3/8. Dynamic Speed Adjust Adjust dynamic playing speed. Press Speed + to increase speed and press Speed - to decrease speed Unit will switch to dynamic mode If press this key at stac color mode. 4/5. Static Color Adjust Switch to stac color mode from dynamic mode, or switch between dierent stac colors. 6/7. Brightness Adjust Adjust stac color brightness. Press Bright + to increase brightness and press Bright - to decrease. Unit will switch to staic color mode If press this key at dynamic mode. Functions LB NO.DC-RGBRTFCC RF Wireless Remote RGB LED Controller Instructions 21 Dynamic Modes 21 Stac Colors 256-Grade PWM Speed Adjustable Brightness Adjustable Card Type Remote Ultra Slim Design Demo Mode 1 to 1 Remote Paired Auto Save Funcon 1. Turn On/Standby Press this key to turn on unit or switch to standby mode. Unit will turn on and restore to previous status at powering on moment. 2/9. Dynamic Modes Adjust Switch to dynamic mode from stac color mode, or switch between dynamic modes. 10. Demo Mode Press this key will swith to Demo mode. At demo mode, it will loop play 9 dynamic modes, each mode repeat 3 mes. Installing 1. Power Supply This unit accepts DC 12V to 24V power supply. The inner pole polarity is posive and sleeve is negave. Please select proper power supply according to the LED applicaon. 2. LED Output This unit support common anode connecon LED products. The mark indicates the common connecon node. The peak output current is 4A per channel, please reduce load if main unit is overheang. CAUTION! Do not short circuit the LED output, this may lead to permanent damage!
Battery GND 3. Remote Controll Please pull out the insulate part before using. The RF wireless remote signal can pass through barrier, so its not necessary to aim at the main unit when operate. For proper receiving remote signal, do not install the main unit in closed metal parts. The remote baery is 3V CR2025 type, please only replace with same type baery. Specication Dynamic mode Stac Color PWM Grade Brightness Grade Speed Grade Demo mode Working Voltage Output Current Remote frequency Remote distance 21 modes 21 colors 256 levels 8 levels 8 levels Yes DC 12~24V 3-way, peak 4A per channel 433.92MHz
>20m at open area Notice:
This controller can only work within 5V, 30W. Therefore please do not aach more than 4 meters long led light strip to the controller when using it in order to avoid overload danger.
- English: "
This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is subject to the following two condions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operaon of the device."
- French: "
Leprsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaon est autorise aux deux condions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'ulisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est suscepble d'en compromere le fonconnement."
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC RF Exposure The device has been evaluated to meet general RF exposure requirement. The device can be used in portable condition without restriction.