SERVICE MANUAL IFT-2220 INFOTAG 1.44 IFT-2220 COPYRIGHT 2010 TERAOKA WEIGH-SYSTEM PTE LTD Table of Content i) ii) iii) Notice ................................................................................................................................................. 1 Safety Information .............................................................................................................................. 2 Safety Regulations ............................................................................................................................. 2 1. General ............................................................................................................................................................. 5 1.1 Model Specification ............................................................................................................................ 5 1.2 Operating Specification ...................................................................................................................... 5 2. Dimension ........................................................................................................................................................ 6 3. IFT-2220 Setup Diagram & Spec Setting ...................................................................................................... 7 3.1 Overall Layout and Label design ......................................................................................................... 7 3.2 Exploded View ....................................................................................................................................... 8 3.3 Replacement of Info Tag Battery ........................................................................................................ 10 3.4 Button Cell Specifications .................................................................................................................... 10 3.5 ESL Attachment (Refer to ESL Attachment Catalogue) ..................................................................... 10 3.6 Product Handling of Info Tag ............................................................................................................... 10 4. Revision Records .......................................................................................................................................... 11 i) Notice DIGI The material contained in this document is proprietary and for information only and is subject to change without notice. Teraoka Weigh-System assumes no responsibility for any errors or damages arising from misinterpretation of any procedure. Screen displays, operating procedures and supporting features might vary with different software version releases. This document shall not be reproduced whether in part or whole without the written consent from Teraoka Weigh-System Pte Ltd. Teraoka Weigh-System Pte Ltd 4, Leng Kee Road
#06-01 SIS Building Singapore 159088 1 ii) Safety Information The operator of the equipment shall comply with the safety and warning indications and procedures outlined in this document. Teraoka Weigh-System Pte Ltd assumes no responsibility or liability for failure to comply with these requirements. Repair and servicing of product, shall only be carried out by trained and qualified personnel. Disclaimer:
Specifications are subject to change without notice. All dimensions shown are approximate. Please be aware that Teraoka has indicated that its hardware and software used in the product may require additional updates in the future as our product is continually under development. The need for such updates most likely applies to the Printer software. CAUTIONS:
FOR PLUGGABLE EQUIPMENT, THAT THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. POUR LE MAT RIEL RACCORD PAR PRISE DE COURANT, LE SOCLE DE PRISE DE COURANT DOIT TRE INSALL PROXIMIT DU MAT RIEL ET DOIT TRE AIS MENT ACCESSIBLE. FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE. POUR NE PAS COMPROMETTRE LA PROTECTION CONTRE LES RISQUES DINCENDIE, REMPLACER PAR UN FUSIBLE DE M ME TYPE ET DE M ME CARACT RISTIQUES NOMINALES. DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURERS INSTRUCTIONS IL Y A DANGER DEXPLOSION SIL Y A REMPLACEMENT INCORRECT DE LA BATTERIE. REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU MME TYPE OU DUN TYPE RECOMMAND PAR LE CONSTRUCTEUR. METTRE AU R BUT LES BATTERIES USAG ES CONFORM MENT AUX INSTRUCTIONS DU FABRICANT. iii) Safety Regulations Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 2
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IDA Compliance Statement: (Singapore) This equipment registered to comply with IDA (Info-Communications Development Authority of Singapore) Standard under Dealers Class License. Actual size 9mm (H) x 17mm (W) Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage prjudiciable, et
(2) (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. 3 For Taiwan 4 1. General 1.1 Model Specification Model Dimensions (in mm) Weight Power Source Operating Temperature Humidity IP Rating Battery Specification 1.2 Operating Specification Power Source Operating Temperature Humidity IFT-2220 Service Manual IFT-2220 (INFOTAG 1.44) Infotag
LCD Size Display Window LCD Resolution
: 26g approx. (Info Tag)
: DC Cell Button Battery 3.0V
: 0 C to +40 C
- 46.2 (L) X 39.0 (H) X 11.4 (W)
- 40.5mm x 28.8mm
- 30.3mm x 23.0mm
- 128 x 96 dots
: 85% Max. Non-condensing
: NA
: Type Nominal Voltage Weight Life Time
- CR2450 (Cell Button Battery)
- 3.0V
- 5 years (1 update/day)
- 6.6g approx.
: CR2450 (Cell Button Battery)
: NA Internal
: External
: 0C to +40C
: 85% Max. Non-condensing 5 IFT-2220 Service Manual 2. Dimension Info Tag (IFT-2220) 6 3. IFT-2220 Setup Diagram & Spec Setting 3.1 Overall Layout and Label design Infotag (IFT-2220) IFT-2220 Service Manual Front View Back View 7 IFT-2220 Service Manual 3.2 Exploded View Info Tag (IFT-2220) 8 IFT-2220 Service Manual Note:
This product is fully sealed by Ultrasonic Welding process.
(Above the information is only reference for factory and Technical department.) 9 3.3 Replacement of Info Tag Battery IFT-2220 Service Manual Location of Battery in Info Tag Battery Cover Battery Info Tag Pull off the battery cover from back of the Info Tag. i. ii. Replace the new battery. (Ensure the Battery polarity is correct) Caution: Dispose of the Battery according the Safety Guideline. Avoid placing the battery in reverse polarity. ii. Do not heat or dispose of fire. May burst or release toxic material. iii. Do not charge. iv. Do not short circuit. v. Do not solder the battery directly. i.
3.4 Button Cell Specifications 3.5 ESL Attachment (Refer to ESL Attachment Catalogue) For all information about the ESL Various Attachment type, function, installation etc. Please refer to ESL Attachment Catalogue 3.6 Product Handling of Info Tag Handle product with care. Do not expose product to corrosive chemical solution, any organic solvent acidic or alkaline. If cleaning is required, wash only water or mild soap solution. Do not attempt to disassemble, apply force or heavy load to the product. No user serviceable parts inside. 10 IFT-2220 Service Manual Software Version Remarks V0.01 Tentative Edition 4. Revision Records Serial No. 001 002 003 Date JAN 13 MAR 13 APR 13 Edition Status 00 01 02 Description of Changes First Release ADD IC STATEMENT UPDATE FCC STATEMENT AND LABEL 11