1115 WIRELESS TEMPERATURE SENSOR AND FLOOD DETECTOR Installation Guide 1 PROGRAM THE PANEL The 1115 Wireless Temperature Sensor and Flood Detector can be programmed with up to four zones. When programming the 1115 in the panel, refer to the panel programming guide as needed. Note: When a wireless receiver is installed, powered down and powered up, the panel is reset, or programming is complete, the supervision time is reset. If the receiver has been powered down for more than one hour, the 1115 may take up to an additional hour to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life. A missing message may display on the keypad until the supervision message is sent. 1. In ZONE INFORMATION, enter the ZONE number and press CMD. Note: Zones must be entered sequentially. For example, if you begin by programming zone 80, you would need to program zone 81 as the next contact. 2. Enter the ZONE NAME and press CMD. 3. Select SV (Supervisory) as the Zone Type and press CMD. 4. At the NEXT ZONE prompt, select NO. If you see the WIRELESS ZONE prompt, select YES. 5. Enter the eightdigit SERIAL NUMBER and press CMD. 6. Enter the CONTACT number being used. Note: Contacts can be entered in any order. Refer to Table 1 to select the correct contact. 7. Enter the SUPRVSN TIME and press CMD. 8. At the NEXT ZONE prompt, select YES and continue to program up to three more zones. 2 INSTALL THE BATTERIES After the transmitter has been programmed into the panel, install the batteries. Use only 3.0V lithium batteries, DMP Model CR123A, or the equivalent battery from a local retail outlet. Keep in mind, when setting up a wireless system, program zones and connect the receiver before installing batteries in the transmitters. 1. Remove the cover by pushing the button on the end of the cover and gently pulling upwards. 2. Observing polarity, place the battery in the holder and press into place. LT-1547 2016 Digital Monitoring Products, Inc. 16462 Figure 1: 1115 Wireless Temperature Sensor and Flood Detector DESCRIPTION The 1115 Wireless Temperature Sensor and Flood Detector is designed to be used in a variety of applications. The 1115 has an internal temperature sensor that can be set to detect cold, hot, or warm temperature ranges. When combined with the remote T280R temperature probe, the 1115 can be set to monitor refrigerated or freezing temperatures. The 1115 can also be paired with the remote 470PB water sensor and used in situations where flood detection is necessary. Depending on a customers needs, the 1115 can be programmed with up to four zones and serve as a temperature sensor, flood detector, or both. Compatibility All DMP 1100 Series Wireless Receivers and burglary panels. See the last page for compatibility details. What is Included?
One 1115 PCB mounted in a twopart housing One 3V lithium CR123A battery One 2M EOL resistor Mounting screws PRELIMINARY 3 SELECT A LOCATION The 1115 provides a survey capability to allow one person to confirm communication with the wireless receiver or panel while the cover is removed. This allows you to easily determine the best location for the 1115. Be sure to choose a location on a flat wall or singlegang box away from large metal objects. Tamper Switch Survey LED T C F 1. Hold the 1115 in the exact desired location. 2. Press the tamper switch to send data to the receiver and determine if communication is confirmed or faulty. See Figure 2 for tamper switch and LED locations. Confirmed: If communication is confirmed, the survey LED turns on when data is sent to the receiver and off when acknowledgement is received. Faulty: If communication is faulty, the LED remains on for about 8 seconds or flashes multiple times in quick succession. 3. Relocate the 1115 or receiver until the LED confirms clear communication. Proper communication between the 1115 and receiver is verified when for each press or release of the tamper switch, the LED blinks immediately on and immediately off. Figure 2: Tamper Switch and Survey LED 4 SET THE DIP SWITCHES The 1115 has four DIP switches (labeled 1 through 4) located on the PCB. Cold and flood settings can be turned on or off. Hot/warm and freeze/refrigerate are eitheror settings. Refer to Table 1 for DIP switch setting options and operations:
OPERATION DIP SWITCH POSITION CONTACT ALARM OCCURS WHEN:
ZONE RESTORES WHEN:
SENSOR Cold Hot 1 = ON 2 = OFF Warm 2 = ON Freezer 3 = OFF Refrigerator 3 = ON Flood 4 = ON 1 2 2 3 3 4 Temperature drops below 45F for
>10 minutes Temperature rises above 48F for > 4 minutes Temperature rises above 95F for
> 10 minutes Temperature drops below 92F for > 4 minutes Temperature rises above 75F for
> 10 minutes Temperature drops below 72F for > 4 minutes Internal Internal Internal Temperature rises above 10F for
> 30 minutes Temperature drops below 7F for > 4 minutes External (T280R) Temperature rises above 42F for
> 30 minutes Temperature drops below 39F for > 4 minutes External (T280R) Probe tips are in contact with water for > 3 minutes Probe tips have not been in water for > 3 minutes External (470PB) Table 1: DIP Switch Settings and Operation 1115 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 2 PRELIMINARY WIRE THE SENSOR PROBES (Optional) 5 If freezer or refrigerator sensing functionality is required, connect a T280R temperature sensor probe. If flood sensing functionality is required, connect a 470PB water sensor probe. When connecting a remote probe to the terminal block, DMP recommends using 18 or 22gauge unshielded wire. Do not use twisted pair or shielded wire. Connect the 470PB Water Sensor Probe To use the 470PB, place the probe inside the area and run 18 or 22gauge unshielded wire to the 1115. Follow these steps to connect the wire to the 1115 terminals:
1. Connect a wire from the top of one of the sensors probes to the F terminal on the 1115 PCB by running it through the wiring opening in the housing. See Figures 3 and 5. 2. Connect a wire from the top of the other probe to the C terminal on the 1115 PCB by running it through the wire opening in the housing. 3. Connect a 2M EOL resistor (included with the 1115) between the two probes. Connect the T280R Temperature Sensor Probe To use the T280R, place the probe inside the refrigerator or freezer environment and run 18 or 22gauge unshielded wire to the 1115. Follow these steps to connect the wire to the 1115 terminals:
1. Connect the grey wire to the T terminal on the 1115 PCB by running it through the wire opening in the housing. See Figures 4 and 5. 2. Connect the black wire to the C terminal on the 1115 PCB by running it through the wire opening in the housing. MOUNT THE 1115 6 It is recommended the sensor be mounted on a flat wall away from large metal objects. Do not mount the 1115 inside of freezers or walkin refrigerators. In those situations, use the optional remote T280R temperature probe. Terminal Block SENSOR PROBES 2M EOL Resistor Connect to Terminal C Connect to Terminal F Figure 3: 470PB Water Sensor Probe Connect to Terminal C Connect to Terminal T Figure 4: T280R Temperature Sensor Probe Wire Opening Optional Mounting Hole T C F 1. Hold the transmitter base on the wall and place one screw into the mounting hole location shown in Figure 5 and secure the housing to the surface. Note: You can place an additional screw in the optional mounting hole if needed. 2. Snap the transmitter housing cover back on the base. Mounting Hole Figure 5: Mounting Holes and Terminal Block 1115 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3 PRELIMINARY REPLACE THE BATTERY 1. Remove the cover by pushing the button on the end of the cover and gently pulling upwards. 2. Remove the old battery and dispose of it properly. 3. Observing polarity, place the new battery in the holder and press into place. 4. Snap the transmitter housing cover back on the base. Caution: Properly dispose of used batteries. Do not recharge, disassemble, heat above 212F (100C), or incinerate. Risk of fire, explosion, and burns. Sensor Reset to Clear LOBAT When the battery needs to be replaced, a LOBAT message will display on the keypad. Once the battery is replaced, a sensor reset is required at the system keypad to clear the LOBAT message. 1. On a Thinline keypad, press and hold 2 for two seconds. On a touchscreen keypad press RESET. 2. Enter your user code if required. 3. The keypad displays SENSORS OFF followed by SENSORS ON. FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be located or operated in conjunction with any other antenna or transmitter. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada Information This device complies with Industry Canada Licenceexempt RSS standard(s). Operation is subject to the following two conditions:
1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This system has been evaluated for RF Exposure per RSS102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits. Lexposition aux radiofrquences de ce systme a t value selon la norme RSS-102 et est juge conforme aux limites tablies par le Code de scurit 6 de Sant Canada. Le systme doit tre install une distance minimale de 7.87 pouces (20 cm) sparant lantenne dune personne prsente en conformit avec les limites permises dexposition du grand public. Specifications Battery Life Expectancy Type Frequency Range Dimensions Color Housing Material Accessories 470PB T280R Replacements CR123A 3 Years (normal operation) 3.0V Lithium CR123A 905924 MHz 3.3 L x 1.6 W x 1.2 H White Flame retardant ABS Water Sensor Probe Temperature Sensor Probe 3.0V Lithium Battery Certifications FCC Part 15 Registration ID CCKPC0192 (pending) Industry Canada Registration ID 5251APC0192 (pending) Compatibility 1100X Wireless Receiver version 104 or higher 1100XH Wireless Receiver version 105 or higher 1100D Wireless Receiver version 104 or higher 1100DI Wireless Receiver Version 105 or higher 1100DH Wireless Receiver Version 105 or higher XT50 Series panels with integrated wireless receiver version 101 or higher XTL Series panels with integrated wireless receiver version 104 or higher XTLplus Series Panels Patents U. S. Patent No. 7,239,236 Designed, engineered, and manufactured in Springfield, Missouri I N T R U S I O N F I R E A C C E S S N E T W O R K S 2500 North Partnership Boulevard Springfield, Missouri 658038877 800-641-4282 | dmp.com PRELIMINARY