User Manual English TFT-LCD Color Monitor FS-L4201C www.tandberg.net Printed in Korea Part No. 942667020001 - 01 INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to crrent the interference by one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit difference from that to which the recerver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment Table of Contents Parts Connection to Signal Source Out Drawing of product Name and Function Power Management Feature Adjusting OSD Standard Signal Table Pin assignment table of signal connector Specification Troubleshooting Warning 3 4 6 7 8 10 12 13 15 16 18 Parts Connection to Signal Source Basic Connection 42 " LCD Monitor User's Manual This monitor do not provide any other accessaries and peripheral devices (ex,speaker and signal cable) because the Tandberg's reguest. AC Inlet. AC on/ off Switch RCA Coaxial S/PDIF Audio input 9 Pin D-Sub connector for Speaker Out 24 Pin DVI Connector for Digital TMDS 15 Pin D-Sub connector for Analog RGB LCD MONITOR 3 User s Manual LCD MONITOR 4 User s Manual
< Power source connection >
< Signal cable connection>
O ut Drawing of product D-Sub Analog(Data in) DVI Digital Coaxial S/PDIF Input Audio amp Output AC Inlet AC on/off swith 1. Use 220 V or 110 V. (Free Voltage) 2. Connect monitor and Signal Source via Signal cable 3. Power on the monitor and computer. 4. Connection is finished. LCD MONITOR 5 User s Manual LCD MONITOR 6 User s Manual Name and Function Power Management Feature Front side Rear side Power management system of this monitor can not be corresponded with VESA DPMS when the display video signal is none because the specific character of Tandberg system Status LED Sign Power Consumption Normal mode Green on Normal Power Stand by mode Red on 20W or Below Power indicating LED Remote signal window SOURCE BUTTON
- BUTTON
+ BUTTON BUTTON MENU BUTTON OK BUTTON BUTTON LCD MONITOR 7 User s Manual LCD MONITOR 8 User s Manual Functions Remote signal wirdow This window is for the receiving signal from remote controller Do not hide this window. Power Indicating LED Green : Normal mode RED : Standby mode On-Screen Display (OSD) Function Button MENU : With OSD deactivated, Activated to OSD menu With OSD activated, Exit from main menu or sub menu. OK : With OSD deactivated, you can see the kind of displayed source on the right bottom side of the screen. With OSD activated, Enter sub menu and change each sub menu item
: With OSD deactivated, Hot key of the brightness control and increases UP(
the brightness. With OSD activated, move the cursor upward.
: With OSD deactivated, Hot key of the brightness control and DOWN(
decreases the brightness. With OSD activated, move the cursor downward. PLUS(
: With OSD deactivated, Hot key of the contrast control and increases the contrast. With OSD activated, enter sub menu and increases the adjustment of the selected function. MINUS(-) : With OSD deactivated, Hot key of the contrast control and decreases the contrast. With OSD activated, decreases the adjustment of the selected function. SOURCE :
For the extra function, normally no need to use this button. Adjusting OSD PICTURE 1. BRIGHTNESS Increase or decrease the brightness (Range : 0~100) 2. CONTRAST Increase or decrease the Contrast (Range : 0~100) 3. BACK LIGHT Increase or decrease the CCFL back light luminance (Range : 0~100) COLOR TEMP 1. MODE Change the Color mode ( 6500, 7200, 9300, USER ) 2. RED Red balance (Only Working with USER mode) (Range : 0~100) 3. GREEN Green balance (Only Working with USER mode) (Range : 0~100) 4. BLUE Blue balance (Only Working with USER mode) (Range : 0~100) 9 - English LCD MONITOR 9 User s Manual LCD MONITOR 10 User s Manual English - 10 IMAGE 1. IMAGE SIZE Change the image size (Scaling mode) (Full,Fill aspect, 1:1) 2. SHARPNESS Set the sharpness of image (Softest,Softest,Normal,Sharp,Sharpest) 3. RESET SETTINGS Changes all OSD values to factory outgoing status. SETUP 1. LANGUAGE Change the OSD language orean,English,French,Spanish,German,Chinese,Japanese,Italian 2. OSD COLOR Adjust the OSD back ground from white opaque to half translucent. 3. OSD POSITION Change the OSD position (9 postions) 4. DURATION Adjust OSD display time
(5, 10, 20, 30, 60, 90, 120, 180, 240 seconds) Standard Signal Table PC Supported Mode Resolution Horizontal Frequency
(KHz) Vertical Frequency
(Hz) Clock Frequency
(MHz)
(640 X 480)
(640 X 480)
(640 X 480)
(640 X 480)
(800 X 600)
(800 X 600)
(800 X 600)
(800 X 600)
(800 X 600)
(800 X 600)
(1024 X 768)
(1024 X 768)
(1024 X 768)
(1280 X 768)
(1280 X 720)
(1280 X 720)
(1280 X 1024)
(1366 X768) 31.5 37.9 37.5 43.3 31.5 35.1 37.9 48.1 46.9 53.7 48.4 56.5 60 47.7 37.5 45 64 48.32 60 72 75 85 50 56 60 72 75 85 60 70 75 60 50 60 60 60 25.175 31.5 31.5 36 35.4375 36 40 50 49.5 56.25 65 75 78.75 79.5 74.25 74.25 108 87.75 LCD MONITOR 11 User s Manual LCD MONITOR 12 User s Manual Pin No. 1 2 3 4 5 6 7 8 9 Assignment Ground Speaker ID4 Speaker ID3 Speaker ID2 Speaker ID1 Speaker Out Left-
Speaker Out Left+
Speaker Out Right-
Speaker Out Right 1 5 9 6 9 Pin D-sub Pin assignment table of signal connector Pin No. Assignment 1 2 3 4 5 6 7 8 Red Green Blue Ground DDC 5V Standby Cable Connection check Ground-Red Ground-Green Ground-Blue Pin No. 9 10 11 12 13 14 15 Assignment NC Ground-Sync Ground DDC Data H.Sync V.Sync DDC Clock Pin No. Assignment 1 2 3 4 5 6 7 8 9 10 11 12 T.M.D.S. Data2-
T.M.D.S. Data2+
T.M.D.S. Data2 Shield No Connect No Connect DDC Clock DDC Data No Connect T.M.D.S. Data1-
T.M.D.S. Data1+
T.M.D.S. Data1 Shield No Connect Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Assignment No Connect No Connect Cable Connection check Hot Plug Detect T.M.D.S. Data0-
T.M.D.S. Data0+
T.M.D.S. Data0 Shield No Connect No Connect Cable Connection check T.M.D.S. Clock+
T.M.D.S. Clock-
6 9 1 5 15 11 15pin D-Sub 1 8 24 17 24 Pin DVI-D 10 16 Pin No. 1 2 Assignment Coaxial S/PDIF audio signal Ground 2 1 RCA LCD MONITOR 13 User s Manual LCD MONITOR 14 User s Manual Specification Troubleshooting Model LCD Panel Type Screen Size Maximum Resolution Pixel Range Display Colors Contrast Ratio Viewing Angle Response Time Luminance Horizontal Frequency Vertical Frequency Maximum standby Mode Synchro nization Power Consumption Control key Rear side Video Audio Video Audio Input Signal Compati bility Safety Standard
& EMI Dimension FS-L4201C a-si TFT Active matrix 106.7cm (Diagonal) 1366 X 768@ 60 Hz 0.681(H) mm X 0.227(V) mm 16.7M (RGB 8-bit data) 1000 : 1 89 / 89 / 89 / 89 10 msec 500 cd/m 91kHz (Max.) 85Hz (Max.) 300W Under 20W SOURCE, -,+, Analog RGB DVI Digital S/PDIF (Coaxial) VGA,SVGA,XGA,WXGA IEC-958 S/PDIF 32kHz,44.1kHz,48kHz,96kHz Safety Standard UL,C-TICK,EK,CCC EMI CE,MIC,BSMI,FCC Size and Weight 1022 615 98 / 29kg Power LED is dark. No picture. Check the power connection.
(Refer to page 5) Power LED is Red Check the signal cable or signal Source.
(Refer to page 5) Screen is not clear. Remove and check attaches to the signal line
(Video extension cable and others) and switch on. Display is unstable and trembling. Check the resolution and frequency of computer and video card, and set up again.Refer to the current monitor mode and standard signal mode table.
(Refer to page 12) Color is irregular. Adjust COLOR at User Mode in OSD Color Temp Menu. LCD MONITOR 15 User s Manual LCD MONITOR 16 User s Manual Warning To prevent damage or loss, please read this warning carefully. Double images or
'ghosts'. Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.
(Refer to page 5) When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. Picture is dark. Adjust COLOR at User Mode in OSD Color Temp Menu. To prevent electric shock, do not connect/dis-
connect the plug with wet hand. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. To prevent fire, do not connect a large number of equipments in a single line. To prevent fire and electric shock, pull out the plug in case of thunder and lightening. To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local service station or customer service center for inspection, modification or repair. LCD MONITOR 17 User s Manual LCD MONITOR 18 User s Manual 19 - English