FCC ID: 2BBQL-DH100 Devicebook Hub

Devicebook App User Manual Introduction to Devicebook App Devicebook App is the Smart Home App to set up and operate Devicebook Smart Home system. With the Devicebook app, contractor users can set up and test the Devicebook Smart Home system for their clients. Homeowners can use the Devicebook app to control and monitor their smart home, set up Alexa voice, add emergency responders, and more. Download Devicebook App Devicebook App is available for Android and iOS platforms. You can download it from the Google Play Store or Apple App Store. Note: Only devices with Android version 10 or above are supported. House Check After signing in, click on the Smart Home you want to set up. The first step to setting up the Smart Home is to use Devicebook House Check. House Check is the tool used to set up Devicebook Hub and the devices used in a smart home. Here are requirements to keep in mind:

Make sure the Devicebook Hub is powered on and connected to Internet using Ethernet Once you start House Check, do not interrupt it: If the Devicebook app is put in the background or if the phone goes to sleep House Check will be interrupted. Devices you have already set up will remain set up, but devices you were in middle of setting up will need to resume from start. At one time, only one user can run the House Check for a given smart home. If another user starts the House Check for the same smart home, the first user will get interrupted. To Start House Check scroll to the bottom of the main page and click on the House Check Widget as seen in the screenshot below:

Setting up the Devicebook Hub Before setting up the devices, the first step is to set up the Devicebook hub. 1. Click on "Set Up" button on the Devicebook Hub tile as shown in screenshot below. 2. Follow the instruction on the next page to set up the Hub and scan the QR code on the Hub. 3. Once the QR code is scanned, Devicebook will start setting up the Hub. Wait for the confirmation that the Hub was successfully set up as seen in screenshot below. Setting Up Devices Once the Devicebook Hub is set up and connected, it is time to set up the devices. In House Check, devices are grouped by the location (floor and room) based on the physical floor plan. To get the best signal strength for devices that interconnect via mesh network, it is recommended to set them up such that:

Set up devices on the same floor as the Devicebook Hub, starting from the closest room

(to the Hub) to the farthest away. Then, set up other floors. In each room, set up AC-powered (mains-powered) devices first. Then, set up the battery powered devices. To set up a device, first select the room where the device is located and then select the device to set up. 1. Press the "Set Up" button on the device you want to set up. 2. Devicebook will start to find matching devices on it's network. Follow the instructions shown on the page to perform any actions to find the candidate devices.

(Note: More than one devices may be found in this step. The next step will help you identify the specific device to set up) 3. Next step is to identify the specific device you are trying to set up. Follow the instructions to identify the device. For example, for a plug this may mean powering on and then powering off the plug. Devicebook will detect which device was powered on and off and automatically identify it. 4. Once the device is identified, Devicebook will proceed to set it up and you will see the success page Setting Up Insteon/Z-Wave devices If a smart home uses Insteon or Z-Wave devices, install repeaters as needed to make sure all devices have a good connection. Additional instructions for setting up Z-Wave devices:

1. Z-Wave devices require pairing with the Devicebook Hub. You will find the instructions to pair the Z-Wave device when Devicebook tries to find devices on the network. 2. If the device has been previously paired with a different Devicebook Hub or Z-Wave controller, you should first unpair the device using House Check and then continue pairing it by following the instructions on the screen. 3. Once a device has been identified, Devicebook will check it's signal strength to determine if this device can reliably connect to Devicebook Hub. The result of the signal strength will be shown once the check completes. The signal strength check can also be performed any time after the device has been set up, such as after all Z-Wave devices have been set up. Troubleshooting If you have trouble setting up the Devicebook Hub or find the devices, you will find the Troubleshooting Instructions in the Devicebook app in House Check. Click the Help or Troubleshoot button and follow the prompt to bring up the Troubleshooting Guide. Testing the Smart Home Once all devices have been set up in House Check, you can go to each installed solution to test the devices you have set up. For example, you can go to the Lighting Solution from the main page and test each switch/dimmer by powering it on/off individually or as a group. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Appendix ID Label Devicebook Hub FCC ID: 2BBQL-DH100 Model: DH100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Size for the label: 30mm X 30mm Appendix ID Label Location FCC ID: 2BBQL-DH100 TB-RF-074-1.0

Devicebook Inc. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 7/24/2023 Devicebook Inc. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought

(FCC ID: 2BBQL-DH100):

Name and company of U.S. agent: Devicebook Inc. Physical U.S. address of agent: 11811 NE 1st St, #A203, Bellevue, WA 98005 FRN of U.S. agent: 0033904160 Email address of U.S. agent: admin@devicebook.com Devicebook Inc. acknowledges their obligation to accept service of process on behalf of Devicebook Inc. Devicebook Inc.with the FRN [0033904160] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Signature Raymond Lo N/A Devicebook Inc. Signature Raymond Lo N/A Devicebook Inc. The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. 4 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4

Devicebook Inc. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 7/24/2023 To whom it may concern:

We, Devicebook Inc. hereby certify that the equipment for which authorization is sought (FCC ID:

2BBQL-DH100) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Sincerely, 2 0 V

, U

) i i

d n a

) i

) 5

) d

1 1 9

. 2 _ u q E d e r e v o C

l e d o m

_ 2 6 Signature Raymond Lo N/A Devicebook Inc. The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.