PACKAGE CONTENTS Door/
Window Sensor Adhesive Fastener
(Double-sided tape)
(Qty. 3 pieces, perforated) Quick Start Guide DOOR/WINDOW SENSOR QUICK START GUIDE For all your customer needs, go to SAGEbyHughes.com LIMITED WARRANTY One year Limited Warranty. Limited Warranty details are available at SAGEbyHughes.com/warranty. p/n 209088 product is designed in the United States and manufactured in India. mentioned are the Trademarks of their respective owner(s). This EchoStar Technologies L.L.C. Other products, brands, and companies 80112. All rights reserved. EchoStar is a registered trademark of Copyright 2016. EchoStar Technologies L.L.C., Englewood, Colorado DOOR/WINDOW SENSOR QUICK START GUIDE REGULATORY INFORMATION This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with Part 15 of the FCC Rules and with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de license. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If none of the remedies stops the radio interference, you should contact a licensed radio/
television technician, your satellite dealer, or visit SAGEbyHughes.com for assistance. Product must be installed at least 20 cm (~8 inches) from typical person locations per FCC RF exposure regulations. Do not make changes or modifications to this equipment. This could void the users authority to operate the equipment. SETUP AND INSTALLATION This sensor allows you to set-up and control up multiple sensors using Zigbee signals that communicate with your SAGE Hub and that you can control and modify using your TV and mobile devices. To begin installing your SAGE Door/Window Sensor, follow the instructions below. 1 Using your SAGE remote, press HOME. 2 Select Settings. 3 4 Select Sensors. Select Add Devices. 5 6 Select Door/Window Sensor. Follow the SAGE Hub on-screen prompts to install and set up your SAGE Door/Window Sensor, pair it, and establish the rules for it. IMPORTANT SAFETY NOTICE: The installation instructions on your SAGE Hub include important safety information. Do not begin installation of your sensor until you have carefully reviewed this information. Installation of your device without reviewing these instructions may result in electric shock, which could cause injury or death. REPLACING THE BATTERY When the Low Battery Warning appears for the SAGE Door/Window Sensor, use these instructions to replace the battery. Note: The SAGE Door/Window Sensor takes a CR2032 3V Lithium battery. Note: Dispose of used batteries at a retail recycling drop-off in accordance with local codes. and then dispose of the battery properly (see figure 2). of the cover and gently pulling outward (see figure 1). 1 Remove the front cover by grasping grips toward the top 2 Remove the battery by lifting up on its lower right side, 3 Slide the new battery under the ledge on the left side of 4 Replace the front cover by slotting it correctly in the side 5 You may need to re-pair the sensor with the SAGE the terminal, ensuring polarity is correct (see figure 3). rails and then pushing it closed (see figure 4). Hub. 1 3 2 4