FCC ID: QNFT70-USA-RX T70-USA RX

etn conning re Eee Operating Instructions Press the OFF button to call up the next operating time. om, e Cc g oO

oe Ie

| be 7 : 4 Te | esta rt TF 0 Webasto Thermosysteme GmbH

| - do not oianneat for 10 seconds, or Postfach 80 - D-82132 Stockdorf - Hotline (01805) 93 22 78

| - actuate the button. Hotfax (0395) 55 92-353 - http://www.webasto.de Returning to the Default Setting Press the ON and OFF buttons simultaneously for approx. 10 seconds until the LED extinguishes. Default setting: heating mode, 30 minutes. General A : The wireless Webasto Telestart T70 enables Webasto heating units a - Thermo Top, Thermo Top T, Thermo Top Z/C and Thermo Top E -

Press the ON or OFF button. or the vehicle fan to be switched on and off from a distance of up to 600 m. pas To switch on the vehicle fan for ventilating the vehicle interior requires a mode change on the transmitter to be carried out. The receiver limits the operating time once the heater has been switched on by the transmitter. The maximum range can be achieved in open country. In built-in areas the range is likely to be reduced. 5 Batteries | LED ~ Action NOTE:

oka sare can ! A minimum distance of 2 m must be maintained between the Telestart y lights up aan hand-held transmitter and the antenna in the vehicle in the following cases:

4 we oom i tae | jcvinty em iene S|: hs - teaching the codes of the Telestart hand-held transmitter low charge after 1 sec. flashes - Warm up batteries to above 0C 3 g wuntiine ce a. tm - n f - i S 5 :

eee conan ee & Or else, cover the antenna at the hand-held transmitter with your hand a during the transmitting operation. discharged after 1 sec. - Warm up batteries to above 0C Ea |

lights up for - Replace batteries s |

5 sec, in oranae s |

tT FCC ID: QNFT70-USA-RX |

CAUTION FCC ID: ONFT70-USA-TX a |

This device complies with part 15 of the FCCrules. is

: cee Operation is subject to the following two conditions: |

Changes or modifications to this unit not expressly (1) This nantes harmful interferences, =|

approved by the party responsible for compliance could and (2) this device must accept any interference +

void the user's authority to operate the equipment, received, including interference that may cause 5 |

Bg J undesired operation.

rogramming Telestart Transmitters

| 1. Place batteries into the battery compartment of the transmitter.

| 2. Remove fuse 1A (black) from the heater's fuse holder (voltage interruption). 3. Wait at least 5 seconds. 4. Replace fuse in heater's fuse holder and within 5 seconds press the OFF button on the transmitter for at least 1 second. 5. "Learning" is completed. _Asecond or third hand-held transmitter can be programmed in the same manner. OFF min. 1 sec. max. 5 sec. Checking the Mode Simultaneously depress and hold down the ON and OFF buttons. LED illuminates:

in red: heating mode in green: ventilating mode LED extinguishes:

_- when the buttons are released, or _- after 10 seconds Mode setting Depress the ON and OFF buttons simultaneously twice within one second. Upon the second actuation, the LED will change its colour and illuminate until the buttons are released. The new mode is stored when the button is released. jold the hand-held transmitter with the antenna in upright position and push the ON button for 1 to 2 seconds.

| ! NOTE:

| In the 'heating' mode, the vehicle's heating system is to

| be set to "warm" prior to leaving the vehicle.

| In the 'heating' and ventilation modes, the vehicle's fan switch is to be turned to position 1 in the case of 3-

speed blower fans, and to position 2 in the case of 4-

speed blowers. In the case of infinitely variable fans adjust to at least 1/3 of the fan's capacity. Switch on heater or ventilation H |

Switch off heater or ventilation Hold the hand-held transmitter with the antenna in upright position and press the OFF button for 1 to 2 seconds. Checking and Setting the Operating Time The operating time of the heater or the vehicle's fan can be preset on the transmitter in increments of 10 minutes. The operating time is factory-set at 30 minutes. NOTE:

In the case of Thermo Top and Thermo Top T heaters, an operating time of 20 or 30 minutes has to be set in the heating mode. In the case of Thermo Top Z/C and Thermo Top E heating units we recommend that the heating time be set in accordance with the driving time. Example: The vehicle is used for travelling to work and back. With a driving time of approx. 30 minutes (one way), we recommend setting an operating time of 30 minutes. Checking the Operating Time Simultaneously actuate the ON and OFF buttons within one second three times in rapid succession.

' NOTE:

The first coded flashing signal that is emitted immediately upon the third actuation of both buttons has to be included into the count. The LED flashes in accordance with the preset operating time.

| No. of coded flashing signals 1 2 3. 4 5 6 |

Operating time 10min. 20min. 30min. 40min. 50min. 60 min. |