LCD MONITOR Users Guide FS-A4206F/FS-A4206C INFORMATION TO USE :
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation. If this equipment is found to cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by carrying out one or more of the following measures:
p g 1. Reorient or relocate the receiving antenna. 2. Increase the distance between the color monitor and the subject of interference. f 3. Plug the monitor into a outlet on a different electrical circuit than that to which the subject of interference is connected. 4. Consult the dealer or an experienced radio/TV technician for help. CAUTION Modifications not expressly approved by the manufacturer responsible for compliance could void the warranty of the product. Attempts by the user to disassemble or modify the monitor will void the warranty. General Specification Table of contents 1. Part--------------------------------------------------------------------------------------------------- 1 2. Product drawing----------------------------------------------------------------------------------- 2 3. Monitor Connection----------------------------------------------------------------------------- 3 4. Function key--------------------------------------------------------------------------------------- 5 5. OSD adjust --------------------------------------------------------------------------------------- 7 6. Standard signal table ---------------------------------------------------------------------------- 9 7. Signal Connector pin assignments ----------------------------------------------------------- 10 8. Specification ------------------------------------------------------------------------------------- 12 9. Safety instructions ----------------------------------------------------------------------------- 14 General Specification LCD MONITOR Parts 42 LCD Monitor USER MANUAL AC power extension Cable(Option) Serial Cable
(Option) DVI-HDMI Cable
(Option) 1 General Specification Product drawingg LCD MONITOR Unit : mm 2 LCD MONITOR Monitor Connection FS-A4206C FS-A4206F 3
/ ff S h 1. AC on/off Switch 1 AC 2. AC Inlet. 3. 29 Pin DVI in connector 4. 29 Pin DVI Out connector 5. 15 Pin VGA connector 6. 9 Pin RS-232 connector 1. AC on/off Switch 2. AC Inlet. 3. 29 Pin DVI in connector 4. 9 Pin RS-232 connector Power source connection Signal cable connection g LCD MONITOR DVI In,Out put To the AC inlet connector To the AC inlet connector VGA Analog AC Input RS-232 AC on/off switch 1. Use 220V or 110V. 2. Connect the DVI Cable to the monitor. 3. Power on the monitor. 4. Done. General Specification 4 LCD MONITOR Function keyy An 8 button keypad, located in rear side of the display, allows the user to make adjustments to various display parameters using the On Screen Display(OSD) system. Indicate the power status and input signal status p p g Normal mode : Always green Standby mode : Blinking green(ex, No signal) Sleep mode : Always red Note 1 : LED normal and off mode sign can be changed according to the requirement of the customer whether normal mode green is on or off Note 2 : The main AC power switch, on the back panel, should be in the ON position. Th DC The DC power button is used to turn on the monitor h i d b i On-Screen Display (OSD) Function Button 1. POWER : Monitor power on and off 2. MENU : With OSD deactivated, Activated OSD menu. With OSD activated Exit from main menu or sub menu With OSD activated, Exit from main menu or sub menu. 3. UP () : With OSD deactivated, Hot key of the brightness control and increases the brightness. With OSD activated, move the cursor upward. 4. DOWN () : With OSD deactivated, Hot key of the brightness control and decreases the brightness. With OSD activated, move the cursor downward. 5 General Specification LCD MONITOR 5. PLUS(+) : With OSD deactivated, Hot key of the contrast control and increases the contrast. With OSD activated, enter sub menu and increases the adjustment of the selected. With OSD activated, enter sub menu and increases the adjustment of the selected. 6. MINUS(-) : With OSD deactivated, Hot key of the contrast control and decreases the contrast. With OSD activated, decreases the adjustment of the selected function. 7.INPUT : With OSD deactivated, you can see the kind of displayed source on lower right of the screen. 8. PIP : Picture in picture function will be activated and change the picture layout.
(This function is provided for FS-A4206C Model only) 6 LCD MONITOR OSD adjust j PICTURE COLOR TEMP 7 General Specification BRIGHTNESS Increase or decrease the brightness. (Range : 0 ~ 100) CONTRAST Increase or decrease the contrast. (Range : 0 ~ 100) BACKLIGHT Increase or decrease the backlight. (Range : 0 ~ 100) MODE Change the color temperature mode : 6500K, 7200K, 9300K, USER When USER is selected, a sub-menu displays allowing the user to adjust the RED, GREEN or BLUE balance. user to adjust the RED, GREEN or BLUE balance. RED Red balance Only works on the USER mode. (Range : 0 ~ 100) GREEN Green balance Only works on the USER mode. (Range : 0 ~ 100) BLUE BLUE Blue balance Only works on the USER mode. (Range : 0 ~ 100) IMAGE OSD SETUP LCD MONITOR IMAGE Change the image size : FILL ASPECT, FILL ALL, ONE TO ONE SHARPNESS Set the sharpness of the image.
(SOFTEST, SOFT, NORMAL, SHARP, SHARPEST) RESET SETTINGS Restore all the OSD values to factory out-going status. UNIT ID Change the unit identification. (Range : 1 ~ 9) LANGUAGE Change the OSD Language. (8 languages English, German, French, Spanish, Italian, Chinese, Japanese, Korean) OSD COLOR Adjust transparency of OSD background. (Range : 0 ~ 100) OSD POSITION Change the OSD position. DURATION Adjust OSD display time.(5, 10, 20, 30, 60, 90, 120, 180, 240 seconds) General Specification 8 LCD MONITOR Standard signal table g PC Supported mode Resolution 640x480@60Hz
800x600@50Hz 800x600@50Hz 800x600@75Hz 1024x768@60Hz 1280 720@50H 1280x720@50Hz 1280x720@60Hz 1280x720@100Hz 1280x720@120Hz 1280x1024@60Hz 1280x768@60Hz 1360x768@60Hz 1366x768@60Hz 1400x1050@60Hz 1680x1050@60Hz 1600x1200@60Hz 1920x1080@24Hz 1920x1080@25Hz 1920x1080@30Hz 1920x1080@50Hz 1920x1080@60Hz 1920x1200@60Hz Horizontal Frequency(KHz) Vertical Frequency(Hz) Clock Frequency(MHz) 31.469 31.500 37.879 46.875 48.363 37 500 37.500 45.000 75.000 90.000 63.981 47.776 47.712 48.320 65.317 64.674 75.000 27.000 28.125 33.750 56.250 67.500 74.038 59.940 50.000 60.317 75.000 60.004 50 000 50.000 60.000 100.000 120.000 60.020 59.870 60.015 59.803 59.979 59.883 60.000 24.000 25.000 30.000 50.000 60.000 59.950 25.175 35.4375 40.000 49.500 65.000 74 250 74.250 74.250 148.500 148.500 148.500 79.500 85.500 87.750 121.751 119.000 162.000 74.250 74.250 74.250 148.500 148.500 154.000 9 General Specification Signal Connector pin assignments p g g LCD MONITOR DVI In,Out (DVI-I 29Pin) Pin No. Assignment Pin No. Assignment 1 2 3 4 5 6 7 8 9 10 11 TMDS Data2+
TMDS Data2+
TMDS Data2 Shield No Connection No Connection DDC Clock DDC Data No Connection TMDS Data1-
TMDS Data1+
TMDS Data1 Shield 13 14 15 16 17 18 19 20 21 22 23 12 No Connection 24 RS-232 (D-SUB 9Pin,female) No Connection
+5V Power Cable connection check Hot Plug Detect TMDS Data0-
TMDS Data0+
TMDS Data0 Shield No Connection No Connection TMDS Clock Shield TMDS Clock+
TMDS Clock-
Pin No. Assignment Pin No. Assignment 1 2 3 4 5 Test pin1(Note) RS-232 RXD Input p RS-232 TXD Input No Connection Ground 6 7 8 9 No Connection Test pin2(Note) Test pin3(Note) No Connection Note : Please keep these pins to no connection. General Specification 10 LCD MONITOR VGA (D SUB 15Pi ) VGA (D-SUB 15Pin) Pin No. Assignment Pin No. Assignment 1 2 3 3 4 5 6 6 7 8 Red Green Bl Blue Ground DDC 5V Standby Cable Connection check G d R d Ground-Red Ground-Green Ground-Blur 9 10 11 11 12 13 14 14 15 No Connection Ground-Sync G d Ground DDC Data H.Sync VS V.Sync DDC Clock 11 General Specification LCD MONITOR Specification p Model FS-A4206F Type A-si TFT Active matrix Display area 930.4(H) mm X 523.26(V) mm Maximum Resolution 1920X1080@120Hz LCD PANEL Pixel pitch 0.4845(H)mm X 0.4845(V)mm Display colors 1073.7M (RGB 10-bit data) Contrast Ratio(Typ.) 4000:1 Viewing Angle(Typ.) 89/89/89/89 Response Time(Typ.) 5ms Luminance(Typ.) 500cd/m2 Horizontal Frequency Horizontal Frequency 135.6 KHz 135.6 KHz Vertical Frequency 120 Hz Maximum 120W Standby Mode Under 0.5W Synchronization Power Consumption Power Power AC 100 240V~50 60Hz 1 2A Max AC 100-240V~50-60Hz 1.2A Max Approval Marks Approval Mark UL, FCC, Mx CoC, AR-S, CE, Gost-R, SASO, CCC, South Africa, KC BSMI, Singapore safety, C-Tick, CB Energy Efficiency China energy label, E-Standby Dimension Size and weight 1002.5X40X595 /17Kg(21Kg) General Specification 12 LCD MONITOR Model FS-A4206C Type A-si TFT Active matrix Display area 930.4(H) mm X 523.26(V) mm Maximum Resolution 1920X1080@120Hz LCD PANEL Pixel pitch 0.4845(H)mm X 0.4845(V)mm Display colors 1073.7M (RGB 10-bit data) Contrast Ratio(Typ.) 4000:1 Viewing Angle(Typ.) 89/89/89/89 Response Time(Typ.) 5ms Luminance(Typ.) 500cd/m2 Horizontal Frequency Horizontal Frequency 135.6 KHz 135.6 KHz Vertical Frequency 120 Hz Maximum 120W Standby Mode Under 0.5W Synchronization Power Consumption Power Power AC 100 240V~50 60Hz 1 2A Max AC 100-240V~50-60Hz 1.2A Max Approval Marks Approval Mark UL, FCC, CB Dimension Size and weight 1002.5X40X595 /17Kg(21Kg) 13 General Specification LCD MONITOR Safety instructions y Operator Safety Instructions For your safety, please read these safety instructions completely before you connect the equipment to the power source. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in these operating instructions operating instructions. Retain this manual for future reference. Water and Moisture Do not operate the apparatus under or near water - for example near a bathtub, kitchen sink, or laundry tub, in a wet basement, near a swimming pool or in other areas with high humidity. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Do not touch the product with wet hands. g Cleaning Unplug the apparatus from communication lines, mains power-outlet or any power source before cleaning or polishing. Do not use liquid cleaners or aerosol cleaners. Use a lint-free cloth lightly moistened with water for cleaning the exterior of the apparatus. Ventilation Do not block any of the ventilation openings of the apparatus. Never cover the slots and openings with a cloth or other material. Never install the apparatus near heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat. Do not place the product in direct sunlight or close to a surface directly heated by the sun. Lightning Never use this apparatus, or connect/disconnect communication cables or power cables during lightning storms. Dust Do not operate the apparatus in areas with high concentration of dust Vibration Do not operate the apparatus in areas with vibration or place it on an unstable surface. General Specification 14 LCD MONITOR d ti C V lt d H P Power Connection and Hazardous Voltage The product may have hazardous voltage inside. Never attempt to open this product, or any peripherals connected to the product, where this action requires a tool. This product should always be powered from an earthed power outlet. Never connect attached power supply cord to other products. In case any parts of the product has visual damage never attempt to connect mains power, or any other power source, before consulting service personnel The plug connecting the power cord to the product serves as the main disconnect device for The plug connecting the power cord to the product serves as the main disconnect device for this equipment. The power cord must always be easily accessible. Route the power cord so as to avoid it being walked on or pinched by items placed upon or against it. Pay particular attention to the plugs, receptacles and the point where the cord exits from the apparatus. Do not tug the power cord. If the provided plug does not fit into your outlet, consult an electrician. Never install cables, or any peripherals, without first unplugging the device from it's power source. Servicing Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Unplug the apparatus from its power source and refer servicing to qualified personnel under the following conditions:
following conditions:
If the power cord or plug is damaged or frayed. If liquid has been spilled into the apparatus. If objects have fallen into the apparatus. If the apparatus has been exposed to rain or moisture If the apparatus has been subjected to excessive shock by being dropped. If the cabinet has been damaged. If the apparatus seems to be overheated. If the apparatus emits smoke or abnormal odor. If the apparatus fails to operate in accordance with the operating instructions pp Accessories Use only accessories specified by the manufacturer, or sold with the apparatus. 15 General Specification Warning g LCD MONITOR When connecting to/disconnecting from a power outlet, push/pull on the plug itself. Never pull the cord, in order to prevent fire caused by a short. In order to prevent electric shock, do not connect/disconnect the plug with wet or moist hands. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. To prevent fire, do not connect a large number of equipments in a single line. To prevent fire and electric shock, pull out the plug in case of thunder and lightning. To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local service station or customer service center for inspection, modification or repair. General Specification 16 General Specification