Issue departmentR&D Division Product Function instruction CB.34.33.01 Date Author 2019-11-17 Jarek NoCB3433A Version 1.0 Page 1 of 5 CB3433A Function instruction 1.Electrical configuration diagram 1 Issue departmentR&D Division Product Function instruction CB.34.33.01 Date Author 2019-11-17 Jarek NoCB3433A Version 1.0 Page 2 of 5 2.Function Picture 3.Interface function description3.1.HEAD ACTUATOR Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released Click head down buttonhead actuator moves in, stop when released This function takes effect only by pressing the corresponding button on the remote. 3.2.FOOT ACTUATOR Connect to foot actuator,control by remote single:
Click foot up buttonfoot actuator moves outstop when released Click foot down buttonfoot actuator moves instop when released This function takes effect only by pressing the corresponding button on the remote. 2 Issue departmentR&D Division Product Function instruction CB.34.33.01 Date Author 2019-11-17 Jarek NoCB3433A Version 1.0 Page 3 of 5 3.3.LUMBAR ACTUATOR Connect to foot actuator,control by remote single:
Click Lumber up buttonfoot actuator moves outstop when released Click Lumber down buttonfoot actuator moves instop when released This function takes effect only by pressing the corresponding button on the remote. 3.4.HEAD1 VIBRATION & HEAD2 VIBRATION Connect to head massage,control by remote:
Click head massage + button,head massage strengthens by one level;
Click head massage - button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote. 3.5.FOOT VIBRATION Connect to Foot massage,control by remote:
Click FOOT massage + button,head massage strengthens by one level;
Click FOOT massage - button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote. 3.6.Power LED & PAIRING LED Power supply for control box, PAIRING LED of control box is blue, POWER LED is green 3.7.PAIR & RESET button Function Pair Function Power supply for control box,Pair LED lights to bluethe control box enters into mode of code paring Press and hold the paring button of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the remote enters into mode of code paring;
The backlight of paring LED of remote stops flashing, and the paring led of control box turns off, it indicates that the code paring is successful;
3 Issue departmentR&D Division Product Function instruction CB.34.33.01 Date Author 2019-11-17 Jarek NoCB3433A Version 1.0 Page 4 of 5 Click button of underbed light, turns on(or change) the underbed light, switch the status once when click once This function takes effect only by pressing the corresponding button on the remote. If fails, repeat all the processes above;
3.8.SYNC port Connect with the same other Control box or Other accessories;
3.9.underbed light-RGB 3.10.USB Power OUT Connect USB panel 3.11.UART1 port & UART2 port Connect other serial peripherals 3.12.Power Connect to the 29V DC;
FCC Warning operation. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired 4 Issue departmentR&D Division Product Function instruction CB.34.33.01 Date Author 2019-11-17 Jarek NoCB3433A Version 1.0 Page 5 of 5 ISED RSS Warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and device.
(2) this device must accept any interference, including interference that may cause undesired operation of the Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 5