FCC ID: HYQDNMWR004 MILLIMETER WAVE RADAR SENSOR (76GHz VEHICLE MOUNT)

1.1.3. Manual Requirement of FCC / IC Our product (DNMWR004) is one of vehicle parts incorporated into the vehicle as original equipment. Therefore, we will not supply the users manual and service manual of the product. However, we will ask the vehicle manufacturer to include following statements in the vehicle users manual and service manual in accordance with FCC and IC requirements. 1. Requirement for User Manual 1.1. FCC Requirement 1.1.1. 1.1.2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. In accordance with 15.21 of FCC rule, following statement will be included in the users manual. In accordance with requirement of FCC RF exposure, following statement will be included in the users manual. FCC WARNING Radiofrequency radiation exposure Information:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator (antenna) and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In accordance with requirement of FCC15.19(a)(5), following statement will be included in the users manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. 1.2. IC Requirement 1.2.1. In accordance with requirement of RSS-Gen, following statement will be included in the users interference including 1.2.2. In accordance with requirement of RSS-102, following statement will be included in the users This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. manual. manual. Radiofrequency radiation exposure Information:

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Radiofrequency radiation exposure Information:

2. Service manual In accordance with SAR requirement of FCC and IC rules, following statement will be included in the users manual. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be kept with minimum distance of 20 cm between the radiator (antenna) and your body at all times during adjustment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

1.1.3. Manual Requirement of FCC / IC Our product (DNMWR004) is one of vehicle parts incorporated into the vehicle as original equipment. Therefore, we will not supply the users manual and service manual of the product. However, we will ask the vehicle manufacturer to include following statements in the vehicle users manual and service manual in accordance with FCC and IC requirements. 1. Requirement for User Manual 1.1. FCC Requirement 1.1.1. 1.1.2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. In accordance with 15.21 of FCC rule, following statement will be included in the users manual. In accordance with requirement of FCC RF exposure, following statement will be included in the users manual. FCC WARNING This device complies with the FCC RF exposure requirements. FCC RF exposure Information manual. In accordance with requirement of FCC15.19(a)(5), following statement will be included in the users manual. This device complies with Part 15 of the FCC Rules and RSS-210. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1.2. IC Requirement 1.2.1. In accordance with requirement of RSS-Gen, following statement will be included in the users interference that may cause undesired operation of the device. Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference received, including 2. Service manual In accordance with SAR requirement of FCC rule, following statement will be included in the users manual. Caution: Radio Frequency Exposure This device complies with applicable FCC radio frequency exposure requirements, and must be adjusted with a distance of at least 20cm

(7.9 inches) between the RF aperture of device and the body of any person at all times during adjustment. FCC WARNING FCC RF exposure Information This device complies with the FCC RF exposure requirements. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. To: XXXXXXXXXXXXXXX The following statements are FCC and IC requirements for users manual and service manual. Therefore, the following statements must be included in users manual and service manual. Please include the following statements in your users manual and service manual. 1. Requirement statement for users manual 1.1. FCC Requirement 1.2. IC Requirement 2. Requirement statement for service manual Caution: Radio Frequency Exposure This device complies with applicable FCC radio frequency exposure requirements, and must be adjusted with a distance of at least 20cm (7.9 inches) between the RF aperture of device and the body of any person at all times during adjustment. This device complies with Part 15 of the FCC Rules and RSS-210. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operation is subject to the following two conditions;

(1) this device may not cause interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation of the device. Note:

Above sheet is the English translated version. In general, we use the Japanese one. As the above sheet is a draft version, some changes may be made. However, content of information will not be changed. 3. Outline of operation and Service manual Our product is one of vehicle parts incorporated into the vehicle as the original equipment. Therefore, we will not supply the users manual and service manual of the product. We describe the operation and service method as follows.

- Operation Our product will be placed in the stand-by state ready for radio frequency radiation when the ignition is ON. Then, the product will radiate radio wave by stepping on the vehicles accelerator and changing vehicle into the motion.

- Service The axis of RF beam is adjusted according to the following steps. 1. For the adjustment of vertical RF beam axis vertical angle of RF beam is adjusted. 2. For the adjustment of Horizontal RF beam axis

- The screw for vertical adjustment of Millimeter wave radar sensor is turned by a wrench, and the

- The Ignition of vehicle is turned ON.

- The inspection equipment is connected to the vehicle.

- Gap of a horizontal axis is checked according to the work procedure displayed on the screen of

- Based on the inspection result, the right-and-left adjustment screw of Millimeter wave radar inspection equipment. sensor is adjusted by a wrench.

1-1, Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 November 16, 2012 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 Subject FCC ID Original grant date Applicant To Whom It May Concern:

This is to request a Class II permissive change for FCC ID: HYQDNMWR004, originally granted on 04/23/2012. We changed the following points from the original model. Eliminate not in motion mode in accordance with the amendments made to 15.253

: Request for Class II Permissive Change

: HYQDNMWR004

: 04/23/2012

: DENSO CORPORATION Before change The product has two modes:

- in motion

- not in motion After change The product has only one mode:

- in motion No change is made to hardware, and the output power of in motion mode remains same, which is less than amended new limit as shown below. Output Power Original test result of in motion mode New Limit Average: 30.05 dBm Peak: 38.71 dBm Average: 50dBm Peak: 55 dBm No additional test is required because this change does not affect the output power of in motion mode. Please refer to Theory of Operation for the detail of this change. Thank you for your attention to this matter. Sincerely yours, Kazuo Sakakibara General Manager DENSO CORPORATION

1-1, Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 Letter Of Agency Date: November 16, 2012 Applicant: DENSO CORPORATION FCC ID: HYQDNMWR004 UL CCS 47173 Benicia Street, Fremont, CA 94538 Reference:

To whom it may concern:

We, the undersigned, hereby authorize Yoshinobu Asai of Application Section, WiSE Japan, UL Verification Service, UL Japan, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Japan, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. The application for the subject equipment has not been submitted to another TCB for certification. Sincerely Yours, Kazuo Sakakibara General Manager DENSO CORPORATION

1-1, Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 Request for Confidentiality Date: November 21, 2012 UL CCS 47173 Benicia Street, Fremont, CA 94538 RE: Certification Application FCC ID: HYQDNMWR004 Please be advised that the following information is to be held confidential on behalf of DENSO CORPORATION, referring to the FCC rules 0.457 and 0.459:

Theory of Operation The application contains technical information which DENSO CORPORATION deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, Kazuo Sakakibara General Manager DENSO CORPORATION

1-1, Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 FCC ID: HYQDNMWR004 Date: April 19, 2012 UL CCS 47173 Benicia Street, Fremont, CA 94538 Reference: Applicant: DENSO CORPORATION To whom it may concern:

We, the undersigned, hereby authorize Yoshinobu Asai of Application Section, WiSE Japan, UL Verification Service, UL Japan, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Japan, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. The application for the subject equipment has not been submitted to another TCB for certification. Sincerely Yours, Kazuo Sakakibara General Manager Engineering Administration Division

1-1,Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 April 19, 2012 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 Subject : Request for Class II Permissive Change FCC ID : HYQDNMWR004 Original gant date : 12/20/2007 Applicant : Denso Corporation To Whom It May Concern:

This is to request a Class II permissive change for FCC ID: HYQDNMWR004, originally granted on 12/20/2007. We changed the following points from the original model. Only the software is changed to change the modulation interval. There is no hardware changes. Please refer to attached Theory of operation for details of these modifications. This time, we performed the testing and confirmed that this product still meets the minimum requirements of the applicable rules of FCC. Please refer to the test report submitted with this application. Thank you for your attention to this matter. Sincerely yours, Kazuo Sakakibara General Manager Engineering Administration Division

1-1, Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 UL CCS 47173 Benicia Street, Fremont, CA 94538 Subject: Request for Confidentiality FCC ID: HYQDNMWR004 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Kazuo Sakakibara General Manager Engineering Administration Division April 19, 2012

1-1,Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: HYQDNMWR004 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Kazuo Sakakibara, Senior Manager Regulatory Affairs and Certification Center Engineering Administration Dept. DENSO CORPORATION

47173 Benicia Street, Fremont CA 94538 Tel: 510-771-1000, Fax: 510-661-0888 Federal Communication Commissions 7435 Oakland Mills Road Columbia MD 21046 Subject:

Ref:

Request FCC to replace previous submitted user manual Applicant: Porta Phone Company Inc. FCC ID: HYQDNMWR004 TCB Assessment no.: AN07T7440 Grant date: 12/20/2007 To Whom It May Concern:

CCS-TCB issued the grant on Dec. 20, 2007, during the upload the process, CCS mistakenly upload previous version of test report and RF Exposure information. CCS-TCB is requesting FCC to delete the following files from database:

RF exposure infoRF Exposure Info12/20/2007pdf12/20/2007 12/20/2007pdf12/20/2007 Test report Test Report The correct test report and RF exposure information have been uploaded to FCC with description of updated test report and updated RF exposure Info. Best Regards Mike Kuo / V.P. Compliance Certification Services Dec. 21, 2007

DENSO Marking layout and location (DNMWR004

(62. 5 mm) MODEL: DNMWROOd Q coxccrryyyz0 OMI] 1D: XXXXYYZZ2Z FCC ID-HYQDNWHROO4 C S/N 0 RERREERE 1: 1551 4-DNWURO04 DENSO sapan 6020 Oo mm) Fig. Marking Layout Marking location Fig. Marking Location Note: Labeling Information

- Label material: PET-01

- Method of labeling: Sticking on the product

1-1,Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan Tel : +81-566-25-5947 Fax : +81-566-25-4548 Request for Confidentiality (Short Term) Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID: HYQDNMWR004 To Whom It May Concern:

Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-

term confidentiality request on the following attachments in 45 days:

External Photos Internal Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Kazuo Sakakibara, Senior Manager Regulatory Affairs and Certification Center Engineering Administration Dept. DENSO CORPORATION