Flashlink RTL 22362 User Manual 1 Content 1.Purpose .......................................................................................................................................................... 3 2. General Specification ............................................................................................................................... 3 3. LED instructions. ...................................................................................................................................... 3 4 Key function instructions ........................................................................................................................ 4 2 1.Purpose This report is used to calculate the relevant test results of 22362 temperature monitor. 2. General Specification B9D Single-use Internal digital temperature sensor Item Usage Type Sensor Accuracy Resolution SIM Card Shelf Life Connector Memory Capacity 28800 readings Measurement Range
-20C ~ 70C (-4F ~ 158F) 0.5C/0.9F ( -10C-45C )1C (Other) Cellular Communications 2G: GSM (850, 900, 1800, 1900 MHz) Internal Embedded (Global Data Roaming) 0.1 1 Year USB 2.0 1 2 3 4 3. LED instructions. NO Test item Test method Judge standard LED toggle red/blue twice Pass LED in Idle Mode Press start button for 1 second when the power of the logger is normal Press start button for 1 second when the power of the logger is low Press and hold Flight button for 5 seconds Press and hold start button for 5 seconds then logger from Idle mode to Recording mode No LED light under any condition No LED light and logger can not enter Flight Mode The status LED flash Blue every 10 seconds for 30 minutes to indicate it has started properly After 30 Result Pass Pass Pass 3 minutes this flash sequence will stop NO Test item Test method Judge standard LED in Mode 6 Recording 5 7 Press start button for 1 second when the power of the logger is normal Press start button for 1 second when the power of the logger is low press Flight button for 1 second Blue flash indicates logger is recording No flash means low battery (no LED) Battery is dead No Flash means logger is not enable Flight Mode NO Test item Test method Judge standard 8 9 10 LED in Flight Mode Press and hold Flight button for 5 seconds then logger from Recording Mode to Flight Mode Singlepress Flight button for 1 second and a Red LED light indicates Press and hold flight mode button for 5 seconds Flight Mode LED blink Red LED 5 times to indicate logger has entered Flight Mode Red LED light indicates it is in flight mode Red LED go solid for 5 seconds and exit Flight Mode 4 Key function instructions NO Test item Test method Judge standard 1 Start Press and hold start button for 5 seconds enable logger to record data Logger data upload to platformread interval is 5mins and report interval is 15 mins NO Test item Test method Judge standard 2 Flight Mode In Recording ModePress and hold Flight button for 5 seconds enable logger to Flight Mode Logger continue to record data but will stop uploading data to platform until it exit Flight Mode Result Pass Pass Pass Result Pass Pass Pass Result Pass Result Pass 4 press and hold Flight button for 5 seconds exit Flight Mode after logger in Flight Mode for 12 hours platform and device data are not lost Pass NO Test item Test method Judge standard Stop In recording mode connect usb cable to logger In Flight Mode Connect usb cable to logger logger stop then user can view PDF or export PDF to PC logger will stop then user can view PDF or export PDF to PC Result Pass Pass 3 4 5 5 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body.