BLUETOOTH EARPHONE PT-WE001 USER MANUAL Read this user manual carefully before using the product. Technical Specications :
Bluetooth version: 5.0 Working time : 3 hours Charging time : 2 hours Battery type : Lithium Polymer 3.7V/55mAh/
Wireless distance : 10 m Working Frequency : 2,402-2,480GHz Speaker diameter: 9mm Software and version:V1 Input: DC 5V , 1A Turn on/off Long press the function button for 2s-4s to turn on the earphone . You can hear voice prompt power on . Long press the function button for more than 4s to turn off the earphone . You can hear voice prompt power off . A B C Short press:
next song Long press(more than 2s) volume up Short press:music on,pause,power on/off Press twice: redial last call D Short press:
previous song Long press(more than 2s) volume down A B C D MIC / Volume Up / lndicator Light ON / OFF Volume Down Micro USB Charging Port Charging Charge port 5V1A The indicator light turns red when charging . The indicator light turns blue when earphone is fully charged . Pairing Pair the device at the rst time :
1. Long press the function button for 2s-4s to turn on the earphone and enter into pairing mode
( you can hear the prompt voice of pairing and see the red and blue indicator light ashing alternately ) . 2. Search the bluetooth device PT-WE001 to connect . 3. You can hear voice prompt connected. Then you can enjoy music and make phone calls. BLUETOOTH EARPHONE PT-WE001 Listen Music Short press button+: next song . Long press ( more than 2s) button+: volume up Short press button- : previous song Long press ( more than 2s) button-: volume down Short press function button: play/pause song ; power on/power off Double press function button: redial last call Answer a call There comes a call when listening music :
Short press function button to pause music and answer the call ;
Short press the function button again to hang up the call and play the music ;
When call comes in :
Short press the function button to answer the call ;
Long press the function button for 2s to refuse the call . Cleaning in the United States If necessary , clean the earphones with a damp cloth and let it dry completely before use . Do not use any solvents, corrosive or gaseous cleaning agents . Make use no water or other liquids penetrate the housing .The full text of the EU declaration of conformity is available at the following internet address:
http://dataplusgo.com/uploads/PT-WE001.jpg PANTONE and the PANTONE Chip Design are trademarks of Pantone LLC and/or in other countries. Pantone LLC, 2020. All rights reserved. This is an authorized PANTONE product manufactured under license by DATAplus Supplies,Inc. 2020 DATAplus Supplies, Inc. registered in Taiwan. All products are designed by DATAplus and used under license. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.