QUICK SETUP GUIDE Data Collector Data Collector connects your PV Micro Inverter System to the internet in a simple quick way. It uses ZigBee wireless radio frequency communication technology to monitor each micro inverter without additional wiring. Through Web Portal, you can check data on the daily and historical photovoltaic energy harvest. Safety and Accident Prevention The equipment has been manufactured in accordance with the strictest accident-prevention regulations and supplied with safety devices suitable for the protection of components and operators. Deleco accepts no liability for failure to comply with the instructions for correct installation and cannot be held responsible for the systems upstream or downstream of the equipment it has supplied. It is essential to provide the operators with correct information. They must read and comply with the technical information required in the manual and in the attached documentation. The instructions given in this SETUP GUIDE does not replace the safety devices and technical data for installation and operation stuck on the product, and they certainly do not replace the safety regulations in force in the country of installation and common sense rules. The manufacturer is willing to train staff, at its premises or on site, in accordance with conditions to be set out in the contract. Avoid temporary fixes. All repairs should be carried out using only genuine spare parts, which must be installed in accordance with their intended use. Liabilities arising from commercial components are delegated to the respective manufacturers. The equipment must be installed indoors in rooms with suitable environmental conditions. The equipment is not equipped to operate in environments that have particular flammable or explosive conditions. In order to prevent signal collision in Micro Inverter Monitoring System, only ONE Data Collector installed is permitted. (More than TWO Data Collectors installed in Micro Inverter System could cause signal collision problem!), and up to 32 micro inverters can be directly monitored by a single Data Collector. There is a hazard voltage inside this equipment and no maintainable parts inside this equipment. Do not use the equipment if you find any anomalies while it is operating. Federal Communication Commission Interference Statement This device complies Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Pursuant to IEC60950, the Data Collector involves technologies and materials or methods provide a level of safety. Any modifications or changes made to this equipment may void the user warranty. Overview This diagram shows the relationship between Data Collector and other devices. For Micro Inverter Monitoring System, the Data Collector communicates with your Micro Inverter System via wireless, the communication quality is depended on your actual installation environment. (The shortest distance between Data Collector and Micro Inverters is preferred!) Data Collector Key Parts Description 01: ZigBee antenna 04: Keypad (touch pad) 07: RESET button 10, Spec. Label 02: Status LED (under the plastic cover) 05: Ethernet port 08: AC inlet 11: Rubber foots 03: OLED Display 06: Ethernet status LED 09: Wall mount holes 03 01 02 04 Keypad Description There are 3 touch pads (Keypad) provide the various functionalities.
The MENU button
: shows menu and returns to 11 previous sub-menu when navigating.
The DOWN button
The SELECT button
: moves cursor down.
: similar to enter. 06 05 07 10 09 08
Data Collector Serial Number
ETHERNET communication MAC address
Wi-Fi communication MAC address
ZigBee MAC address The Spec. Label attached to the Data Collector must not be removed, damaged or dirtied, etc. The technical data shown in this manual does not in any case replace those shown on the Spec. Label attached to the Data Collector. Page XX Page XX or Step 2:
Setup via Wireless Step 2:
Setup via Ethernet Cable Step 1:
Power on the Data Collector Data Collector Setup (No Internet Environment Available) Setup Process Flow Chart Step 1:
Power on the Data Collector Once you plug in the AC power cord you will see the Wi-Fi DEVICE and ETHERNET DEVICE message shown on the Data Collector OLED Display. (Press RESET button can get the same result.) Step 3:
Web Registration Procedure Step 4:
DIN Rail Mounting Page XX Page XX Page XX RESET button
> Wi-Fi DEVICE
> ETHERNET DEVICE There are two approaches to set up a Data Collector device. The type of connection can be setup via:
<1> Ethernet Cable - Set Data Collector as an Ethernet device.
<2> or Wirelessly - Set Data Collector as a Wi-Fi device. Step 2:
Setup via Ethernet Cable System configuration shown as below On Data Collector OLED Display DOWN ->
SELECT)
> Wi-Fi DEVICE Choose ETHERNET DEVICE (
> ETHERNET DEVICE Please connect Data Collector and your computer via an Ethernet Cable. Please skip to the Web Registration Procedure. You can press the RESET button if you want to redo the setup. Step 2:
Setup via Wireless (Using Wi-Fi Signal) System configuration shown as below On Data Collector OLED Display Choose Wi-Fi DEVICE ( SELECT)
> ETHERNET DEVICE
> Wi-Fi DEVICE Please connect your computers Wi-Fi to the SSID DELTA_XXXXXXXXXXXX Please skip to the Web Registration Procedure. You can press the RESET button if you want to redo the setup. Step 3:
Web Registration Procedure In Your PC Side Open the web browser, key-in IP address 169.254.0.1 as shown on the Data Collector OLED Display to enter Data Collector embedded web page. The screen should now show the setup page, click on Scan Device. This is system default and may be different from what is shown on your screen. Then, press the Start button to search all micro inverters which you have installed. Then, press the Stop button to stop searching when all micro inverters have found. Otherwise, it will keep searching until 20 minutes time out. After stopping, please disable the devices to kick out those micro inverters that do not belong to you. Then, press the Confirm button to finish scan device procedure. After confirming, you can see the list of series number and MAC address from your micro inverters. Then click the Setting The popup window show Data Saved Finish and click OK. PLEASE AWAIT CONFIG The message PLEASE AWAIT CONFIG will be displayed on the Data Collector OLED Display. The xx:xx time count is depending on how many micro inverters that you registered on your Data Collector. Step 4:
DIN Rail Mounting Skip to the DIN Rail Mounting Procedure. XX:XX Page XX Page XX Page XX or Step 2:
Setup via Wireless Step 2:
Setup via Ethernet Cable Step 1:
Power on the Data Collector Data Collector Setup (Internet Environment Available) Setup Process Flow Chart Step 1:
Power on the Data Collector Once you plug in the AC power cord you will see the Wi-Fi DEVICE and ETHERNET DEVICE message shown on the Data Collector OLED Display. (Press RESET button can get the same result.) Step 3:
Web Registration Procedure Step 4:
DIN Rail Mounting Page XX Page XX RESET button
> Wi-Fi DEVICE
> ETHERNET DEVICE There are two approaches to setting up a Data Collector device. The type of connection can be setup via:
<1> Ethernet Cable - Set Data Collector as an Ethernet device.
<2> or Wirelessly - Set Data Collector as a Wi-Fi device. Step 2:
Setup via Ethernet Cable System configuration shown as below Please make sure your PC can access the internet. Please make sure AP/Router has enable the DHCP service. On Data Collector OLED Display DOWN ->
SELECT)
> Wi-Fi DEVICE
> ETHERNET DEVICE Choose ETHERNET DEVICE (
After a while, the IP address will be shown on Data Collector OLED Display.
(This IP address is assigned by the AP/Router.) In Your PC Side Open the web browser, key-in IP address as shown on the Data Collector OLED Display. TTL ENERGY: XX.XkWh 192.168.X.X The screen should now show the setup page, click on Scan Device. Then, press the Start button to search all micro inverters which you have installed. This is system default and may be different from what is shown on your screen. Then, press the Stop button to stop searching when all micro inverters have found. Otherwise, it will keep searching until 20 minutes time out. After stopping, please disable the devices to kick out those micro inverters that do not belong to you. Then, press the Confirm button to finish scan device procedure. After confirming, then, click I Accept button.
(Now, the Data Collector device should be set as an Ethernet device.) Please skip to the Web Registration Procedure. You can press the RESET button if you want to redo the setup. Step 2:
Setup via Wireless (Using Wi-Fi Signal) System configuration shown as below Please make sure your PC has access to internet. Please make sure AP/Router has enable the DHCP enabled.
> Wi-Fi DEVICE
> ETHERNET DEVICE On Data Collector OLED Display Choose Wi-Fi DEVICE ( SELECT) The OLED Display will alternatively show the IP address, date and time. 00/00/0000 00:00:00 TTL ENERGY: XX.XkWh TTL POWER: X.XW 169.254.0.1 Once you finished the setup, the Time and Date will be updated automatically via the internet. Antenna has directivity it should facing to Wi-Fi Router and PC. Please connect your computers Wi-Fi to the SSID DELTA_XXXXXXXXXXXX Open the web browser and key-in the IP address as shown on Data Collector OLED Display. Click on Configure Network. The screen will display two options; click Scan Wireless Networks. This is system default and may be different from what is shown on your screen. You should now see your Wi-Fi router will be listed. Choose the SSID corresponding to your Wi-Fi Router. (Password maybe needed if your AP/Router has encryption) Step1 A confirmation message should be displayed as shown below. Step2 After a certain timeframe, the IP address will appear on the Data Collector OLED Display.
(This IP address is assigned by your Wi-Fi Router, it maybe different from this SETUP GUIDE) Please reconnect your computers Wi-Fi to your original internet connection. TTL ENERGY: XX.XkWh 192.168.X.X Web Step2 Open the web browser; key-in the IP address as shown on the Data Collector OLED Display. Step1 The screen should now show the setup page, click on Scan Device. Then, press the Start button to search all micro inverters which you have installed. This is system default and may be different from what is shown on your screen. Then, press the Stop button to stop searching when all micro inverters have found. Otherwise, it will keep searching until 20 minutes time out. After stopping, please disable the devices to kick out those micro inverters that do not belong to you. Then, press the Confirm button to finish scan device procedure. After confirming, then, click I Accept button.
(Now, the Data Collector device is settled as a Wi-Fi device.) Skip to the Web Registration Procedure. You can press the RESET button if you want to redo the setup again. Step 3:
Web Registration Procedure Once you click the I Accept, the web page will be redirect to our Deleco EMS sign up. Sign up for new account. Register your detailed personal data and click SUBMIT. The page should then confirm your registration. Click here to login. Login with the user account and password you registered. You can see the list of series number and MAC address from your micro inverters. Then click the NEXT The popup window show I have confirmed the series number and click OK. Register the Data Collector name, time zone and location. Confirm the Data Collector information, then click SUBMIT button. You will receive a confirmation of the completion of your registration. The message PLEASE AWAIT CONFIG will be displayed on the Data Collector OLED Display. The xx:xx time count is depending on how many micro inverters that you registered on your Data Collector. PLEASE AWAIT CONFIG XX:XX Step 4:
DIN Rail Mounting It is advisable to undertake all the configuration operations before fixing the Data Collector and installing it in the same location and position used during the configuration. Also choose a place close to a socket
(necessary for power, close to PV System) and where the lower part of the device, where all the connections are present, remains accessible. Bracket DIN Rail To install the Bracket on DIN Rail, please follow the steps below. 1. Clip the top side of the Bracket on the top side of the DIN Rail first. 2. Push the bottom of the Bracket to snap on the bottom side of the DIN Rail. 3. Hang the Data Collector on the Bracket on DIN Rail. Step 2 Step 1 To release the Bracket from DIN Rail, please follow the steps below. Step 3 Step 1. Take out the Data Collector from the Bracket on DIN Rail. 2. Insert a flathead screwdriver into the rectangular slot and turn it downward to release the clip from the DIN Rail. 3. Remove the Bracket from the DIN Rail. Step 1 Step 2 Step 3 Released The installation must be done by qualified installers and/or licensed electrician according to the applicable local regulations. The connection of Micro Inverter System to the electricity distribution network must be approved by the appropriate electrical distributor. The installation must be carried out while the equipment is disconnected from the grid. Grid Code Setting Once you finished the Micro Inverter registration process, then you MUST do the Grid Code Setting. It is the responsibility of the installer to follow local installation regulations and guidelines in accordance with local electrical codes and Nation electrical codes for electrical installation as specified by the Clean Energy Council. Step 1: Find the IP address shown on your Data Collector OLED display. (Note: The IP address depends on your network environment. Step 2: In your PC side, open your web browser, and key-in the IP address as shown on Data Collector. Then, enter the Data Collector embedded web page. TTL ENERGY: 0.0kWh 169.254.0.1 Step 3: Add the #1234 after the IP address. Step 4: Read the warranty and click Continue. Step 5: Enter the setting grid code page. Step 6: Setting your grid code and Submit. Structure of the OLED Display Menu The buttons MENU OLED Display.
, DOWN and SELECT are used to explore the menu on the 192.168.X.X TTL ENERGY xx.x kWh 13/01/2001 01:01:01 TTL POWER x.x W During the normal operation of the Data Collector & Micro Inverters, the OLED Display is shown as left.
(Toggle displays every ~10 sec.) Press MENU button By pressing MENU informative screens about the Data Collector. button during the normal operation, you can access the set up and OLED CONFIG DATE/TIMING SET UP OLED CONFIG POWER ALWAYS ON POWER SAVE MODE DATE/TIMING SET UP DATE: dd/mm/yy TIME: 00:00:00 DST CONFIG LCD DISPLAY CONFIG DST CONFIG LCD DISPLAY CONFIG POWER DISPLAY TYPE RSSI DETECT POWER DISPLAY TYPE WPS START EXIT MENU RSSI DETECT WPS START EXIT MENU ENABLE DISABLE POWER DISPLAY STATUS DISPLAY TOTAL INDIVID. (30 sec)