Packing List Wireless Earphone User Manual Product Model: QFIT 1. Bluetooth Earphone----------------------------------------------------------- 1 set 2. Charging cable ------------------------------------------------------------------ 1 set 3. User's manual ------------------------------------------------------------------- 1 copy Product Specifications Bluetooth:
V 4.2 (Single Mode) IC (What does this stand for) JL Frequency:
SNR 20Hz-20KHz 105dB/3dB Speaker specifications (What does this stand for) 4.0*1.5mm Signal to Noise Ratio:
-42dB/3dB Support mode (What does this stand for) A2DP / HFP / HSP / AVRCP / L2CAP Working voltage (What does this stand for) 3.7V0.5V Playback Time:
Standby Time:
Up to 3 hours Up to 160 hours Charging Current:
60mA Battery Type:
3.7V Li-polymer rechargeable battery Battery Charging Voltage:
5V DC max. Main function Main Material Operating Instructions Initial Pairing Wireless Bluetooth, hands-free with mic ABS 1. Press & hold the POWER button for 3 seconds to turn ON until the red and blue lights flash (This means the headset has entered pairing mode) 2. Turn your Bluetooth ON (On your device), search and select headset. 3. Click and pair. 4. After successfully pairing, you will hear a tone. The headset light will flash blue. Please Note: If required, enter the password 0000. Select OK or YES to pair your device. How to Power ON Your Headset Press & hold the POWER button for 3 seconds to turn on the headset. How to Power OFF Your Headset Once the headset is on, press & hold the POWER button for 3 seconds to turn off the headset. Auto Re-Connect 1. Turn your devices Bluetooth ON, before turning on the headset 2. The headset will connect automatically to the last paired device Play/Pause Music In standby mode, click the POWER button to play music, and press the POWER button to pause. Switch Songs When playing music, press the plus (+) or minus (-) buttons to switch songs up and down. Adjust Volume To adjust the volume on headset, press and hold the plus (+) or minus (-) button to increase or decrease the volume. Answer/End/Reject Call Answering Call: During an incoming call, click the POWER button to answer the call. Ending Call: When on a call, click the POWER button to hang up the phone. Reject Call: During an incoming call, Press and hold the POWER button for 2 seconds to refuse a call. Redial While on standby or playing music, double-click the POWER button to dial the last call in your call log. Low battery prompt When the headset battery is low, you will hear a battery low tone. Light Indicator Red Light: When charging (when fully charged red light will go out). Blue Light: flashes slowly when music is playing Warnings 1. Charge in a safe environment. 2. When the headset light turns blue, please separate the headset from the charging cable as soon as possible to avoid damage to the headset. 2. When using the headset to listen to music or place calls, please pay attention the volume. Listening at a high volume may affect hearing. 3. To avoid damage to the battery, keep the battery fully charged when the product is not used for a long time 4. Avoid leaving headset in direct sunlight or in a dusty environment. Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.