all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Installation manual | Users Manual | 232.96 KiB | May 01 2001 / May 02 2001 | |||
1 | Attestation Statements | May 01 2001 / May 02 2001 | ||||||
1 | Operational Description | May 01 2001 / May 02 2001 | ||||||
1 | Internal Photos | May 01 2001 / May 02 2001 | ||||||
1 | ID Label/Location Info | May 01 2001 / May 02 2001 | ||||||
1 | Parts List/Tune Up Info | May 01 2001 / May 02 2001 | ||||||
1 | Parts List/Tune Up Info | May 01 2001 / May 02 2001 | ||||||
1 | Attestation Statements | May 01 2001 / May 02 2001 | ||||||
1 | Test Report | May 01 2001 / May 02 2001 |
1 | Installation manual | Users Manual | 232.96 KiB | May 01 2001 / May 02 2001 |
W A R N I N G This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Installation Manual PC5132-433 Version 4.0 WARNING Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warn-
ing to the attention of the users of this system. System Failures This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be:
nnnnn Inadequate Installation A security system must be installed properly in order to provide ad-
equate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building mate-
rials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available. nnnnn Criminal Knowledge This system contains security features which were known to be effec-
tive at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected. nnnnn Access by Intruders Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insuf-
ficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system. nnnnn Power Failure Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper opera-
tion. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inop-
erative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power inter-
ruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended. nnnnn Failure of Replaceable Batteries This systems wireless transmitters have been designed to provide sev-
eral years of battery life under normal conditions. The expected bat-
tery life is a function of the device environment, usage and type. Am-
bient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device has a low battery monitor which iden-
tifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will keep the system in good operating condition. nnnnn Compromise of Radio Frequency
(Wireless) Devices Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jam-
ming or other inadvertent radio signal interference. nnnnn System Users A user may not be able to operate a panic or emergency switch possi-
bly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm. nnnnn Smoke Detectors Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flam-
mable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be cir-
cumstances when there is insufficient warning to allow all occu-
pants to escape in time to avoid injury or death. nnnnn Motion Detectors Motion detectors can only detect motion within the designated ar-
eas as shown in their respective installation instructions. They can-
not discriminate between intruders and intended occupants. Mo-
tion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation. Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radia-
tors, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on. nnnnn Warning Devices Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an interven-
ing wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or pass-
ing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person. nnnnn Telephone Lines If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect. nnnnn Insufficient Time There may be circumstances when the system will operate as in-
tended, yet the occupants will not be protected from the emer-
gency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings. nnnnn Component Failure Although every effort has been made to make this system as reli-
able as possible, the system may fail to function as intended due to the failure of a component. nnnnn Inadequate Testing Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational de-
vices that are part of the system. nnnnn Security and Insurance Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a sub-
stitute for property owners, renters, or other occupants to act pru-
dently to prevent or minimize the harmful effects of an emer-
gency situation. Table of Contents C O N T E N T S Introduction 1 1.1 How to use this Manual ........................................................................ 1 1.2 Specifications and Features ................................................................. 1 1.3 Compatible Wireless Devices ............................................................... 2 1.4 Batteries ................................................................................................ 2 3 PC5132 Set up & Wiring 2.1 Unpack the PC5132 ............................................................................. 3 2.2 Choose a Mounting Location for the PC5132 ...................................... 3 2.3 Antennas ............................................................................................... 3 2.4 Connect the PC5132 Receiver ............................................................. 3 Enrolling Wireless Devices 4 3.1 A Note about Electronic Serial Numbers .............................................. 4 3.2 Enrolling Wireless Devices ................................................................... 4 3.3 Enroll & Program Wireless Keys (WLS9X9-433) ................................... 4 Identified Wireless Keys ....................................................................... 6 3.4 Other Programming 7 4.1 Program Zones and Partitions .............................................................. 7 4.2 Enable PC5132 Supervision ................................................................. 7 4.3 Enable Supervision of Wireless Zones ................................................. 8 4.4 Jamming Signal Detection .................................................................... 8 4.5 PC5132 Software Default ...................................................................... 9 4.6 Deleting Wireless Devices .................................................................. 10 11 Testing & Mounting 5.1 Test the Reception of Wireless Devices ............................................. 11 5.2 Mount the PC5132 and Wireless Devices .......................................... 13 14 Additional Notes Trouble Conditions .............................................................................. 14 6.1 6.2 Jamming Signal Detection .................................................................. 14 6.3 Wireless Zone Low Battery Transmission ........................................... 14 Troubleshooting Programming Worksheets Guidelines for Locating Smoke Detectors Index 16 17 22 23 Thank you for purchasing the PC5132 Wireless Receiver. This product is the result of several years of development and will allow you to connect up to 32 wireless detection devices to the PC580, PC1555, and the Power series control panels. The PC5132 uses 433 MHz. It provides several advantages:
supervisory transmissions are sent every 64 minutes programmable supervisory window can be as long as 24 hours diversity antenna arrangement for better RF reception In addition, the PC5132 features:
6 digit serial numbers for all wireless devices: These new serial numbers include hexadecimal digits. Please read Section 3.1 A note on Electronic Serial Numbers (ESN) for more information on enrolling 6-digit devices. We are confident you will find the PC5132 Wireless Receiver a unique and useful control panel enhancement. Introduction E C T I O N 1 S This manual describes how to install, program and maintain the PC5132. Before you install the PC5132 module, you should complete the following steps in your system installation:
1. Plan the installation and wiring of the security system (see your system 2. 3. Installation Manual). Install the control panel, and install and enroll at least one keypad to use for programming. Install and enroll any hardwired zone expander modules (PC5108) you plan to use. NOTE: PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g., zones 9-12 and zones 13-16). None of the zones assigned to a PC5108 module can be used for wireless devices. Program the PC5132 from a system keypad or using downloading software on a remote computer (e.g. DLS-3). Read your system Installation Manual for more information. 1.1 How to use this Manual Read this manual before you begin installing the PC5132. To install and set up the PC5132 and wireless devices, follow these steps. Refer to the sections listed below. 1. Temporarily mount and wire the PC5132 module (see Section 2). 2. Enroll and program wireless devices (see Section 3). 3. Complete zone and other programming on the system (see Section 4). 4. Test the placement of all the wireless devices (see Section 5). 5. Permanently mount the PC5132 receiver and wireless devices (see Section 5). For additional information on trouble conditions, RF jamming signal detection and battery replacement, see Section 6. For help with troubleshooting, see Section 7. 1.2 Specifications and Features Current Draw: 80 mA Frequency: 433 MHz Zones - receiver can receive signals from up to 32 wireless zones and 16 wireless keys Antenna - diversity design for enhanced performance Supervisory - programmable supervisory window, 4 to 24 hours, in 15 minute increments Location
- can be wired up to 750 ft. / 230 m from the main panel with 22 gauge wire
- connects to Keybus
- for longer wire runs, thicker gauge wire must be used. Compatibility: The PC5132 v4.0 can be connected to the following panels:
PC501X, PC1555, PC580 1 I N T R O D U C T I O N 1.3 Compatible Wireless Devices Please refer to the Instruction sheets of the following devices for more information. The PC5132 v4.0 can receive signals from the following devices:
WLS904-433 Motion Detector WLS906-433 Smoke Detector WLS925L-433 Transmitter
*When available WLS912-433 Glass Break Detector*
WLS914-433 Pet-Immune PIR*
WLS909-433 Wireless Key 1.4 Batteries The wireless devices, with the exception of the WLS925L transmitter and the WLS909 wireless key, are designed to use only Energizer Alkaline batteries (by Eveready). NOTE: Do not use other brands of batteries. Using any other brand may affect system operation. 2 PC5132 Set up & Wiring S E C T I O N 2 Diversity antennae Hardware for mounting the cabinet This section describes how to set up and wire the PC5132 module. 2.1 Unpack the PC5132 Check that the following parts are in your PC5132 package:
PC5132 PCB PC5132 plastic cabinet 2.2 Choose a Mounting Location for the PC5132 NOTE: Mount the PC5132 receiver and wireless devices after you have done placement tests with the wireless devices (see sections 5.1 and 5.2). Find a place that is:
Dry Central to the proposed placement of all wireless devices As high as possible Far from sources of interference, including: electrical noise (computers, televisions and electric motors in appliances and heating and air conditioning units); large metal objects like heating ducts and plumbing which may shield the antenna. Make sure that electrical wires will not run over the antenna(s) of the module when it is mounted. When mounting the PC5132 in a basement, place the module as high and as close to the underside of the first floor as possible. The range of the module will be reduced if the unit is mounted below ground level. 2.3 Installing the Antennas The two antennas must be screwed into the terminals marked ANT1 and ANT2, not GND1 and GND2. Also they must be installed as indicated in the following two diagrams:
Do not install the antennas as indicated in the following diagrams:
If the antennas are installed incorrectly the PC5132-433 may not reliably receive signals from the transmitters. 2.4 Connect the PC5132 Receiver CAUTION: Remove all power from the system while connecting modules to the Keybus. Connect the PC5132 to the four-wire Keybus of the control panel according to the following diagram. After you have completed the wiring, reconnect the power to the security system. Now that you have wired the PC5132, you should enroll and program the wireless devices. See section 3 for instructions. 3 Enrolling Wireless Devices S E C T I O N 3 This section describes how to enroll wireless devices (WLS904-433, WLS906-
433 and WLS925-433), and wireless keys (WLS909-433). For more information on these devices, read the instruction sheet included with each device. 3.1 A Note about Electronic Serial Numbers An electronic serial number (ESN) is printed on the back of each wireless device. ESNs are used to enroll the wireless devices with the PC5132 receiver. In order to reduce the occurrence of wireless devices with the same serial number, 6-digit serial numbers are now printed on the back of each wireless device. The 6-digit serial numbers include hexadecimal digits. For instructions on programming hexadecimal numbers, see your system Installation Manual, section 4: How to Program. NOTE: 6-digit serial numbers are only supported on the following control panels:
PC501X, PC1555 and PC580 v2.0 and higher. The WLS904-433, WLS906-433 and WLS925-433 devices have both a 5-digit and a 6-digit serial number printed on them. When connecting the PC5132 to a PC5010 v1.x panel, enter 5-digit serial numbers only. When connecting the PC5132 to a PC5015 v2.x and higher, PC5010, PC1555, or PC580 panel enter the 6-digit serial number. 3.2 Enrolling Wireless Devices (WLS904-433, WLS906-433, WLS925-433) 1. At a system keypad, enter [Q ][8][Installers code] to go to the installers programming section. 2. Enter programming section [804]. 3. Enter the 2-digit number corresponding to the zone the device is to occupy ([01] to [32]). NOTE: Hardwired and wireless devices cannot be assigned to the same zone. PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g. zones 9-
12 and zones 13-16). None of the zones assigned to a PC5108 module may be used for wireless devices. For more information on zone assignment, consult your system Installation Manual. 4. Enter the devices ESN. Follow the instructions in section 3.1 above. 5. Record the serial number and the assigned zone number in the programming worksheets in the back of this manual. 6. Continue with steps 3 - 5 until you have enrolled all wireless devices. 7. To exit press [#]. The device is now enrolled on the system. NOTE: The devices will not work properly until you complete zone and partition programming (see section 4). 4 W I R E L E S S D E V I C E S 3.3 Enroll & Program Wireless Keys (WLS909-433) For wireless keys to work on the system, you need to enroll them and then program the function buttons. Wireless keys are not assigned to zones and require no zone programming. You can enroll up to 16 wireless keys on the system. Enroll Wireless keys 1. At a system keypad, enter [Q ][8][Installers code] to go to the Installers Programming section. 2. Enter programming section [804]. 3. Enter a 2-digit number [41]-[56] to assign the wireless key a slot. These numbers correspond to wireless key numbers 01-16. 4. Enter the keys ESN. The entry must be six digits. If an older key with a 5-digit ESN is being enrolled, add the digit [0] to the beginning of the ESN. (E.g. ESN=61234, enter 061234) 5. The key is now enrolled on the system. Record the serial number and the assigned slot number in the programming worksheets in the back of this manual. 6. Repeat steps 3 - 5 until all wireless keys have been enrolled. 7.
(PC501XXXXX only)
(PC501
(PC501 only) only) only) By default, all wireless keys are assigned to Partition 1. only)
(PC501
(PC501 To assign keys to Partition 2, enable the appropriate options in programming sections [91] and [92]. NOTE: A wireless key can only be assigned to one partition. 8. To exit press [#]. Program the WLS909-433 Function Buttons WLS909-433 wireless keys have four programmable function buttons. You must program a set of four functions for the buttons before any keys will work. After the functions are programmed, when you press and hold one of the four buttons for two seconds, the system will execute the programmed function. For systems not using partitions: program the function buttons in section
[59]. All wireless keys will have the same four functions. For systems using 2 partitions (PC501X only): all wireless keys assigned to Partition 1 will have the four functions programmed in section [59]. All wireless keys assigned to Partition 2 will have the four functions programmed in section
[60]. For example, if function button 1 in Section [59] is programmed for Stay arming, then pressing the first button on wireless keys assigned to Partition 1 will Stay arm Partition 1. NOTE: Wireless keys will not work when the partition they are assigned to is being accessed for zone bypassing or programming. 1. At a system keypad, enter [Q ][8][Installers code]. 2. Enter programming section [804]. 3. Enter programming section [59] for keys assigned to partition 1, or [60]
for keys assigned to partition 2. 4. For each of the 4 function buttons, enter the 2-digit number of the function you want to select. See the programming worksheets in the back of this manual for a list of function key options. 5 W I R E L E S S D E V I C E S 5. Record your programming choices in the worksheets in the back of the manual. 6. To exit press [#]. 3.4 Identified Wireless Keys Reporting by the system of openings/closings by individual wireless keys and command output [Q ][7] activation by wireless key buttons may be supported on certain control panels. To do this, the system will reserve access codes 17 32 for wireless keys 01-16 respectively. You must program one access code for each wireless key (using [Q ][5] access code programming) for this feature to work correctly. NOTE: Program these access codes on the system after you have connected the PC5132 to the Keybus (see section 2.4). Refer to your system Installation Manual for information on access code programming. Opening/Closing By Wireless Key Reporting NOTE: The Identified Wireless Key Closing option is only available with the PC501X, PC1555, PC580 v2.0 and higher by turning section [015] option 4 off. To enable the reporting of openings and closings by identified wireless keys:
Make sure the control panel is v2.0 or higher Program a valid access code for each key Program a closing and opening reporting code for each keys access code Turn off the Quick Arm option in section [015] option [4] of the control panel programming To ensure that an unidentified wireless key cannot disarm the system, turn off section [017], option [1] (in the control panel programming). This option is available in control panels with software version 2.1 or higher. Command Output Activation NOTE: The Identified Wireless Key Command Output Activation feature is only available with the PC501X, PC1555 and PC580 v2.0 and higher. To enable command output activation by wireless keys, ensure that:
The control panel is v2.0 or higher Program a valid access code for each key Enable the PGM output attribute Requires Access Code for each PGM output programmed as [Q ][7][1-4] in sections [141] to [154]. Now that you have enrolled all the wireless devices, you will need to program the system to work properly with the devices. See section 4 for more information. 6 Other Programming S E C T I O N 4 4.1 Program Zones and Partitions Now that you have enrolled the wireless devices, you should complete all zone programming on the system. Although the exact programming required varies depending on which control panel the PC5132 is connected to, you should check that the following programming areas are completed correctly for each wireless zone:
Enable zones and/or assign zones to one or more partitions (programming sections [201]-[209]). Program the definition for each zone (programming sections [001]-[004]). Enable the wireless zone attribute for each wireless zone (PC580, PC1555, PC501X v2.0 and up only) (sections [101]-[132]). See your system Installation Manual, for more information on each of the above programming sections. 4.2 Enable PC5132 Supervision The control panel will supervise the PC5132 receiver via the Keybus after at least one device has been enrolled on the module (see section 3.2 Enrolling Wireless Devices). To activate module supervision, after you enroll the first device(s):
1. Exit and then re-enter installers programming 2. Enter programming section [902]. Wait approximately 1 minute. 3. To exit press [#]. The system will generate a General System Supervisory trouble if the module is removed from the Keybus. If you need to remove the PC5132 module from an existing system, you will have to disable supervision of the PC5132. NOTE: Deleting all devices from the PC5132 or defaulting the PC5132 will cause a PC5132 supervisory fault To disable PC5132 supervision:
1. Disconnect the PC5132 from the Keybus 2. Enter [Q ][8][Installer Code]
3. Enter [902]. The control panel will clear all supervision and re-scan the system for connected modules. The scan will take approximately one minute. 4. To exit press [#]. To review which modules the control panel is currently supervising:
1. Enter [Q ][8][Installers Code]
2. Enter [903] to display all modules. On LED keypads, light [17] will indicate that the PC5132 is present on the system. On LCD keypads, scroll until the module name appears on the display. 3. To exit press [#]. 7 O T H E R P R O G R A M M I N G If the PC5132 module does not show on the keypad, one of the following conditions may be present:
the module is not connected properly to the Keybus there is a problem with the Keybus wiring run the module does not have enough power no devices have been enrolled on the PC5132 4.3 Enable Supervision of Wireless Zones NOTE: (for PC5010 v1.x control panels only) In order for wireless zones to be supervised, you must enable Double End of Line (DEOL) supervision in the PC5010 control panel. For more information, refer to your Installation Manual. NOTE: (PC501X, PC1555, PC580 v2.0 and higher only) For wireless supervi-
sion to work, you must enable the wireless zone attribute on all wireless zones
(sections [101] to [132], option [8] ON). Wireless Supervisory Window Each wireless zone (WLS906-433,WLS904-433 or WLS925-433) will send a supervisory signal every 64 minutes. If the receiver does not receive a signal within the time programmed for the Wireless Supervisory Window, it will generate a supervisory fault. To program the wireless supervisory window:
1. Enter [Q ][8][Installer Code] to enter Installer Programming. 2. Enter [804] to enter the PC5132 Module Programming. 3. Enter section [81]. 4. Enter the time period for the supervisory window. The window is programmed in 15 minute increments. The default programming is 96
(x15minutes), which is equal to 24 hours. Valid entries are (08) - (96), equal to 4 - 24 hours. 5. To exit press [#]. Disable/Enable Zone Supervision All wireless zones have supervision enabled by default. To disable supervision for any zone, enter the following at any system keypad:
1. Enter [Q ][8][Installer Code] to enter Installer Programming. 2. Enter [804] to enter the PC5132 Module Programming. 3. Enter sections [82], [83], [84] and [85]. Enable or disable supervision for each wireless zone by turning each relevant option on or off. 4. To exit press [#]. 8 O T H E R P R O G R A M M I N G 4.4 RF Jam Detect Zone For RF jamming detection to work, you must select an unused zone to be used as the RF Jam Detect zone. When the receiver detects an attempt to jam the RF signal, the RF Jam Detect zone will be violated and the system will generate a tamper signal. When the jamming signal is gone, the RF Jam Detect zone closes and the system sends a tamper restore signal. To enable RF jamming detection:
1. Enter [Q ][8] [Installers Code]. 2. Enter programming section [804]. 3. Select an unused zone to be the RF Jam Detect zone. Enter the 2-digit number ([01] to [32]) of the RF Jam Detect zone on the keypad, then program the serial number as [200000]. 3. Enter section [93]. Enter the 2-digit number of the RF Jam Detect zone
([01] to [32]) in the programming section. 4. Disable supervision for the RF Jam detect zone by turning the relevant option off in section [82], [83], [84] or [85]. (See section 4.3 for more information.) 5. RF jamming detection is now enabled. To exit Installer programming, press [#]. 4.5 PC5132 Software Default Returning the PC5132 programming to factory default settings is a quick way to remove all the enrolled devices from the system and reset all the programming in section [804]. NOTE: Performing this procedure will not change any programming sections except [804]. Resetting the control panel to factory default settings will not re-
turn the PC5132 module to factory default settings. To restore the PC5132 programming to the factory default settings:
1. Enter [Q ][8] [Installers Code]. 2. Enter programming section [996]. 3. Enter the Installers Code, followed by [996] again. The software for the PC5132 will be restored to its factory default settings. 4. To continue programming the unit, exit installers programming by pressing [#] and then re-enter installers programming by entering [Q ][8]
[Installers Code]. For instructions on restoring the default programming of the control panel or any other connected module, see your system Installation Manual. 9 O T H E R P R O G R A M M I N G 4.6 Deleting Wireless Devices To remove a wireless device from the system, follow the guideline for enrolling a wireless device (see section 3.2). Program the ESN as [000000]. The wireless device for the zone will be removed. NOTE: You may need to remove power from the panel in order to clear troubles caused by deleted zones. Now that you have completed all PC5132 related programming, you can test and mount the receiver and devices. See section 5 for more information. 10 Testing & Mounting S E C T I O N 5 5.1 Test the Reception of Wireless Devices It is very important to test the proposed placement of each wireless device before it is mounted. Following these steps will test the signal strength between the PC5132 and the wireless devices. You can test all of the devices together (global placement testing) or test each device individually. To test all the devices together, see Testing All Wireless Devices Together below. To test wireless devices individually, see Testing Individual Devices. NOTE: After you have enrolled the wireless devices, you must exit and then re-enter Installers Programming at least once before you can perform a placement test. Testing All Wireless Devices Together:
1. Temporarily put the WLS904-433, WLS906-433 and WLS925-433 devices in the places you want to mount them. 2. At a system keypad, enter [Q ][8][Installer Code]. 3. Enable the Global Module Placement test by entering section [804]. Then enter sub-section [90] and turn on option [8]. 4. Press [#] twice. 5. Enter programming section [904], then enter [01]. 6. Activate one of the devices being tested until a result is displayed on the keypad or sounded by the keypad or bell:
WLS904-433: To perform a Placement Test on the WLS904-433, remove the detector from the back plate and then replace it. Once the detector is replaced on the back plate the LED on the detector will flash rapidly 5 times to indicate that it has sent a transmission. The panel will show and/or sound the result of the placement test on the keypad. To Carefully replace the Carefully replace the perform a 2nd and 3rd test, repeat this procedure. Carefully replace the Carefully replace the Carefully replace the backplate onto the detector, ensuring that TOP is facing upward, backplate onto the detector, ensuring that TOP is facing upward, backplate onto the detector, ensuring that TOP is facing upward, backplate onto the detector, ensuring that TOP is facing upward, backplate onto the detector, ensuring that TOP is facing upward, or you may damage the tamper switch. or you may damage the tamper switch. or you may damage the tamper switch. or you may damage the tamper switch. or you may damage the tamper switch. NOTE: When you remove the detector from the backplate (tamper the unit), the detector will also be put into Detector Walk Test mode. While in Walk Test mode the detector will activate the LED when motion is detected. The detector will also send a signal to the receiver 5 seconds after motion is detected, indicated by 5 rapid flashes by the LED. The LED will only work in this fashion for 10 motion detections after a tamper/restore. Note that the panel will ignore these transmission signals with respect to a placement test. The only way in which the panel will acknowledge a placement test is if the backplate has, each time, been removed and restored. WLS906-433:Remove the detector from its backplate, wait 5 seconds and re-attach it, or hold a magnet near the raised line on the outer rim, then remove it. WLS907-433/WLS925-433: Open the contact by moving the magnet away from the unit. The keypad will show/sound the test result. After the first test result has been generated (about 10 seconds) close the contact to generate another test result. If the unit is attached to a door or a window, open and close the door or window to activate the device. 11 T E S T I N G
M O U N T I N G WLS909-433: Press any function key at several different locations. Read the test results at the keypad:
Result Good Bad LED Keypad LCD Keypad Buzzer/Bell Light 1 On Steady Light 3 On Steady Good Bad 1 Beep/Squawk 3 Beeps/Squawks Activate the device until you get 3 good results in a row. You may mount the WLS devices where results were good. Devices indicating a bad result must be moved to another location. You may only have to move the device a few inches to correct a bad result. NOTE: Do not mount any device where a bad test result was indicated. 7. Go to the next device to be tested and activate it until the test result is displayed/sounded. NOTE: Wait until the placement test of one device is shown/sounded before beginning to test the next device. Continue to test the devices until both the PC5132 and the devices are in good locations. If several wireless devices produce bad test results, you may need to move the PC5132 to a better location. (See section 2.2 for tips on finding a location for the PC5132.) 8. To exit the placement test and return to installer programming, press [#] twice. Testing Individual WLS904-433, WLS906-433, WLS907-433 and WLS925-433 Devices:
1. Temporarily place the WLS904-433, WLS906-433 or WLS925-433 where you want to mount it. 2. At a system keypad, enter [Q ][8][Installer Code]. 3. Enter programming section [904]. 4 Enter the 2-digit zone number for the device to be tested. 5. Activate the device being tested until a result is displayed on the keypad or sounded by the keypad or bell. (Same as step 5 in the Global Placement Test section, previous page.) 6. To test another device, press [#] once, then repeat steps 4 - 5. Continue to test the devices until both the PC5132 and the devices are in good locations. If several wireless devices produce bad test results, you may need to move the PC5132 to a better location. (See section 2.2 for tips on finding a location for the PC5132.) 7. To exit the placement test and installer programming, press [#] twice. Testing Individual Wireless Keys:
You cannot use the individual device test described above to test WLS909-433 wireless keys. To ensure that the PC5132 receiver is receiving transmissions from these devices, use the function keys on the WLS909-433 at several different points in the installation. 12 T E S T I N G
M O U N T I N G 5.2 Mount the PC5132 and Wireless Devices When you have tested reception of the PC5132 with all the wireless devices (see section 5.1) and you have a good mounting location, mount the PC5132:
1. Pull the Keybus wires through the hole at the bottom of the cabinet. 2. Mount the cabinet securely to the wall. Mount the Devices If you have conducted the placement test described in section 5.1 and got 3 good results in a row for each device, you can mount the wireless devices. See the Installation Sheet for each device for mounting instructions. Now that your PC5132 and wireless devices are mounted and working properly, read section 6 for information on potential wireless trouble conditions, RF jamming signals, and battery replacement. 13 Additional Notes S E C T I O N 6 6.1 Trouble Conditions The control panel always watches for possible trouble conditions. If a trouble condition occurs, the keypad Trouble light will turn on and the keypad will beep. Press [Q ][2] to display the trouble conditions. The following trouble conditions apply to the PC5132 and/or any enrolled devices. General System Tamper - This trouble is generated when the PC5132 plastic cover is removed. General System Supervisory - This trouble will be generated if the panel loses communication with any module connected to the Keybus. The event buffer will log a detailed description of the event. Device Low Battery - This trouble is generated when a wireless device exhibits a low battery condition. Press [7] one, two, or three times to view which devices are experiencing battery failure. An LED keypad will indicate battery failure using zone lights 1 to 8. Zone Tamper - This trouble is generated when an enrolled wireless device is removed from its mounting location. Zone Fault - Each wireless zone will send a supervisory signal every 64 minutes. If the receiver does not receive a signal within the time programmed for the Wireless Supervisory Window, it will generate a zone fault. Tamper Switches There is one tamper switch on the PC5132 board. Removing the plastic cover will cause a general system tamper. 6.2 Jamming Signal Detection The PC5132 receiver detects jamming signals that can prevent the receiver from properly receiving transmissions from enrolled devices. See section 4.4 Jamming Signal Detection for information on jamming signal detection programming. 6.3 Wireless Zone Low Battery Transmission Within any transmission, the device will indicate the status of the battery. If a battery is low, the system will indicate a Device Low Battery trouble. The system will delay reporting the event to the central station for the number of days programmed for Zone Low Battery Transmission Delay in section
[370]. This will prevent unnecessary reporting of the event if the user has been instructed on how to replace batteries. 14 A D D I T I O N A L N O T E S Replacing Batteries in Wireless Devices 1. Remove the cover of the device from its back plate. This creates a tamper condition on the zone. 2. Refer to the battery installation instructions on the installation sheet of each component. Be sure to note the proper orientation of the batteries as you install them. 3. When the fresh batteries are in place, re-attach the cover to the back plate. The tamper is restored and the zone sends a battery trouble restoral signal to the PC5132. The battery trouble is now clear and the device should function normally. NOTE: When batteries in one device need to be replaced, the batteries in all devices may need to be replaced at the same time. 15 Troubleshooting S E C T I O N 7 1. When I enter the 2-digit zone number when adding a wireless device, the keypad gives me a long beep. You cannot enter ESNs unless a PC5132 wireless receiver is connected to the Keybus. See section 2 for instructions on setting up and wiring the PC5132 module. 2. I have entered the ESN for the device but when I violate the device, the zone does not show open on the keypad. Check the following:
Ensure the ESN has been entered correctly Ensure that the zone is enabled for the partition (if partition programming is used). Ensure that the wireless zone is not assigned to a zone used by PC5108 modules, an on-board zone, or a keypad zone. Ensure that the zone is programmed for something other than Null Operation, and that the wireless zone attribute is turned on. 3. When I try a module placement test I get no result or bad results. Check the following (see sections 5.1 and 5.2 for more information on testing devices):
Verify that you are testing the correct zone. Verify that the correct ESN was entered when the device was enrolled. Verify that the device is in range of the PC5132. Try testing the device in the same room as the receiver. Confirm that the PC5132 is properly connected to the Keybus (see section 2 for PC5132 set up and wiring instructions). Check that you are testing the zone correctly (see sections 5.1 and 5.2 for testing instructions). Check that the batteries are working and installed correctly. Look for large metal objects that may be preventing the signal from reaching the PC5132. The device must be located where consistent good results are obtained. If several devices show bad results, move the receiver. See section 2.2 for tips on choosing a mounting location for the PC5132. 4. The LED on the motion detector does not turn on when I walk in front of the unit. The LED is for walk test purposes only. See your WLS904-433 Instruction Sheet for walk test instructions. 16 Programming Worksheets S E C T I O N 8
[804] 5132--433 Wireless Expansion Programming 6-digit entry is required. See Section 3.1 A note on Electronic Serial Numbers for details on programming 6-digit serial numbers. Zone Serial Numbers Default = 000000
[01] Zone 1
[02] Zone 2
[03] Zone 3
[04] Zone 4
[05] Zone 5
[06] Zone 6
[07] Zone 7
[08] Zone 8
[09] Zone 9 l_____l_____l_____l_____l_____l_____l
[17] Zone 17 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[18] Zone 18 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[19] Zone 19 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[20] Zone 20 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[21] Zone 21 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[22] Zone 22 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[23] Zone 23 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[24] Zone 24 l_____l_____l_____l_____l_____l_____l l_____l_____l_____l_____l_____l_____l
[25] Zone 25 l_____l_____l_____l_____l_____l_____l
[10] Zone 10 l_____l_____l_____l_____l_____l_____l
[26] Zone 26 l_____l_____l_____l_____l_____l_____l
[11] Zone 11 l_____l_____l_____l_____l_____l_____l
[27] Zone 27 l_____l_____l_____l_____l_____l_____l
[12] Zone 12 l_____l_____l_____l_____l_____l_____l
[28] Zone 28 l_____l_____l_____l_____l_____l_____l
[13] Zone 13 l_____l_____l_____l_____l_____l_____l
[29] Zone 29 l_____l_____l_____l_____l_____l_____l
[14] Zone 14 l_____l_____l_____l_____l_____l_____l
[30] Zone 30 l_____l_____l_____l_____l_____l_____l
[15] Zone 15 l_____l_____l_____l_____l_____l_____l
[31] Zone 31 l_____l_____l_____l_____l_____l_____l
[16] Zone 16 l_____l_____l_____l_____l_____l_____l
[32] Zone 32 l_____l_____l_____l_____l_____l_____l 17 P R O G R A M M I N G W O R K S H E E T S Wireless Key Serial Numbers Default = 000000
[41] Key 01 l_____l_____l_____l_____l_____l_____l
[42] Key 02 l_____l_____l_____l_____l_____l_____l
[43] Key 03 l_____l_____l_____l_____l_____l_____l
[44] Key 04 l_____l_____l_____l_____l_____l_____l
[45] Key 05 l_____l_____l_____l_____l_____l_____l
[46] Key 05 l_____l_____l_____l_____l_____l_____l
[47] Key 07 l_____l_____l_____l_____l_____l_____l
[48] Key 08 l_____l_____l_____l_____l_____l_____l
[49] Key 09 l_____l_____l_____l_____l_____l_____l
[50] Key 10 l_____l_____l_____l_____l_____l_____l
[51] Key 11 l_____l_____l_____l_____l_____l_____l
[52] Key 12 l_____l_____l_____l_____l_____l_____l
[53] Key 13 l_____l_____l_____l_____l_____l_____l
[54] Key 14 l_____l_____l_____l_____l_____l_____l
[55] Key 15 l_____l_____l_____l_____l_____l_____l
[56] Key 16 l_____l_____l_____l_____l_____l_____l Wireless Key Function Key Options Entry Key Description Entry Key Description 00 Null Key 01-02 For Future Use 03 04 05 06 07 Stay Arm Away Arm
[Q ][9] No-Entry Arm
[Q ][4] Chime ON/OFF
[Q ][6][][4] System Test 08-12 For Future Use 16 17 18 19 20 21
[Q ][0] Quick Exit
[Q ][1] Reactivate Stay/Aways For Future Use
[Q ][7][3] Command Output #3 For Future Use
[Q ][7][4] Command Output #4 22-26 For Future Use
Disarm (OFF) 2727 13 14 15
[Q ][7][1] Command Output #1
[Q ][7][2] Command Output #2 /
Sensor Reset For Future Use 2828 2929 30 Fire Alarm Auxiliary Alarm Panic Alarm 18 P R O G R A M M I N G W O R K S H E E T S Partition 1 Wireless Key Options Default = 00
[59] Function Key 1 l____l____l Function Key 2 l____l____l Function Key 3 l____l____l Function Key 4 l____l____l Partition 2 Wireless Key Options
[60] Function Key 1 l____l____l Function Key 2 l____l____l Function Key 3 l____l____l Function Key 4 l____l____l Supervision
[81] Wireless Supervisory Window Default = 96 l____l____l The window is programmed in 15 minute increments. The default programming is 96 (x 15minutes), which is equal to 24 hours. Valid entries are (04) - (96), equal to 2 - 24 hours.
[82] Zone Device Supervision Options (1-8) Option ON Option OFF Default = ON l________l Option 1 l________l Option 2 l________l Option 3 l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Zone 01 Supervision enabled Zone 02 Supervision enabled Zone 03 Supervision enabled Zone 04 Supervision enabled Zone 05 Supervision enabled Zone 06 Supervision enabled Zone 07 Supervision enabled Zone 08 Supervision enabled
[83] Zone Device Supervision Options (9-16) Default = ON l________l Option 1 l________l Option 2 l________l Option 3 l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Option ON Zone 09 Supervision enabled Zone 10 Supervision enabled Zone 11 Supervision enabled Zone 12 Supervision enabled Zone 13 Supervision enabled Zone 14 Supervision enabled Zone 15 Supervision enabled Zone 16 Supervision enabled 19 Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Option OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled P R O G R A M M I N G W O R K S H E E T S
[84] Zone Device Supervision Options (17-24) Default = ON l________l Option 1 l________l Option 2 l________l Option 3 l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Option ON Zone 17 Supervision enabled Zone 18 Supervision enabled Zone 19 Supervision enabled Zone 20 Supervision enabled Zone 21 Supervision enabled Zone 22 Supervision enabled Zone 23 Supervision enabled Zone 24 Supervision enabled
[85] Zone Device Supervision Options (25-32) Default = ON l________l Option 1 l________l Option 2 l________l Option 3 l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Option ON Zone 25 Supervision enabled Zone 26 Supervision enabled Zone 27 Supervision enabled Zone 28 Supervision enabled Zone 29 Supervision enabled Zone 30 Supervision enabled Zone 31 Supervision enabled Zone 32 Supervision enabled Option OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Option OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled
[90] Other Options Default = OFF l________l Options 1-5 l________l Option 6 l________l Option 7 l________l Option 8 Option OFF Option ON For future use Sensitive RF jamming detection RF Jam Detect Disabled RF Jam Detect Enabled Global Placement Test Normal RF jamming detection Individual Placement Test
[91] Wireless Keys (1-8) Partition Assignments Default = OFF l________l Option 1 l________l Option 2 l________l Option 3 Option ON Wireless Key 01 on partition 2 Wireless Key 02 on partition 2 Wireless Key 03 on partition 2 Option OFF On partition 1 On partition 1 On partition 1 20 P R O G R A M M I N G W O R K S H E E T S l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Wireless Key 04 on partition 2 Wireless Key 05 on partition 2 Wireless Key 06 on partition 2 Wireless Key 07 on partition 2 Wireless Key 08 on partition 2
[92] Wireless Keys (9-16) Partition Assignments Default = OFF l________l Option 1 l________l Option 2 l________l Option 3 l________l Option 4 l________l Option 5 l________l Option 6 l________l Option 7 l________l Option 8 Option ON Wireless Key 09 on partition 2 Wireless Key 10 on partition 2 Wireless Key 11 on partition 2 Wireless Key 12 on partition 2 Wireless Key 13 on partition 2 Wireless Key 14 on partition 2 Wireless Key 15 on partition 2 Wireless Key 16 on partition 2 On partition 1 On partition 1 On partition 1 On partition 1 On partition 1 Option OFF On partition 1 On partition 1 On partition 1 On partition 1 On partition 1 On partition 1 On partition 1 On partition 1 RF Jamming Detection
[93] RF Jam Detect Zone Default = 00 l____l____l Select an unused zone that will be violated when a jamming signal is detected. (Valid entries = 01 - 32, 00 = RF Jam detect disabled.) P R O G R A M M I N G W O R K S H E E 21 Guidelines for Locating Smoke Detectors A P S P E E C N T I D O I N X 9 A Experience has shown that all hostile fires in family living units generate smoke to a greater or lesser extent. Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases. In existing homes, NFPA Standard 72 requires that a smoke detector be installed outside each sleeping area and on each additional story of the family unit. On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULS-S553-M86 or other appropriate national standards for installation recommendations. Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke. Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from entering the unit. Do not locate detectors in areas of high humidity. Do not locate detectors in areas where the temperature rises above 38oC (100oF) or falls below 5oC (41oF). Smoke detectors should always be installed in accordance with NFPA 72, the National Fire Alarm Code. Smoke detectors should always be located in accordance with:
Paragraph 2-2.1.1.1 of NFPA 72:Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In new construction, a smoke detector also shall be installed in each sleeping room. Paragraph 2-2.1.1.2 of NFPA 72:Split level arrangement. Smoke detectors are required where shown. Smoke detectors are optional where a door is not provided between living room and recreation room. The Smoke Detector is designed to use Eveready Energizer E91 Alkaline Batteries. Do not use other brands of batteries with the Smoke Detector. Using brands other than the Eveready Energizer will void UL approval, and may affect the systems operation. 22 Index D E X I N A add device 4 wireless key 5, 11 antenna 3 B batteries replacing 13 buttons programming 5 C connect Keybus 3 receiver 3 D default module 9 panel 9 delete device 9 devices 2 adding 4 removing 9 distance from control panel 1 E electronic serial number 4 enroll device 4 PC5132 7 wireless key 4 ESN 4 F factory default 9 frequency 1 function keys 5 G global placement test 10 I individual placement test 11 interference 3 J jamming signal detection 8, 12 K Keybus 3 L location choosing 3 low battery devices 12 M mount devices 11 PC5132 11 N number electronic, serial 4 P partition program-
ming 7 wireless keys 5 placement PC5132 3 test 10 power 3 problems 12 23 R removing device 9 module 7 RF jamming 9 S serial number 4 slot number wireless key 5 supervision DEOL 8 device 8 disable 7 module 7 window 8 T testing door/window contact 10 global 10 individual 11 motion detector 10, 11 PC5132 10 placement 10 trouble 12 troubleshooting 17 W wireless key access codes 6 activating outputs 6 arming/disarming 6 enrolling 4 identifying 6 programming 4 Z zone adding 4 attribute 7 numbers 4 programming 7 wireless 7 LIMITED WARRANTY Digital Security Controls Ltd. warrants the original pur-
chaser that for a period of twelve months from the date of purchase, the product shall be free of defects in ma-
terials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The original owner must promptly notify Digital Security Controls Ltd. in writing that there is defect in material or work-
manship, such written notice to be received in all events prior to expiration of the warranty period. International Warranty The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital Security Controls Ltd. shall not be responsible for any customs fees, taxes, or VAT that may be due. Warranty Procedure To obtain service under this warranty, please return the item(s) in question to the point of purchase. All autho-
rized distributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls Ltd. must first obtain an authorization number. Digital Secu-
rity Controls Ltd. will not accept any shipment whatso-
ever for which prior authorization has not been obtained. Conditions to Void Warranty This warranty applies only to defects in parts and work-
manship relating to normal use. It does not cover:
damage incurred in shipping or handling;
damage caused by disaster such as fire, flood, wind, earthquake or lightning;
damage due to causes beyond the control of Digital Security Controls Ltd. such as excessive voltage, me-
chanical shock or water damage;
damage caused by unauthorized attachment, alter-
ations, modifications or foreign objects;
damage caused by peripherals (unless such peripher-
als were supplied by Digital Security Controls Ltd.);
defects caused by failure to provide a suitable instal-
lation environment for the products;
damage caused by use of the products for purposes other than those for which it was designed;
damage from improper maintenance;
damage arising out of any other abuse, mishandling or improper application of the products. Digital Security Controls Ltd.s liability for failure to repair the product under this warranty after a reason-
able number of attempts will be limited to a replace-
ment of the product, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls Ltd. be liable for any spe-
cial, incidental, or consequential damages based upon breach of warranty, breach of contract, negli-
gence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of prof-
its, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchasers time, the claims of third parties, includ-
ing customers, and injury to property. Disclaimer of Warranties This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a par-
ticular purpose) And of all other obligations or li-
abilities on the part of Digital Security Controls Ltd. Digital Security Controls Ltd. neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liabil-
ity concerning this product. This disclaimer of warranties and limited war-
ranty are governed by the laws of the province of Ontario, Canada. WARNING: Digital Security Controls Ltd. recom-
mends that the entire system be completely tested on a regular basis. However, despite frequent test-
ing, and due to, but not limited to, criminal tam-
pering or electrical disruption, it is possible for this product to fail to perform as expected. Out of Warranty Repairs Digital Security Controls Ltd. will at its option re-
pair or replace out-of-warranty products which are returned to its factory according to the following con-
ditions. Anyone returning goods to Digital Security Controls Ltd. must first obtain an authorization num-
ber. Digital Security Controls Ltd. will not accept any shipment whatsoever for which prior authoriza-
tion has not been obtained. Products which Digital Security Controls Ltd. deter-
mines to be repairable will be repaired and returned. A set fee which Digital Security Controls Ltd. has predetermined and which may be revised from time to time, will be charged for each unit repaired. Products which Digital Security Controls Ltd. deter-
mines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of the replacement product will be charged for each replacement unit. N O T E S N O T E S FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC helpful: How to Identify and Resolve Radio/Television Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4. This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numrique de la Classe B respecte toutes les exigences de rglement sur le matriel brouilleur du Canada. AVIS: Ltiquette de lIndustrie Canada identifie le matriel homologu. Cette tiquette certifie que le matriel est conforme certaines normes de protection, dexploitation et de scurit des rseaux de tlcommunications. Industrie Canada nassure toutefois pas que le matriel fonctionnera la satisfaction de lutilisateur. Avant dinstaller ce matriel, lutilisateur doit sassurer quil est permis de le raccorder aux installations de lentreprise locale de tlcommunication. Le matriel doit galement tre install en suivant une mthode accepte de raccordement. Labonn ne doit pas oublier quil est possible que la conformit aux conditions nonces ci-dessus nempchent pas la dgradation du service dans certaines situations. Les rparations de matriel homologu doivent tre effectues par un centre dentretien canadien autoris dsign par le fournisseur. La compagnie de tlcommunications peut demander lutilisateur de dbrancher un appareil la suite de rparations ou de modifications effectues par lutilisateur ou cause de mauvais fonctionnement. Pour sa propre protection, lutilisateur doit sassurer que tous les fils de mise la terre de la source dnergie lectrique, les lignes tlphoniques et les canalisations deau mtalliques, sil y en a, sont raccords ensemble. Cette prcaution est particulirement importante dans les rgions rurales. AVERTISSEMENT: Lutilisateur ne doit pas tenter de faire ces raccordements lui-mme; il doit avoir recours un service dinspection des installations lectriques, ou un lectricien, selon le cas. Lindice de charge (IC) assign a chaque dispositif terminal indique, pour viter toute surcharge, le pourcentage de la charge totale qui peut tre raccorde un circuit tlphonique boucl utilis par ce dispositif. La terminaison du circuit boucl peut tre constitue de nimporte quelle combinaison de dispositifs, pourvu que la somme des indices de charge de lensemble des dispositifs ne dpasse pas 100. LIndice de charge de ce produit est 2. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecom-
munications network protective, operational and safety require-
ments. Industry Canada does not guarantee the equipment will operate to the users satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommu-
nications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degra-
dation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications com-
pany cause to request the user to disconnect the equipment. User should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100. The Load Number of this unit is 2. 2000 Digital Security Controls Ltd. Toronto, Canada 1-800-387-3630 www.dscgrp.com Printed in Canada 29005043 R001
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2001-02-05 | 433.92 ~ 433.92 | CYY - Communications Receiver used w/Pt 15 Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2001-02-05
|
||||
1 | Applicant's complete, legal business name |
Digital Security Controls Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0006834485
|
||||
1 | Physical Address |
3301 Langstaff Road
|
||||
1 |
Concord, Ontario, N/A L4K 4L2
|
|||||
1 |
Canada
|
|||||
app s | TCB Information | |||||
n/a | ||||||
app s | FCC ID | |||||
1 | Grantee Code |
F53
|
||||
1 | Equipment Product Code |
01NB5132
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
D******** N******
|
||||
1 | Title |
Approvals Manager
|
||||
1 | Telephone Number |
905-7******** Extension:
|
||||
1 | Fax Number |
905-7********
|
||||
1 |
d******@dsc.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
KTL OTTAWA INC.
|
||||
1 | Name |
R****** C****** D******
|
||||
1 | Physical Address |
3325 RIVER ROAD
|
||||
1 |
OTTAWA
|
|||||
1 |
OTTAWA, K1V 1H2
|
|||||
1 |
Canada
|
|||||
1 | Telephone Number |
613-7******** Extension:
|
||||
1 | Fax Number |
613-7********
|
||||
1 |
r******@ktlcanada.com
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
KTL OTTAWA INC.
|
||||
1 | Name |
R****** C****** D****
|
||||
1 | Physical Address |
3325 RIVER ROAD
|
||||
1 |
OTTAWA
|
|||||
1 |
OTTAWA, K1V 1H2
|
|||||
1 |
Canada
|
|||||
1 | Telephone Number |
613-7******** Extension:
|
||||
1 | Fax Number |
613-7********
|
||||
1 |
r******@ktlcanada.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | CYY - Communications Receiver used w/Pt 15 Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | PC5132A-433 & P5132A-433 Receiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Nemko Canada Inc.
|
||||
1 | Name |
S******** B********
|
||||
1 | Telephone Number |
613-7********
|
||||
1 | Fax Number |
613-7********
|
||||
1 |
s******@nemko.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | 433.92000000 | 433.92000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC