FS-L2401D(24" ) FS-L2401D(
24" ) MEDIC AL LCD MONIT MEDIC USER'S GUIDE AL LCD MONITOROR Table of Contents Symbol Definitions Safety Instructions Caution FCC Information Parts Connector Mechanical Product Drawing Control Power mangement Adjust OSD Menu Stansard Signal table Signal connector Pin Assignments Specification 2 4 7 10 12 13 14 15 18 19 22 23 26 English - 1 Symbol Definitions The following symbols appear on the product. its labeling, or the product packing. Each symbol carries a special definition, as defined below Dangerous : High Voltage. Consult accompanying documents. Direct Current. lndicates protective earth ground. DC Power control switch. Serial Number. Top-Bottom. Fragile. Do not get wet. Maximum Stacking. Indicats proof of conformity to applicable European Econmic Community Council directives and to har-
monzed standards published in the official journal of the European Communities. Medical Equipment is in accordance with UL 60601-1 and CAN/CSA C22.2 No.601.1 in regards to electric shock, fire hazards, and mechanical hazards. Tested to comply with FCC Class B standards. Degrees of protection against the ingress of water. This symbol indicates that the waste of electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Please contact the manufacturer or other authorized disposal company to decommission your equipement. Tested to comply with VCCI Class B standards. Tested to comply with CCC standards. 2 - English English - 3 Safety Instructions On Safety 1.Before connecting the AC power cord to the DC adapter outlet make sure the voltage designation of the DC adapter corresponds to the local electrical supply. 2.Never insert anything metallic into the cabinet openings of the Liquid Crystal Display(LCD) monitor. doing so may create the danger of electric shock. 3.To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Only a qualified technician should open the case of the LCD monitor. 4.Never use your LCD monitor if the power cord has been damaged. Do not allow anything to rst on the power cord, and keep the cord away from areas where people can trip over it. 5.Be sure to hold the plug, not the cord,when disconnecting the LCD monitor from am electric socket. 6.Unplug your LCD monitor when it is going to be left unused for an extended period of time. 7.Unplug your LCD monitor from the AC outlet before any service. 8.if your LCD monitor does not operate normally-in particular, if there are any unusual sounds or smells coming from it-unplug it immediately am authorized dealer or service center. Warning Do not to touch signal input,signal output or other connectors, and the patient simultaneously. Warning Extrnal equipment intended for connection to signal input, signal output or other connectors, shall comply with relevant IEC stan-
dard(e.g.,IEC60950 for IT equipment and IEC60601 series for med-
ical electrical equipment). In addition, all such combination-system-shall comply with the stan-
dard IEC 60601-1-1, safety requirements for medical electrical sys-
tems. Any person who connectors has formed at system and is therefore responsible for the system to comply with the require-
ments of IEC 60601-1-1. if,in doubt, contact qualified technician or your local representative. On installation 1.Openings in the LCD monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. if you put the LCD monitor in a bookcase or some other enclosed space, be sure to provide adequate ventilation. 2.Put your LCD monitor in a location with low humidity and a minimum of dust. 3.Do not exepose the LCD monitor to rain or use it near water
(in kitchens, near swimming pools, etc.). if the LCD monitor accidentally gets wet, unplug it and contact an authorized dealer immediately.You can clean the LCD monitor with a damp cloth if necessary, but be sure to unplug the LCD monitor first. 5.Locate your LCD monitor near an easily accessible AC outlet. 6.High temperature can cause problems. Don't use your LCD monitor in direct sunlight and keep it away from heaters, stoves, fireplaces, and sources of heat. 4 - English English - 5 Environmental Conditions for transport and Storage
- Temperature range within -30C to 85C
- Relative humidity range 5% to 95%
Atrnospheric pressure range within 500 to 1060hPs. CAUTION
. This symbol alerts the user that important literature concerning the operation of this unit has been included. Therefore, it should be read carefully in order to avoid potential problems. This symbol warms user that un-insulated voltage within the unit the may have sufficient magnitude to cause electrical shock. Therefore, it is dangerous to make contact with any part inside the unit. To reduce the risk of electric shock, DO NOT remove cover (or back). There are no user serviceable parts inside. Refer servicing to qualified service personal. To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not use this unit's polarized plug with an extension cord receptacle or other outlets unless the prongs can be fully inserted. The display is designed to meet the medical safety requirements for a patient vicinity device. This device may not be used in connection with life support equipment. Underwriters Laboratories (UL) Classification:
UL safety Compliance:
This LCD monitor is U.L. Classified WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601-
1/CAH/CSA C22.2 NO. 601.1 6 - English English - 7 Servicing Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Unplug the apparatus from its power source and refer servicing to qualified personnel under the following conditions:
If the power cord or plug is damaged or frayed. If liquid has been spilled into the apparatus. If objects have fallen into the apparatus. If the apparatus has been exposed to rain or moisture If the apparatus has been subjected to excessive shock by being dropped. If the cabinet has been damaged. If the apparatus seems to be overheated. If the apparatus emits smoke or abnormal odor. If the apparatus fails to operate in accordance with the operating instructions. Accessories Use only accessories specified by the manufacturer, or sold with the apparatus. EEC Safety Compliance:
This display unit meets the requirements of EN-60601-1 so as to conform to the Medical Device Directive 93/42/EEC (general safety information). This monitor complies to the above standards only when used with the supplied medical grade power supply. JWM1150KA2400F04(Ault korea corp.) The monitor should be powered from a center tapped circuit when used in the US at voltages over 120 volts. Monitor is intended for continuous operation. This display is energized from an external electrical power source for class 1 equipment. It Is the responsibility of the installer to test the display's earth ground to verify that it complies with the hospital, local and nation impedance requirements. This requirement may not be used in the presence of flammable anesthetics mixture with air, oxygen or nitrous oxide. Recycling :
Follow local governing ordinances and recycling plans regarding the recycling or disposal of this requirement. Cleaning Instructions :
Follow your hospital protocol for the handling of blood and body fluids. Clean the display with a diluted mixture of mild detergent and water. Use a soft towel or swab. Use of certain cleaning agnts may cause degrandation to the labels and plastic components of the product. Consult cleanser manufacturer to see if agent is compatible with it. Do not allow liquid enter the display. 8 - English English - 9 Quick Startup Powering On The Unit :
1. Connect the power supply to the display via the power plug. 2. Plug in the DC adapter to AC inlet with power cord cable. 3. Connect the video source to this monitor. 4. Apply power to the peripheral device. 5. Turn on the switch of this monitor. FCC Information This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation. If this equipment is found to cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by carrying out one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the distance between the color monitor and the subject of interference. 3. Plug the monitor into a outlet on a different electrical circuit than that to which the subject of interference is connected. 4. Consult the dealer or an experienced radio/TV technician for help. NOTICES TO USER :
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation. FCC WARNING :
This equipement geneates or uses radio frequency energy. Changes or modifications to this equipement may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose authority to operate this equipment if an unauthorized change or modification is made. 10 - English English - 11 Parts Connector 24" LCD Monitor Back Panel Jacks Accessories User Manual D-SUB Cable AC Adapter S-Video (Y/C) Cable DVI Cable BNC Cable AC Power code
(Hospital Grade) DC Cable Terminal male / female (Option) SCREW FH M3X6
(Option) 12- English AC ON/OFF SWITCH AC Inlet OPTICAL IN DVI IN DVI OUT VGA IN RS232C SDI IN SDI OUT S-VIDEO/Y S-VIDEO/C C-VIDEO RED /Pr GREEN/Y BLUE/Pb C-SYNC/H-SYNC V-SYNC TOUCH(OPTION) English - 13 Mechanical Product Drawing Control OSD Button Position 14 - English English - 15 OSD Button Function An 8 button keypad, located in button light corner on the front of the display, allows the user to make adjustments to various display parameters using the On Screen Display (OSD) system. Power Indicating LED Green : Normal mode Red : Standby mode OFF : Monitor Off 6
- (MINUS) : With OSD deactivated, Hot key of the contrast control and decreases the contrast. With OSD activated, decreases the adjustment of the selected function. 7
+ (PLUS) : With OSD deactivated, Hot key of the contrast control and increase the contrast. With OSD activated, enter sub menu and increases the adjustment of the selected function. On-Screen Display (OSD) Function Button 8 INPUT : Change the display signal source. If D-SUB Analog's picture size not matched with full screen size or image is noisy press the input buttom during 2~3 seconds then you can see the most appropriate screen 1 2 3 4 POWER : Turns ON/OFF the monitor. MENU : With OSD deactivated, Activated to OSD menu. With OSD activated, Exit from main menu or sub menu. PIP : With OSD deactivated, Hot key of PIP mode. UP (
) : With OSD deactivated, Hot key of the brightness control and increases the brightness. With OSD activated, move the cursor upward. selected function. 5 DOWN (
) : With OSD deactivated, Hot key of the brightness control and decreases the brightness. With OSD activated, move the cursor downward. 16 - English English - 17 Power management Adjusting OSD This monitor does not adhere to the VESA DPMS standard when no signal is present on the video inputs. Status LED sign Power Consumption Normal Mode Green on <100W Standby Mode Red Blinking
<20W 18 - English ADJUST BRIGHTNESS CONTRAST SHARPNESS SATURATION COLOR BACK LIGHT 49 50 50 50 0 100 EXIT SELECT MOVE CVIDEO NTSC 60Hz/3.58MHz Adjust ADJUST BRIGHTNESS CONTRAST SHARPNESS SATURATION COLOR BACK LIGHT 49 50 50 50 0 100 EXIT SELECT MOVE CVIDEO NTSC 60Hz/3.58MHz 1 2 3 4 5 6 7 8 9 BRIGHTNESS Increase or decrease the brightness. (Range : 0~100) CONTRAST Increase or decrease the Contrast. (Range : 0~100) CLOCK Increase or decrease the sampling frequency.(Range : 0~100) PHASE Increase or decrease the Phase level.(Range : 0~100) BACK LIGHT Increase or decrease the back light dimming level (Range : 0~100) AUTO ADJUST Fit to the most appropriate screen on the D-SUB Analog signal SHARPNESS Adjust the sharpness of the displayed image. SATURATION Adjust the saturation of the image. COLOR Adjust the color of the image. English - 19 Color temp USER COLOR TEMP MODE RED GREEN BLUE 50 50 50 EXIT CVIDEO SELECT MOVE NTSC 60Hz/3.58MHz Image IMAGE IMAGE SIZE H POSITION V POSITION FILTER OVER SCAN FILL ASPECT 50 50 NORMAL 0 1 2 3 4 5 6 7 8 IMAGE SETTING MODE 1 EXIT CVIDEO SELECT MOVE NTSC 60Hz/3.58MHz 1 2 3 4 1 2 3 4 5 6 MODE Change the color model. (C1(Redish), C2(greenish). USER) RED Red balance (Only Working with USER mode) (Range : 0~100) GREEN Green balance (Only Working with USER mode) (Range : 0~100) BLUE Blue balance (Only Working with USER mode) (Range : 0~100) IMAGE SIZE Change the image size (Scaling mode)
(Full, Fill aspect, 1:1, Normal, Video, Zoom, video only) H POSITION Adjust the horizontal position of the displayed source image.
(Range : 0~100) V POSITION Adjust the vertical position of the displayed source image.
(Range : 0~100) FILTER Set the sharpness of image ( Softest, Soft, Normal, Sharp, Sharpest) OVER SCAN Adjust the displayed size. (0~8) IMAGE SETTING Allows selection of one of five user defined image presets. Setup SETUP LANGUAGE OSD COLOR OSD POSITION DURATION RESET SETTINGS ENGLISH 20 SEC 50 AUTO SOURCE SELECT ON EXIT CVIDEO SELECT MOVE NTSC 60Hz/3.58MHz PIP PIP LAYOUT SOURCE SWAP PIP COMPONENT EXIT CVIDEO SELECT MOVE NTSC 60Hz/3.58MHz 1 2 3 4 5 6 1 2 3 LANGUAGE Change the OSD language (8 language)
(Korean, English, French, Spanish, German, Chinese, Japanese, Italian) OSD COLOR Adjust the OSD background from white opaque to half translucent. OSD POSITION Change the osd position. (9 Positions) DURATION Adjust time until the OSD Menu will disappear after adjusting the menu.
(5, 10, 20, 30, 60, 90, 120, 180, 240 seconds) RESET SETTINGS Changes the all OSD value to factory out going status. AUTO SOURCE SELECT Disable of enable auto source select.
(ON: Searches through all possible input source untill an active video source is found. OFF: Video input is manually selected.) LAYOUT Change the OSD layout. (Single, PIP, PBP1, PBP2) SOURCE Change the secondary source. SWAP Swaps the position and size of the Primary and Secondary image. 20 - English English - 21 Standard Signal table Signal connector Pin Assignments PC Supported Mode Resolution Horizontal Frequency
(KHz) Vertical Frequency
(Hz) Clock Frequency
(MHz) 640 X 350 @70Hz 720 X 400 @70Hz 640 X 480 @60Hz 640 X 480 @75Hz 800 X 600 @60Hz 800 X 600 @75Hz 1024 X 768 @60Hz 1024 X 768 @75Hz 1152 X 864 @60Hz 1152 X 864 @75Hz 1280 X 1024@75Hz 1360 X 768@75Hz 1600 X 1200@60Hz 1920 X 1080@60Hz 1920 X 1200@60Hz 31.469 31.469 31.469 37.500 37.879 46.875 48.363 60.023 54.348 67.500 79.976 47.649 74.077 67.500 74.099 70.087 70.082 59.940 75.000 60.317 75.000 60.004 75.029 60.053 75.000 75.025 59.936 59.981 60.000 59.999 25.175 28.324 25.175 31.500 40.000 49.500 65.000 78.750 80.000 108.000 135.000 84.625 130.375 148.500 154.125 SDI Video format Output Signal SMPTE-274M Description 1080i (60 / 59.94 / 50) 1080p (30 /29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF) SMPTE-296M 720p (60 / 59.94 / 50) SMPTE-260M 1035i (60 / 59.94) SMPTE-125M 480i (59.94) ITU-R BT.656 576i (50) 22- English VGA (15Pin D-Sub) Pin No. Assignment Pin No. 1 2 3 4 5 6 7 8 Red Green Blue Ground DDC 5V Standby Cable Connection check Ground-Red Ground-Green Ground-Blue 9 10 11 12 13 14 15 Assignment No Connection Ground-Sync Ground DDC Data H.Sync V.Sync DDC Clock 1 5 6 10 11 15 DVI In,Out (24Pin DVI-D) Pin No. Assignment 1 2 3 4 5 6 7 8 9 10 11 12 T.M.D.S. Data2-
T.M.D.S. Data2+
T.M.D.S. Data2 Shield No Connection No Connection DDC Clock DDC Data No Connection T.M.D.S. Data1-
T.M.D.S. Data1+
T.M.D.S. Data1 Shield No Connection Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Assignment No Connection
+5V Power Cable Connection check Hot Plug Detect T.M.D.S. Data0-
T.M.D.S. Data0+
T.M.D.S. Data0 Shield No Connection No Connection T.M.D.S. Clock Shield T.M.D.S. Clock+
T.M.D.S. Clock-
C-Video (BNC) Pin No. 1 2 Assignment Composite Ground 1 8 9 16 17 24 1 2 English - 23 S-Video (BNC) Pin No. 1 2 3 Assignment S-VIDEO/Y (Luma) S-VIDEO/C (Chroma) Ground RS232C (D-SUB 9Pin) Pin No. 1 2 3 4 5 6 7 8 9 SDI (BNC) Pin No. 1 2 3 24 - English Assignment No Connection TXD RXD No Connection Ground No Connection No Connection No Connection No Connection Assignment SDI IN SDI OUT Ground 3 RGBHV/RGBS/YPbPr (BNC) 6 1 2 Pin No. 1 2 3 4 5 6 Assignment RGBS Red Green Blue Y Pb Pr Pr Y Pb H-Sync / C-Sync No Connection No Connection V-Sync Ground R/Pr 1 G/Y 2 B/Pb CS/HS 3 4 VS 5 OPTICAL Pin No. 1 2 3 4 Assignment OPICAL Clock OPICAL Blue OPICAL Green OPICAL Red 1 2 3 4 1 5 6 9 3 1 2 English - 25 Specification Model LCD Panel Synchro nization Power Consumption Control key Input Signal Out Signal Type Screen Size Maximum Resolution Pixel pitch Display Colors Contrast Ratio Viewing Angle Response Time Luminance Horizontal Frequency Vertical Frequency Maximum Standby Mode Front side Video Video FS-L2401D TFT-LCD 24 linch 1920 X 1200 @ 60Hz 0.270(H) mm X 0.270(V) mm 16.7M 700:1 89 / 89 / 89 / 89 12 msec(Rising+Falling) 400cd/m 30KHz~75KHz 50Hz~75Hz Max 100W Max 20W INPUT, -, +, 1XDVI, 1XOptical DVI, 1XD-SUB, 1XBNC (CVBS) 2XBNC (SVHS Y/C), 1XBNC (SDI), 5XBNC
(Component Y/G, Pb/B, Pr/R, H/CS, VS Input) 1XDVI, 1XBNC (SDI)
, PIP, MENU, POWER
, Input power DC 24V, 6.25A Max Dimension Size and Weight 580 386 87.5(mm)/ 10Kg 26 - English