FCC ID: 2AK29-DS2011 Master Smart Dimmer

Deako Smart Dimmer Single Pole Smart Dimmer Master Smart Dimmer Remote Smart Dimmer Get to know your Deako Switch 22 Main button Configure button LED indicators Dimmer control 33 LED key LED key LED COLOR WHAT IT MEANS Blinking green Powering up Blinking purple Linking mode Blinking blue Pairing mode Blinking white Pairing or Linking 44 LED COLOR WHAT IT MEANS Solid white Pairing or Linking successful Blinking red Error occured, try again Solid red Factory resetting 55 How many switches control this light?

66 1 switch 2+ switches If one switch controls this light, CONTINUE TO PAGE 8 If two or more switches control this light, TURN TO PAGE 12 77 Insert a switch 1 Align the blue tab on the backplate with the top of the switch 88 2 While pressing the switch inwards, push in the blue tab 99 Installation complete!

Now lets get smart. 1010 Pairing Control your new smart switch by downloading the Deako App. 1111 What youll need 1212 1x master dimmer 1+ remote dimmer One master dimmer One remote dimmer for each additional switch location 1313 Switch types Identify the switch type by looking at the sticker found on the back of your switch. You will either have a Master Smart Dimmer or Remote Smart Dimmer. If you have a different type of switch, go to support.deako.com for more information 1414 9696669209165087 9696669209165087 1515 Remove existing dimmer Remove existing dimmer 1 If there is a switch installed in the backplate you want to upgrade, start by pulling the corner of the faceplate 1616 2 Pull the blue tab outwards to release the switch 1717 Insert Remote Dimmer Insert Remote Dimmer 3 Locate the powered backplate in the circuit by inserting a Remote Smart Dimmer into a backplate in the circuit Align the blue tab on the backplate with the top of the switch 1818 4 While pressing the switch inwards, push in the blue tab If the backplate is powered, green the switch will flash If switch does not flash green, move to the next location & repeat step 1 1919 5 Wait until the switch stops flashing green, then press &

hold the configure button until it flashes purple 2020 6 Move to the next powered backplate, then repeat steps 1-5 for each switch in the circuit until you get to the last switch 2121 Insert Master switch Insert Master switch 7 On the last switch in the circuit, insert the Master Smart Dimmer 2222 8 Wait until the switch stops flashing green, then press &

hold the configure button until it flashes purple Once all switches in the circuit are flashing continue to step 9 purple, 2323 9 Once all switches in the circuit are flashing purple, press & hold the configure button on any white switch until it flashes Once the switches show solid white and turn off, linking is complete 2424 10 To test if theyve been successfully linked, press each switch to confirm that they control the light Now youre ready to pair your switches with the Deako App 2525 Troubleshooting Linking is only required for 3-way and 4-way wiring configurations If at any point a switch blinks red, factory reset it and try again To exit linking mode at any point, press & hold the configure button for 10 seconds to factory reset each switch before retrying If you have dead-end or other nontraditional wiring in your home, you can find wiring and setup instructions at deako.com/wiring 2626 Factory reset Press & hold the configure button for 10 seconds (the LED will be appear solid red). 2727 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

-Consult the dealer or an experienced radio/TV technician for help. connected. RF warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC Statement

-English: This device contains licenceexempt transmitter(s)/receiver(s) that comply with Innovati on, Science and Economic Development Canadas licenceexempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B) This device must be installed and operated with a minimum distance of 20 cm between the radia tor and user body.

-French: L'metteur/rcepteurexempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation. Sciences et DveloppementconomiqueCanada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si e brouillage est susceptible d'en compromettre le fonctionnement 'appareil numrique du ciem conforme canadien peut -3 (b)/nmb -3(b). Cet appareil est conforme l'exemption des limites d'valuation courante dans la section 2.5 du cnr - 102 et conformit avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des donnes canadiennes sur l'exposition aux champs rf et la conformit.This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Cet quipement est conforme aux limites d'exposition aux rayonnements de la IC tablies pour unenvironnement non contr. Cet quipement doit tre install et fonctionner au moins 20cm de distance d'un radiateur ou de votre corps. Cet metteur ne doit pas tre co-localis ou fonctionner en conjonction avec une autre antenne ou un autre metteur. Need help?

Need help?

support.deako.com 1-844-673-3256

CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel: +86-755-27521059 Fax: +86-755-27521011 Http://www.sz-ctc.org.cn Label Label Location 1.

Deako Inc. Date: 2021.04.28 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID:__2AK29-DS2011 ____ Product Name:__Master Smart Dimmer ________ Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ) Schematics Block Diagram Operation Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature:

Name: Derek Richardson Company: Deako Inc. Address: 4201 Roosevelt Way NE Suite 100 Seattle WA 98105 United States Phone: 1-844-67-33256 Fax: /

Mail: dxr@deako.com