Users Manual 52 Dual Color TFT LCD Monitor Model Name : FS-S5202C Model Number : 0100400003AA Customer Project name : Aquarius Dual Item name :
TANDBERG Monitor Dual 52 Assembly TANDBERG Item number :
117336 Init Tech App Vendor Vendor/Manufacturer must guarantee that assembly is in compliance with RoHS directive(tick-off) Changes : Rev 01 First build of the specification Vendor/Manufacturer Part No Date Sign FS-S5202C Page 1 of Rev.:01-draft 0100400003AA All contents are confidential Do not copy INFORMATION TO USER :
General Specification 1. General Description and Scope 2.1 General Description This specification applies to the Type 52 Color TFT/LCD Module LTI520HB01. This module is designed for a LCD TV style display unit. The screen format and electrical interface are intended to support the VESA WUXGA (1920(H) 1080(V) at 60Hz) screen. Supported Color is native 16.7M colors (RGB-8bit data driver). All input signals are LVDS (Low Voltage Differential Signaling) interface compatible. 2. Environmental and Reliability Specifications 3.1 Operating Conditions 3.1.1 Temperature : 0~ 40 Note : Max. Operating Temperature 40 in the spec means the temperature measured at the point of the front surface of the LCD glass cell. 3.1.2 Humidity : 10% ~ 90%, non-condensing 3.1.3 Altitude : maximum 4,500m 3.1.4 Test Type Low temperature Parameters T = 0C Dwell time = 8h + 2h (power-off) Cold start-up after the power-off period High temperature T = +40C Dwell time = 8h + 2h (power-off) Warm start-up after the power-off period Low pressure P = 60kPa (4206m) Pressure dwell time = 2h T = +40C Description and comments Results Passed 1h 0.5h Lab amb 0 0.5h Lab amb 1h 8h 2h 8h 2h 1h 0.5h 0.5h 1h Shield the unit against direct airflow 3.5h 2.5h Lab amb h 1 0
. h 1 0
. 0.5h 2h 1h 0.5h 1h Shield the unit against direct airflow Passed Passed Document No. D&TQP0302-11(0) Revision No. 01 Page 2 of 22 3.2 Non-Operational Conditions 3.2.1 Temperature : -20~ 60 3.2.2 Humidity : 10% ~ 90%, non-condensing 3.2.3 Altitude : maximum 15,000m 3.2.4 Test Type Low temperature Parameters T = -20C Dwell time = 16h Description and comments Results Passed Passed Passed Passed 60 30 9h 3h 3h 9h One cycle High temperature T = +60C Dwell time = 16h Thermal shock Low temperature = -20C High temperature = +60C Temperature gradient =
5C/min Dwell time = 2h No. of cycles = 3 Humidity RH = 90%
Low temperature = 30C High temperature = 60C No. of cycles: 5 ea 24h Document No. D&TQP0302-11(0) Revision No. 01 Page 3 of 22 3.3 Packing Conditions 3.3.1 Temperature : -20~ 50 3.3.2 Humidity : 10% ~ 90%, non-condensing 3.3.3 Altitude : maximum15,000m 3.3.4 Test Type Freefall Drop Parameters Drop surface Drop height Impact area Concrete or steel Weight > 100kg: 0.1m 6 faces 1 selected corner 1 selected edge vibration No. of drops Frequency range Displacement Acceleration Sweep rate Duration 1 per impact area 5-10Hz 3.5mm 3min(5-50-5) Right/Left : 15min Front/Back : 15min Up/Down : 30min 10-50Hz 1g Result Passed Passed Document No. D&TQP0302-11(0) Revision No. 01 Page 4 of 22 3. Input Signal and AC Power 4.1 AC Power 4.1.1 AC input voltage : AC 100 to 240 Volts (Universal power) 4.1.2 AC input frequency : 50~60Hz 3Hz 4.2 Video and Sync Signal 4.2.1 Video signal A. Horizontal frequency : 25 ~ 90KHz B. Vertical frequency : 24 ~ 120Hz C. Applicable maximum pixel frequency : 170MHz(Analog), 165MHz(Digital) D. Maximum resolution : 1920x1200 / 60Hz 4.2.2 Signal connectors A. HDMI type Ax3x2(Dual) : HDMI input B. 15p D-Sub(Female, 3row) x1x2(Dual) : Analog RGB input C. 9p D-Sub (Female) x1x2(Dual) : RS232C Input D. 9p D-Sub (Male) x1x2(Dual) : RS232C Output E. 15p D-Sub(Male, 2row) x1x(Dual) : Audio AMP signal input F. AC Inlet x1x2(Dual) : main AC power input 4. Electrical Performance: Except where noted, the following test conditions are required. 5.1 Standard Testing Conditions 5.1.1 AC power voltage and frequency : AC 100 ~ 240V10%, 60Hz/50Hz3Hz 5.1.2 Ambient temperature: 25 5 5.1.3 Brightness setting : set brightness control to the maximum level of the OSD 5.1.4 LCD panel direction : test at the parallel position with LCD panel center line 5.1.5 Ambient light level : between 300 lux and 700 lux 5.2 Power management 5.2.1 Power management
: This system can save energy by switching this monitor into a low-mode when the display video signal is none. But power Management system can not be corresponded with VESA DPMS, because of the TANDBERGs operation specification. 5.2.1 Power Management Modes. State Normal operation DPMS or Standby mode Sleep mode Power consumption Max 1000Wrms Max 50Wrms Max 3.5Wrms Document No. D&TQP0302-11(0) Revision No. 01 Page 5 of 22 5.3 LCD (Liquid Crystal Display) Panel Specifications This specification applies to the Type 52 Color TFT/LCD Module LTI520HB01. This module is designed for a LCD TV style display unit. The screen format and electrical interface are intended to support the WUXGA(1920(H) 1080(V)) screen. Supported gray scales are native 8bit per 1(one) sub pixel. All input signals are LVDS(Low Voltage Differential Signaling) interface compatible. 5.3.1 General specification diagonal viewable Item Display area Driver element Number of Pixels Pixel Pitch Pixel arrangement Display colors Viewing angle(max) Display mode SPECIFICATION 1321 1152.0(H) 648.0(V) a-Si TFT Active matrix 1920x1080, 2.07Million 0.6(H) 0.6(V) R. B, G Vertical Stripe 16.7M (RGB 8-bit data) 178(H), 178(V) Normally black UNIT mm mm pixels mm degrees NOTE 120 minutes after lighting on 5.3.2 Optical characteristics (LCD panel specification) The following optical characteristics are measured under stable conditions. It takes about 120minutes to reach stable conditions. The measuring point is the center of display area unless otherwise noted. The optical characteristics should be measured in a dark room or equivalent state. Measuring equipment : TOPCON BM-7, SPECTRORADIOMETER SR-3 Temperature of LCD surface=25, VDD=12.0V, fV=60Hz, BRT=High(PWM Duty 100%) ITEM SYMBOL CONDITION Contrast Ratio Response Rise Fall Brightness of white Time Red Color Green Chromaticity
(CIE) Blue White Hor Ver Viewing Angle C/R Tr Tf Bwh x y x y x y x y L R U D
=0 1) Min. 1300
500 TYP
-0.03 75 75 75 75 Typ. 1700 14 8 600 0.645 0.336 0.275 0.606 0.143 0.067 0.280 0.290 89 89 89 89 Max. UNIT
24 10
ms ms cd/m TYP
+0.03
Degree Document No. D&TQP0302-11(0) Revision No. 01 Page 6 of 22 L =90 o x L = 90 o y*
N orm al L ine
= 0 o,
= 0 o L L H R y H = 90 o x*
R =90 o Definition of Response time :
Display data Black(TFT OFF) White(TFT ON) Black(TFT OFF) TR TF Optical Response 100%
90%
10%
0%
5.3.3 Luminance Uniformity When the backlight is on with all pixels in the white (maximum gray) level, the luminance uniformity is defined as follow;
Time Where;
Lbright : The luminance of the brightest part of the area Ldark :The luminance of the darkest part of the area Adjacent Area Luminance Uniformity = ( Lbright - Ldark ) / Lbright 0.25 Over a circular area of 10mm diameter placed anywhere on the screen Screen Total Luminance Uniformity = ( Lbright - Ldark ) / Lbright 0.25 Over the entire screen 5.4 Front of screen (FOS) performance 5.4.1 Chromaticity(White) : X = 0.280, Y = 0.290 5.4.2 Luminance : no less than 500/
Controls setting condition : contrast and brightness max Document No. D&TQP0302-11(0) Revision No. 01 Page 7 of 22 5.4.3 Minimum luminance : less than 30cd/ with full white pattern at the contrast default and minimum brightness and minimum back light level 5.4.4 Gray scale linearity : The 16 step gray bars shall be distinguishable at the default contrast and default brightness or 3 steps down contrast setting of the OSD menu 5.4.5 Noise : Pixel displacement, jitter, or swim shall not be visible to the eye when viewed at 50cm from the LCD panel surface. 5.5 Defect
: Defects are considered to be impairments to video quality, which exist independently of displayed information. They may be electrical, mechanical, or physical imperfection of display resulting from processing, handling, shipping, etc. 5.5.1 Bright and Black Dots The following Table describes the specification of bright and black dots in the visual screen quality of the TFT-LCD module at power-ON. Items Any Bright Dots(Two joined dot must be counted 2) Any Black Dots(Two joined dot must be counted 2) Bright and Black Dots(total) Two Joined Bright Dots Three Joined Bright Dots. Two joined Black Dots Three Joined Black Dots Minimum distance between dot defects Bright dot Bright dot Black dot Black dot Basic Conditions:
Viewing Distance 150010 mm Ambient Illumination 300~700 lux(Normal 500lux) Ambient Temperature 255 5.5.2 Visual Screen Quality Specification 5x2 Max 10x2 Max 15x2 Max 1x2 Max 1x2 Max 2x2 Max 1x2 Max 5mm Ignore Item Foreign Material
(in the polarizer, Cell) Bright Foreign Material
(in polarizer or cell) Scratches on the polarizer / glass Dent on the polarizer / glass Size(mm) Circular 0.3D3.0 2L15.0 Linear 0.3D0.5 2L15.0 0.3D0.8 Permissible Number 5 5 5 5 10 Operation Condition with white picture with white or black picture with black picture Non operation
D: Average Diameter, L: Length, Document No. D&TQP0302-11(0) Revision No. 01 Page 8 of 22 5. Signal Connections and Pin Assignments 6.1 AC Inlet socket Pin 1 2 3 Signal Assignment Live Neutral GND 6.2 HDMI Connector (Type A) Signal Assignment TMDS Data2+
TMDS Data2-
TMDS Data1 Shield TMDS Data0+
TMDS Data0-
Pin 1 3 5 7 9 11 TMDS Clock Shield 13 NC 15 DDC SCL 17 DDC Ground 19 Hot Plug Detect Signal Assignment TMDS Data2 Shield TMDS Data1+
TMDS Data1-
TMDS Data0 Shield TMDS Clock+
TMDS Clock-
NC DDC SDA
+5V Power Pin 2 4 6 8 10 12 14 16 18 Document No. D&TQP0302-11(0) Revision No. 01 Page 9 of 22 6.3 15pin D-Sub Connector : Analog RGB signal input Pin 1 2 3 4 5 6 7 8 Signal Assignment Red Green Blue GND DDC 5V Standby
/Cable connection check GND-Red GND-Green GND-Blue Pin 9 10 11 12 13 14 15 Signal Assignment NC GND-Sync GND DDC SDA H Sync V Sync DDC SCL 6.4 9pin D-Sub(Female) Connector : RS232C Input Pin 1 2 3 4 5 Signal Assignment RS232 ID RS232 RXD RS232 TXD NC GND Pin 6 7 8 9 Signal Assignment NC NC
+5V Output NC 6.5 9pin D-Sub(Male) Connector : RS232C Output
This connector is used for chain connection with other Eagle monitor. Document No. D&TQP0302-11(0) Revision No. 01 Page 10 of 22 Signal Assignment Pin 1 2 3 4 5 Signal Assignment NC RS232 RXD RS232 TXD NC GND Pin 6 7 8 9 NC NC NC NC 6.6 15pin D-Sub(Male, 2row) Connector Signal Assignment Signal Assignment Speaker ID 1 Speaker ID 0 Left Full Range +
Left Full Range -
Pin 1 2 3 Center Tweeter +
4 Center Tweeter -
5 Center woofer1 +
6 Center woofer1 -
7 Center woofer2 +
8 Center woofer2 -
This connection is optimized for TANDBERGs DNAM AMP system, And DNAM Identify the speaker ID so that output appropriate audio signal to match this monitors speaker module.*
Pin 9 10 11 Right Full Range +
12 Right Full Range -
13 14 AMP Ground 15 Speaker ID 2 LMNT
On this monitor the pin1(Speaker ID 1) must be connected to ground by using internal speaker wiring. LMNT Pin name 1 Set digit to 1 : must be floated 0 : must be tied to circuit ground Speaker ID 2 1 Speaker ID 1 0 Speaker ID 0 1 Document No. D&TQP0302-11(0) Revision No. 01 Page 11 of 22 6. Supported Timing 7.1 Standard Timing Chart Resolution Timing Item Pixel Clock (MHz) Sync Polarity (H/V) Scanning Type
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms) Resolution Timing Item Pixel Clock (MHz) Sync Polarity (H/V) Scanning Type
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms) Resolution Timing Item Pixel Clock (MHz) Sync Polarity (H/V) Scanning Type
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms) 640x480
@60Hz 25.175 N/N 800x600
@50Hz 35.4375 P/P 800x600
@60Hz 40.000 P/P 800x600
@75Hz 49.500 P/P 1024x768
@60Hz 65.000 N/N 1280x720
@50Hz 74.250 P/P 1280x720
@60Hz 74.250 P/P Progressive Progressive Progressive Progressive Progressive Progressive Progressive 1280x720
@100Hz 1280x720
@120Hz 1280x1024
@60Hz 1280x768
@60Hz 1360x768
@60Hz 1366x768
@60Hz 1400x1050
@60Hz Progressive Progressive Progressive Progressive Progressive Progressive Progressive 31.469 31.778 25.422 0.318 3.813 1.589 59.940 16.683 15.253 0.064 0.064 0.794 148.500 P/P 75.000 13.333 8.620 2.963 0.269 1.481 100.000 10.000 9.600 0.066 0.067 0.267 64.674 15.462 14.118 0.403 0.269 0.672 59.883 16.699 16.235 0.031 0.093 0.340 31.500 31.746 22.575 1.129 3.612 4.430 50.000 20.000 19.048 0.032 0.127 0.794 148.500 P/P 90.000 11.111 8.620 0.741 0.269 1.481 120.000 8.333 8.000 0.055 0.056 0.222 75.000 13.333 9.877 0.395 1.185 1.877 60.000 16.667 16.000 0.013 0.040 0.613 37.879 26.400 20.000 1.000 3.200 2.200 60.317 16.579 15.840 0.026 0.106 0.626 108.00 P/P 63.981 15.630 11.852 0.444 1.037 2.296 60.020 16.661 16.005 0.016 0.047 0.594 27.000 37.037 25.859 8.592 0.593 1.993 24.000 41.666 40.000 0.148 0.185 1.333 46.875 21.333 16.162 0.323 1.616 3.232 75.000 13.333 12.800 0.021 0.064 0.488 79.500 N/P 47.776 20.931 16.101 0.805 1.610 2.415 59.870 16.703 16.075 0.063 0.147 0.419 28.125 35.555 25.859 7.110 0.593 1.993 25.000 40.000 38.400 0.142 0.178 1.280 48.363 20.677 15.754 0.369 2.092 2.462 60.004 16.666 15.880 0.062 0.124 0.600 85.500 P/P 47.712 20.959 15.906 0.749 1.310 2.994 60.015 16.662 16.097 0.063 0.126 0.377 33.750 29.629 25.859 1.184 0.593 1.993 30.000 33.333 32.000 0.116 0.148 1.067 37.500 26.667 17.239 5.926 0.539 2.963 50.000 20.000 19.200 0.133 0.133 0.533 87.750 N/P 48.320 20.695 15.567 0.661 0.912 3.556 59.803 16.722 15.894 0.041 0.248 0.538 48.000 45.000 22.222 17.239 1.481 0.539 2.963 60.000 16.666 16.000 0.111 0.111 0.444 121.751 N/P 65.317 15.309 11.499 0.607 1.240 1.963 59.979 16.672 16.075 0.046 0.061 0.490 56.250 17.777 12.929 3.555 0.296 0.997 50.000 20.000 19.200 0.071 0.089 0.640 1680x1050
@60Hz 119.000 P/N 1600x1200
@60Hz 162.000 P/P 1920x1080
@24Hz 74.250 P/P 1920x1080
@25Hz 74.250 P/P 1920x1080
@30Hz 74.250 P/P Progressive Progressive Progressive Progressive Progressive Progressive Progressive 1920x1080
@50Hz 148.500 P/P 1920x1080
@48Hz 148.5 52.000 Document No. D&TQP0302-11(0) Revision No. 01 Page 12 of 22 Resolution Timing Item Pixel Clock (MHz) Sync Polarity (H/V) Scanning Type
-Hor Frequency (kHz)
-Period (us)
-Active time (us)
-Front porch (us)
-Sync width (us)
-Back porch (us)
-Ver Frequency(Hz)
-Period (ms)
-Active time (ms)
-Front porch (ms)
-Sync width (ms)
-Back porch (ms) 1920x1080
@60Hz 148.500 P/P 1920x1200
@60Hz 154.000 P/N Progressive Progressive 67.500 14.814 12.929 0.592 0.296 0.997 60.000 16.666 16.000 0.059 0.074 0.533 74.038 13.506 12.468 0.312 0.208 0.519 59.950 16.681 16.208 0.041 0.081 0.351 Document No. D&TQP0302-11(0) Revision No. 01 Page 13 of 22 7. User control function 8.1 User Controls RS232C command from external controller
@@1KESPWR
@@1KESMNU We will not provide remote controller, because no need to control the OSD function normally, but will provide it for service engineer to check the RS232C function easily. Following is the description how you can adjust or change the OSD function Function name Operation POWER MENU SOURCE UP DOWN PLUS MINUS SET Monitor power on and off With OSD deactivated, Activated to OSD menu With OSD activated, Exit from main menu or sub menu. With OSD deactivated, you can see the kind of displayed source on right under of the screen. With OSD deactivated, Hot key of the brightness control and increases the brightness. With OSD activated, move the cursor upward. With OSD deactivated, Hot key of the brightness control and decreases the brightness. With OSD activated, move the cursor downward With OSD deactivated, Hot key of the contrast control and increases the contrast. With OSD activated, enter sub menu and increases the adjustment of the selected With OSD deactivated, Hot key of the contrast control and decreases the contrast. With OSD activated, decreases the adjustment of the selected function. With OSD activated, Enter sub menu and change each sub menus item
@@1KESSRC
@@1KESUPK
@@1KESDWN
@@1KESPLS
@@1KESMNS
@@1KESSET
3rd character 1 of the RS232C command is the unit ID, so this can be changed according to unit ID. Document No. D&TQP0302-11(0) Revision No. 01 Page 14 of 22 8. Special Consideration 9.1 All the supported timing modes (includes LCD Panel mode) are described in chapter8.
(Optimized with TANDBERGs requirement signal timing) 9.2 This model have plug & play feature of DDC 1, DDC2B. This function is operating when the monitor is connected to a system compatible with VESA DDC standard. The DDC data structure is based on VESA DDC 1.3 standard 9.3 You can adjust and change the several function without buttons, by using RS232C serial communication protocol through 9pin D-Sub (Female) connector.
(Refer to RS232C serial interface protocol) 9.4 RS232C chain connection with several monitor is available through RS232C IN/OUT connector.
(ex, TANDBERGs T3 system, Max 9 monitor) So you can adjust and change the several monitor individually or at the same time.
:The products described in this specification must meet all applicable safety and regulatory requirements as listed in this chapter. 9. Applicable Regulations 10.1 Approvals-Europe(CE Mark) Type CE Mark LVD Directive 73/23/EEC Requirement All Products must have CE mark Standards for LVD:
IEC/EN 60950-1 2nd ed CB according to IEC60950-1 incl all the different nation deviations. Special requirements. Ambient temperature 40 CI. 5. 1 Touch current Max 0.5mA touch current with switch ON and OFF position. Approved to 3,000 meter altitude above sea level. EN 55022 : 2005 (Class B) EN 55024 : 1998 Incl A1/A2 EN 61000-3-2 : 2000 EN 61000-3-3 : 1995 Incl A1 Testing:
All testing must be performed in accredited test laboratory EMC testing must be performed in laboratory appointed as competent body according to the EMC directive EMC Directive 89/336/EEC RoHS Directive Product must comply with the European RoHS Directive 2002/95/EC Signed declarations or test reports is accepted to document compliance. 10.2 Approvals-North America(USA/Canada : UL, FCC Mark) Requirement Product must be tested and approved according to relevant standard CSA 60950-1-07 2nd ed / UL 60950-1 2nd ed Approval agency must be accredited as an NRTL EMC Requirements according to FCC15B (Class B) Type Electrical Safety EMC Document No. D&TQP0302-11(0) Revision No. 01 Page 15 of 22 10. Entire system block diagram Document No. D&TQP0302-11(0) Revision No. 01 Page 16 of 22 11. Mechanical and printing Specifications This monitor is used for TANDBERGs video conferencing system EAGLE. Following dimension and outward sharp is designed by TANDBERG originally. 16.1 Outward drawing and Weight Outward Size Weight 2412 X 170 X 867 mm Max 130Kg 16.2 Product label 16.2.1 Brand Logo : TANDBERG 16.2.2 Model No : FS-S5202C 16.2.3 Rating Label (This may vary based on the TANDBERG's request, and the changed contents of the Rating Label shall not be specified in this specification.) A. Location : on the top module (Refer to the following picture) B. Tilt : Shall not be tilted more than 1mm C. Size : 40 x 102 mm (R0.5 x 4edge) D. Material : Enumudeurong (Polyester film) E. Base Color : Black F. Printing Color : PMS877(Silver) G. Description:
Document No. D&TQP0302-11(0) Revision No. 01 Page 17 of 22 Rev: 1 16.2.4 Products barcode label and Serial number structure A. Location : On the product label B. Tilt : Shall not be tilted more than 1mm C. Size : 70 x 11mm D. Material : Art paper E. Base Color : White F. Printing Color : Black G. Description:
Serial No digit 1 2 3 4 Item D 9 A E 5~8 0001 Initial This mean D&T Inc Build year (7:2007, 8:2008, 9:2009~) Build month(A: January, B: February, ~L: December) Model (A : FS-L4201C, B: FS-S5201C, C: FS-P6501C, D: FS-
L4205C, E : FS-S5202C....) Serial Number (0001~9999) Manufactured digit 1~4 5~6 Item 2009 01 Initial Build year Build month(01:January, 02:February, ~12: December) Document No. D&TQP0302-11(0) Revision No. 01 Page 18 of 22 16.3 Packing Specification (Full set 1unit) 16.3 1 Dimension Width Depth Height Carton box
(Outside, Full set 1 unit) 1500mm 1100mm 1240mm 16.3.2 Packing Weight & Volume Packing Weight(Max) Volume kg 170 lbs 375 m3 2.05 ft3 72.26 Document No. D&TQP0302-11(0) Revision No. 01 Page 19 of 22 16.3.3 Cushion and inside view Document No. D&TQP0302-11(0) Revision No. 01 Page 20 of 22 16.3.4 BOX label A. Location : On the 2 narrow side of carton box (Refer to the following picture) B. Tilt : Shall not be tilted more than 3mm C. Size : 104 x 127mm D. Material : Art paper E. Base Color : White F. Description:
G. Barcode structure(when we read the barcode by reader: 0100000000117336240P21D9AE0001)
*The barcode is in accordance with UCC/EAN128 format*
Initial Item First reference 01 00000000 Supplementary 8 digits 117336 240 P 21 D 9 A E 0001 TANDBERGs item number Second reference Variant Third reference This mean D&T Inc Build year (7:2007, 8:2008,~) Build month(A: January, B: February, ~L: December) Model (A : FS-S5202C, ) Serial number (0001~9999) Same as products barcode digits Readied digit 1~2 3~10 11~16 17~19 20 21~22 23 24 25 26 27~30 Document No. D&TQP0302-11(0) Revision No. 01 Page 21 of 22 16.5 Container loading 16.5.1 In case of 20ft container
: 6 pallets= 18units 16.5.2 In case of 40ft container
: 13 pallets= 39units Document No. D&TQP0302-11(0) Revision No. 01 Page 22 of 22