FCC ID: VZ4-360204N Doran TPMS Sensor for Truck

User manual User Manual 1. General Description Tire pressure sensor is composed of RF chip, battery, antenna and Rf matching network. It is applied to monitor tire pressure, temperature and acceleration and the tire data is transmitted via center frequency 434.1MHz. 2. Operation Functions 2.1 Data Accuracy

(measure @0~70) Temperature:+/-2 Pressure: +/-2psi 2.2 TPMS chip Chip model#: Freescale FXTH87EK116 Working temperature: -40~120 Operation pressure range: 0~188psi Working Voltage: 2.3~3.6VDC 2.3 RF chip Chip model: MAX1479ATE Max. RF signal strength: 10dBm 2.4 Battery information Manufacturer: F0188-LF (Li/SOCl2) Capacity: 400mAh Normal voltage: 3.6V Extreme voltage:3.8V Operation temperature: -55~125 Estimated life span: 6 years 3. Environmental requirement The sensor will be mounted onto the valve stem. For the OTR model, it has the built-in filter which can work with the tire that has the liquid inside. Temperature requirement: -40~125 for storage

-40~120 for operation Vibration: Refer to ISO16750-3, 4.1.2.9 Test IX Commercial vehicle, unsprung masses IP protection: IP6k9k (with sensor screwed onto valve stem) Codes for Climatic loads: E 4. PMN: Doran TPMS Sensor for Truck User manual 5. Sensor Installation Instructions 5.1 Program the sensor ID into the receiver To make TPMS products work properly, the sensor ID must be programmed into the receiver for each wheel to be monitored. The following operations are performed on the receiver. a) Press the P button to enter the program mode. Select the wheel position and press S button to enter the sensor ID. b) Input the last three digits of the sensor ID into the receiver by navigating the arrow keys. c) Press the S button for three seconds to confirm the information. If there are more wheels to be programmed, repeat steps a-c in above until all the wheels have the sensor ID entered. Finish the programming process by pressing the P button for 5 seconds to quit the program mode. 5.2 Install the sensor onto the valve stem Once the receiver is prepared and programmed, simply screw the sensor onto the valve stem in each wheel. Be sure to inspect and replace any defective or cracked valve stems before installing the sensors. If replacements are necessary, suggest replacing the valve stems with a Brass or Stainless-Steel stem. It does improve the life of the stem due to premature failure from drying out and cracking. Inferior stems have been found in the market and can cause extensive damage. The sensor should he tightened only by hand not with a tool. Use a firm grip and tighten the sensor. When the sensor seal makes contact with the end of the valve stem only tighten the sensor an additional 1/2 turn. This should be tight enough to seal the sensor and hold it in place. Check for leaks with a soapy solution. The monitor or receiver will begin to receive and recognize the sensors, and it will display the wheel positions as they are received on the screen. 6. Manufacturer information Company name: Doran Manufacturing LLC Company address: 2851 Massachusetts Avenue Cincinnati, OH 45225 USA Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device Le present appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. 2. si le brouillage est susceptible den compromettre le fonctionnement. lappareil ne doit pas produire de brouillage;

lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl.

DORAN MANUFACTURING, LLC. Cover Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: VZ4-360204N Please be notified that we, the undersigned, DORAN MANUFACTURING, LLC. declares that the product which bears the above FCC ID is also compliant with the FCC requirements for Suppliers Declaration of Conformity(sDOC). And the sDOC procedure shall be carried out prior to marketing the device in the US. Sincerely, _________________ Name: KEVIN SHEN Title: VP of Product Development and Quality Email: shen_kevin@doranmfg.com Date: 2023-01-16

Doran Manufacturing LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02-15-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: VZ4-360204N Doran Manufacturing LLC (the applicant) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0017376450 Name: Doran Manufacturing LLC Address: 2851 Massachusetts Avenue Cincinnati, OH 45225 USA Contact Person: Kevin Shen Tel.: 13916851310 Email: shen_kevin@doranmfg.com Sincerely, Doran Manufacturing LLC Kevin Shen

(Applicant signature) Rev 1/26/2023

Doran Manufacturing LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February-06-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: VZ4-360204N.

[Doran Manufacturing LLC] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature)

(Applicant printed name) Kevin Shen Rev 1/26/2023 Doran Manufacturing LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February-06-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: VZ4-360204N

[Doran Manufacturing LLC] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Applicant signature)

(Applicant printed name) Kevin Shen Rev 1/26/2023

DORAN MANUFACTURING, LLC. Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: VZ4-360204N Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

1. Block Diagram 2. Schematics 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: KEVIN SHEN Title: VP of Product Development and Quality Email: shen_kevin@doranmfg.com Date: 2023-01-16

DORAN MANUFACTURING, LLC. Declaration of Authorization We Name: DORAN MANUFACTURING, LLC. Address: 2851 Massachusetts Avenue Cincinnati, OH 45225 United States Declare that:

Name Representative of agent: Marlin Chen Agent Company name:

Address:

MRT Technology (Suzhou) Co., Ltd D8 Building, No.2 Tian'edang Rd., Wuzhong Economic Development Zone Suzhou China City:

Country:

is authorized to apply for Certification of the following product(s):

Doran TPMS Sensor for Truck VZ4-360204N 3604, 3602, 3603 Product:

FCC ID:

Model No.:

Sincerely, _ ________________ Name: KEVIN SHEN Title: VP of Product Development and Quality Email: shen_kevin@doranmfg.com Date: 2023-01-16

DORAN MANUFACTURING, LLC. Declaration letter For our business issue and marketing requirement, we would like to list different model numbers as following:

Model No.: 3604, 3602,3603 Model Difference:

Test device 3604 has low- frequency inductor, and model 3602 does not have low-

frequency inductor, which does not affect radio parameters. Model 3603 is the same as 3604 except different appearance, model number and software coding format, which does not affect radio parameters. _________________ Name: KEVIN SHEN Title: VP of Product Development and Quality Email: shen_kevin@doranmfg.com Date: 2023-01-16

DORAN 07/07/2021 Subject: Authorized signatures Kevin Shen (Dorans Vice President of Product Development & Quality) is authorized by DORAN MANUFACTURING, LLC. to sign documents for FCC product approval under FCC Grantee code VZ4, and ISED product approval under ISED registration 12007A on behalf of the company. Regards

ze Samocki, President DORAN MANUFACTURING, LLC.