for your DDNS account. DDNS Account Testing:
Click this button to verify that the DDNS account user name and password have been entered correctly. Click the Save Settings button to save any changes made. D-Link DIR-600 User Manual 78 Section 3 - Configuration System Check Ping Test:
The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Click Stop to stop sending Ping packets IPv6 Ping Test:
The IPv6 Ping Test is used to send IPv6 Ping packets to test if a computer is on the Internet. Enter the IPv6 Address that you wish to Ping, and click Ping. Click Stop to stop sending IPv6 Ping packets Ping Results:
The results of your Ping/IPv6 Ping attempts will be displayed here. D-Link DIR-600 User Manual 79 Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Name:
Enter a name for your new schedule. Days:
Select a day, a range of days, or All Week to include every day. Time:
Check All Day - 24hrs or enter a Start Time and End Time for your schedule. Add:
Click Add to save your schedule. You must click the Add button for your schedules to go into effect. Schedule Rules List:
The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule. D-Link DIR-600 User Manual 80 Section 3 - Configuration Status Device Info This page displays the current information for the DIR-600. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection. General:
Displays the routers time and firmware version. WAN:
Displays the MAC address and the public IP settings for the router. LAN:
Displays the MAC address and the private (local) IP settings for the router. Wireless LAN:
Displays the wireless MAC address and your wireless settings such as SSID and Channel. D-Link DIR-600 User Manual 81 Section 3 - Configuration Logs The router automatically logs (records) events of possible interest in its internal memory. If there isnt enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility. Save Log File:
Click the Save button save the Routers log entries to a log file on your computer. Log Type:
Use the radio buttons to select the types of messages that you want to display from the log. System, Firewall
& Security, and Router Status messages can be selected. Log Level:
There are three levels of message importance: Critical, Warning, and Information. Select the levels that you want displayed in the log. Log Files:
Use this section to view and manage the Routers log entries. First Page:
Click this button to view the first page of the Router logs. Last Page:
Click this button to view the last page of the Router logs. Previous:
Click this button to view the previous page of the Router logs. Next:
Click this button to view the next page of the Router logs. Clear:
Clears all of the log contents. Link to Log Settings:
Click this button to open the Tools > Email Settings screen so that you can change the Email configuration for sending logs. D-Link DIR-600 User Manual 82 Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-600 on both the WAN, LAN ports and the 802.11n/g (2.4GHz) wireless bands. The traffic counter will reset if the device is rebooted. Refresh:
Click the Refresh button to refresh the Routers traffic statistics. Reset:
Click the Reset button to reset the Routers traffic statistics. D-Link DIR-600 User Manual 83 Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer. D-Link DIR-600 User Manual 84 Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients. D-Link DIR-600 User Manual 85 Section 3 - Configuration IPv6 The IPv6 page displays a summary of the Routers IPv6 settings and lists the IPv6 address and host name of any IPv6 clients. D-Link DIR-600 User Manual 86 Section 3 - Configuration Support D-Link DIR-600 User Manual 87 Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-600 offers the following types of security:
WPA2 (Wi-Fi Protected Access 2) WPA (Wi-Fi Protected Access) WPA2-PSK (Pre-Shared Key) WPA-PSK (Pre-Shared Key) What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP:
Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys havent been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computers hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. D-Link DIR-600 User Manual 88 Section 4 - Security Wireless Connection Setup Wizard To run the Wireless Connection Setup Wizard, click the Wireless Connection Setup Wizard button in the Setup>Wireless Settings window. D-Link DIR-600 User Manual 89 Section 4 - Security Wireless Security Setup Wizard Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the routers network key and click Next. Manually: Select this option to manually enter your network key and click Next. If you selected Automatically, the summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings. D-Link DIR-600 User Manual 90 Section 4 - Security If you selected Manually, the following screen will appear. Enter the Wireless Security Password you would like to use for your wireless network and click Next to proceed to the next window. The summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings. D-Link DIR-600 User Manual 91 Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients. PIN: Select this option to use PIN method. In order to use this method you must know the wireless clients 8 digit PIN and click Connect. PBC: Select this option to use PBC (Push Button) method to add a wireless client. Click Connect. D-Link DIR-600 User Manual 92 Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3. Click the Manual Wireless Connection Setup button. 4. Next to Security Mode, select Enable WEP Wireless Security (basic). 5. Next to WEP Encryption, select 64bit or 128bit. 6. Next to Default WEP Key, select the WEP key you would like to use as the default WEP key. The available options are WEP Key 1, WEP Key 2, WEP Key 3, or WEP Key 4. 7. Enter the WEP key you would like to use in the WEP Key field. 8. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the router. D-Link DIR-600 User Manual 93 Section 4 - Security Configure WPA/WPA2-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3. Click the Manual Wireless Connection Setup button. 4. Next to Security Mode, select Enable WPA/WPA2 Wireless Security
(enhanced). 5. Next to Cipher Type, select Auto (TKIP/AES), TKIP, or AES. 6. Next to PSK/EAP, select PSK. 7. Enter the WPA network key you would like to use in the Network Key field. 8. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router. D-Link DIR-600 User Manual 94 Section 4 - Security Configure WPA/WPA2-Enterprise (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3. Click the Manual Wireless Connection Setup button. 4. Next to Security Mode, select Enable WPA/WPA2 Wireless Security
(enhanced). 5. Next to Cipher Type, select Auto (TKIP/AES), TKIP, or AES. 6. Next to PSK/EAP, select EAP. 7. Next to RADIUS Server IP Address enter the IP Address of your RADIUS server. 8. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port. 9. Next to Shared Secret, enter the security key. 10. Click Save Settings to save your settings. D-Link DIR-600 User Manual 95 Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). 2. The utility will display any available wireless networks in your area. Wireless Icon D-Link DIR-600 User Manual 96 Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router. D-Link DIR-600 User Manual 97 Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DIR-600 User Manual 98 Section 5 - Connecting to a Wireless Network Configure WPS The WPS feature of the router can be configured using Windows 7. Carry out the following steps to use Windows 7 to configure the WPS feature of the router:
1. Click the Start button and select Computer from the Start menu. 2. Click the Network option. D-Link DIR-600 User Manual 99 Section 5 - Connecting to a Wireless Network 3. Double-click the DIR-600. 4. Input the WPS PIN number (displayed in the WPS window on the Routers LCD screen or in the Setup.> Wireless.Setup menu in the Routers Web UI) and click Next. D-Link DIR-600 User Manual 100 Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue. D-Link DIR-600 User Manual 101 Section 5 - Connecting to a Wireless Network 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the DIR-600 has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup. D-Link DIR-600 User Manual 102 Section 5 - Connecting to a Wireless Network Using Windows Vista Windows Vista users may use the built-in wireless utility. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows Vista utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select Connect to a network. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-600 User Manual 103 Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DIR-600 User Manual 104 Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DIR-600 User Manual 105 Section 5 - Connecting to a Wireless Network Using Windows XP Windows XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows XP utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or Right-click on the wireless computer icon in your system tray (lower-
right corner next to the time). Select View Available Wireless Networks. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-600 User Manual 106 Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows XP Wireless Utility by right-clicking on the wireless computer icon in your system tray
(lower-right corner of screen). Select View Available Wireless Networks. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DIR-600 User Manual 107 Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router. D-Link DIR-600 User Manual 108 Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-600. Read the following descriptions if you are having problems. The examples below are illustrated in Windows XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples. 1. Why cant I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. Make sure you have an updated Java-enabled web browser. We recommend the following:
- Microsoft Internet Explorer 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google Chrome 2.0 and higher
- Apple Safari 3.0 and higher Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DIR-600 User Manual 109 Section 6 - Troubleshooting Configure your Internet settings:
Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times. Close your web browser (if open) and open it. Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your web management. If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty. D-Link DIR-600 User Manual 110 Section 6 - Troubleshooting 3. Why cant I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, youll have to do a special ping of the destination youre trying to go to. A destination could be another computer, or a URL. Click on Start and then click Run. Windows 95, 98, and Me users type in command (Windows NT, 2000, and XP users type in cmd) and press Enter (or click OK). Once the window opens, youll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472 D-Link DIR-600 User Manual 111 Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network were working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below:
Open your browser, enter the IP address of your router (192.168.0.1) and click OK. Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. Click on Setup and then click Manual Configure. To change the MTU enter the number in the MTU field and click Save Settings to save your settings. Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten. D-Link DIR-600 User Manual 112 Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. D-Link DIR-600 User Manual 113 Appendix A - Wireless Basics What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues. Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. D-Link DIR-600 User Manual 114 Appendix A - Wireless Basics Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesnt use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether its for home, office, business, D-Link has a wireless solution for it. Home Gives everyone at home broadband access Surf the web, check email, instant message, etc. Gets rid of the cables around the house Simple and easy to use Stay on top of everything at home as you would at office Remotely access your office network from home Share Internet connection and printer with multiple computers No need to dedicate office space Small Office and Home Office D-Link DIR-600 User Manual 115 Appendix A - Wireless Basics Where is wireless used?
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and its becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called hotspots. Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if youre installing it for the first time it could be quite a task not knowing where to start. Thats why weve put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. Security Dont let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. D-Link DIR-600 User Manual 116 Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking:
Infrastructure All wireless clients will connect to an access point or wireless router. Ad-Hoc Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-600 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DIR-600 User Manual 117 Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows 7/Vista users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. D-Link DIR-600 User Manual 118 Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step.1 Windows.7.- Click on Start > Control.Panel > Network.and.Internet > Network.and.Sharing.Center > Change.Adapter. Setting.. Windows.Vista - Click on Start > Control.Panel > Network.and.Internet > Network.and.Sharing.Center > Manage.Network. Connections. Windows.XP - Click on Start > Control.Panel > Network.Connections. Windows.2000 - From the desktop, right-click My.Network.Places > Properties. Step.2 Right-click on the Local.Area.Connection which represents your network adapter and select Properties. Step.3 Highlight Internet.Protocol.(TCP/IP) and click Properties. Step.4 Click Use.the.following.IP.address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the routers LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router
(192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step.5 Click OK twice to save your settings. D-Link DIR-600 User Manual 119
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2011-01-27 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2011-01-27
|
||||
1 | Applicant's complete, legal business name |
D-Link Corporation
|
||||
1 | FCC Registration Number (FRN) |
0007371172
|
||||
1 | Physical Address |
17595 Mt. Herrmann
|
||||
1 |
Fountain Valley, California 92708
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
KA2
|
||||
1 | Equipment Product Code |
IR600B5
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B**** A******
|
||||
1 | Title |
General Counsel
|
||||
1 | Telephone Number |
714-8********
|
||||
1 | Fax Number |
866-7********
|
||||
1 |
b******@dlink.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
G****** C******
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
g******@tw.bureauveritas.com
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
W**** L********
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
w******@tw.bureauveritas.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | WIRELESS N 150 HOME ROUTER | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted. Device is a 1Tx1R 802.11bgn router as described in this filing. End-users and responsible parties must be provided with operating and installation instructions to ensure RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R**** C****
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.2880000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC