ZJ21O Product Description Part 1. Quick Start Guide Get more help at http://www.cloudhawkgps.com/help Step 1: User Registration 1. Access website (http://www.mycloudhawk.com) or open CloudHawk mobile app (download them from Google Play or App Store). 2. Click Setup New Account, type in your email address and click Register. 3. Check your email and follow the link to complete the registration. Step 2: Device Activation 1. Add new device on web site a. Sign in to website (www.mycloudhawk.com) with the registered account;
b. Click the + button below your tracker list;
c. Type in the Activation Code and the tracker's Serial Number (S/N) and click Add. The activation code can be found on the package label or in the User Manual. The tracker SN can be found on the label at the bottom of the device. 2 2. Enable the device a. Open the device, plug in your SIM card and turn on the device. Put micro SIM card inside as this way Slide the switch on to turn on device as the picture b.The indicator will light steady yellow then go to rapidly ash yellow. When it goes to steady yellow again for 10 seconds, the device is ready to use. 3 Step 3: Customize settings After signed into your account, you can customize your settings to meet your specic needs, such as setup your tracker's name, geo-fences, notications or share the tracker to your family/friends. Congratulations!
Your CloudHawk tracking device is ready to use!
4 Part 2. User Manual Get more help at www.cloudhawkgps.com/help 1. ZJ 210 Overview Reset button and LED indicator Tracker information:
Dimensions Technologies Battery Voltage supply SIM card type Interface connector
* In good GPS signal conditions
** 95% CEP, i.e., accuracy of 95% of the xes are within the listed limit 73*54*21mm GSM quad band /GPRS, GPS, A-GPS Lithium-ion battery 220mAh 12-60V DC Micro SIM card 6 1.VCC,12-60V DC positive inpute 2.GND,12-60V DC negative inpute 3.No used 4.No used 5.ACC,after motors swith 6.Postive wire of buzzer 5V DC out
* Connect the device to motor as the picture above. 7 3. LED Indicator Status Table Condition Normal operation Initializing Upgrading rmware Connecting to server Connected to server Service not available SIM-card error Charging, low battery capacity Charging, normal battery capacity Charging, battery near full capacity Charging, full battery Sending emergency message Searching GPS signal during status check GPS signal normal during status check GPS signal low during status check 8 LED color pattern None Steady Yellow Green double ash Yellow fast ash Yellow for 10 seconds Yellow double ash Red double ash Red slow ash Yellow slow ash Green slow ash Steady Green Red fast ash Green fast ash Green for 10 seconds Red for 10 seconds 4.FAQ Fail to boot-up Charging fails Tracker off-line GPS positioning failure when rst use GPS positioning failure The power might be low, please try charging through VCC and GND (check the connection mode in page x). Please check the connection between the batter y and the device, and ensure there is no damage on VCC or GND. If the indicator is off, please reboot the device manually by long pressing the reset button. Please place the device under an open sky condition during initial boot-up, and wait 5 minutes for it to acquire an initial position. This only needs to be done once. If the device is indoor or in an underground parking, please take it to an area which has an unobstructed view of the sky. If it locates beneath the metal shield, please remove the shield or change the install position. 9 FCCWARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the followingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmay causeundesiredoperation. NOTE1:Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfora ClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesigned to provide reasonable protection against harmful interference in a residential installation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergy and,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful interference to radio communications. However, there is no guarantee that interferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferencebyoneormoreofthefollowingmeasures:
Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe receiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.