FCC ID: BABFT0108A Car Audio

User's Manual FT0108A Car Audio Audio con monitor La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Fujitsu Ten Confidencial The screen design may be changed. El diseo de la pantalla se cambio. Connect Bluetooth phone (Pairing) Una el telfono del Bluetooth (Dispositivo) 1.Press the button 1.empuje el botn de 2.Touch "+". 2.Toque "+". 3.Press Add Device and then select Bluetooth empuje "conector telefono" y luego selecciona 4.Busque su telfono celular en la pantalla. selecciona el bluetooth 4.Search the name on the display from your cell phone. 5. Select Pair both radio and your cellphone 5.Seleccione dispositivo su telfono celular 6. Select Set as favorite or skip 6. Seleccione favorito o cancelar 7.Completed connection 7.Conexin completada Fujitsu Ten Confidencial Make a call Haga una llamada 1.Press the button 1.empuje el botn de 2.Press phone number want to call and button 2.empuje nmero de telfono quieren llamar y empuje Receive a call Reciba una llamada 1.Press "Answer". 1.empuje "Respuesta". 2.Show up following display while receiving call 2.ve la pantalla siguiente recibiendo la llamada Fujitsu Ten Confidencial Connect Wifi Wi-Fi de conexin 1.Press the Settings Button 1.empuje botn de configuracion 2.Press Wi-Fi Networks. 2.empuje redes del Wi-Fi. 3.Press mark 3.empuje seal 4.Change Wi-Fi Services status to ON and search Wifi equ Type Wi-Fi Password and then completed connection. 4.encienda el estado de Wi-Fi Services entonces busque el equipo de Wi-Fi contrasea del Wi-Fi de la entrada y conexin completada Fujitsu Ten Confidential FCC ID : BABFT0108A FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: +/-4 ppm This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. IC : 2024B-FT0108A High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. La transmission des donnes est toujours initie par le logiciel, puis les donnes sont transmises par l'intermdiaire du MAC, par la bande de base numrique et analogique et, enfin, la puce RF. Plusieurs paquets spciaux sont initis par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numrique active l'metteur RF, puis dsactive celui-ci la fin du paquet. En consquence, l'metteur reste uniquement activ lors de la transmission d'un des paquets susmentionns. En d'autres termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information transmettre ou de dfaillance. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Fujitsu Ten Confidential

User's Manual FT0108A Car Audio Audio con monitor La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada.

Fujitsu Ten Confidencial The screen design may be changed. El diseo de la pantalla se cambio. Connect Bluetooth phone (Pairing) Una el telfono del Bluetooth (Dispositivo) 1.Press the button 1.empuje el botn de 2.Touch "+". 2.Toque "+". 3.Press Add Device and then select Bluetooth empuje "conector telefono" y luego selecciona 4.Busque su telfono celular en la pantalla. selecciona el bluetooth 4.Search the name on the display from your cell phone. 5. Select Pair both radio and your cellphone 5.Seleccione dispositivo su telfono celular 6. Select Set as favorite or skip 6. Seleccione favorito o cancelar 7.Completed connection 7.Conexin completada

Fujitsu Ten Confidencial Make a call Haga una llamada 1.Press the button 1.empuje el botn de 2.Press phone number want to call and button 2.empuje nmero de telfono quieren llamar y empuje Receive a call Reciba una llamada 1.Press "Answer". 1.empuje "Respuesta". 2.Show up following display while receiving call 2.ve la pantalla siguiente recibiendo la llamada

Fujitsu Ten Confidencial Connect Wifi Wi-Fi de conexin 1.Press the Settings Button 1.empuje botn de configuracion 2.Press Wi-Fi Networks. 2.empuje redes del Wi-Fi. 3.Press mark 3.empuje seal 4.Change Wi-Fi Services status to ON and search Wifi equ Type Wi-Fi Password and then completed connection. 4.encienda el estado de Wi-Fi Services entonces busque el equipo de Wi-Fi contrasea del Wi-Fi de la entrada y conexin completada

Fujitsu Ten Confidential FCC ID : BABFT0108A FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: +/-4 ppm This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. IC : 2024B-FT0108A High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. La transmission des donnes est toujours initie par le logiciel, puis les donnes sont transmises par l'intermdiaire du MAC, par la bande de base numrique et analogique et, enfin, la puce RF. Plusieurs paquets spciaux sont initis par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numrique active l'metteur RF, puis dsactive celui-ci la fin du paquet. En consquence, l'metteur reste uniquement activ lors de la transmission d'un des paquets susmentionns. En d'autres termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information transmettre ou de dfaillance.

Fujitsu Ten Confidential

Internal Photo Internal Photo Internal Photo Internal Photo

Internal Photo Internal Photo Internal Photo

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Letter of Authorization Date: May 19, 2021 UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant: DENSO TEN Limited FCC ID: BABFT0108A To whom it may concern:

We, the undersigned, hereby authorize Akiyo Hayashi of Consumer Technology Division, UL Japan, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Japan, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. The application for the subject equipment has not been submitted to another TCB for certification. Sincerely Yours, Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Request for Class II Permissive Change May 19, 2021 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, Maryland 21046 FCC ID : BABFT0108A Applicant : DENSO TEN Limited To Whom It May Concern:

This is to request a Class II permissive change for FCC ID: BABFT0108A, originally granted on 09/05/2019. We changed the following points from the original model. Change of Ethernet IC on Main PCB Please refer to attached Test Report and Theory of Operation-Details of changes for details of these modifications. Meanwhile we submit the following documents related to this change. There is no change before and after change except for these documents. Test Report RF Exposure External Photo Internal Photo User Manual Label Drawing/ Location Block Diagram Specification Schematic Diagram Parts List This time, we performed the testing and confirmed that this product still meets the minimum requirements of the applicable rules of FCC. Please refer to the test report submitted with this application. Thank you for your attention to this matter. Sincerely, DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

DENSO TEN Limited 2-28, Gosho-dori 1-chome, Hyogo-ku, Kobe, 652-8510 Japan Tel.: +81.78-682-2159 Fax.: +81.78-682-2169 Request for Confidentiality Date: May 19, 2021 UL Verification Services Inc. 47173 Benicia Street, Fremont, CA 94538 Applicant : DENSO TEN Limited FCC ID : BABFT0108A To whom it may concern:

Please be advised that the following information is to be held confidential on behalf of us, referring to the FCC rules 0.457 and 0.459:

Block Diagram Theory of Operation Schematics Parts List The application contains technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, Kaoru Abe Department General Manager Quality Assurance Group Quality Control Div Regulatory Management Dept. DENSO TEN Limited

FT0108A_External_Photos FT0108A_External_Photos FT0108A_External_Photos FT0108A_External_Photos RearRearRearRear LeftLeftLeftLeft Solder side Solder side Solder side Solder side Bottom Bottom Bottom Bottom FPFPFPFPFront Front Front Front RightRightRightRight Component side Component side Component side Component side TopTopTopTop Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential

FT0108A_FP_RF_Module&Antenna_Location Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential FT0108A_Photos_RF_Module Outside View (TOP) Outside View (BOTTOM) Inside View Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential Fujitsu Ten Confidential