User manual
User Manual
3602, 3602N
1. General Description
Tire pressure sensor is composed of RF chip, battery, antenna and Rf matching
network. It is applied to monitor tire pressure, temperature and acceleration and the
tire data is transmitted via center frequency 434.1MHz.
2. Operation Functions
2.1 Data Accuracy
(measure @0~70℃)
⚫ Temperature:+/-2℃
⚫ Pressure: +/-2psi
2.2 TPMS chip
⚫ Chip model#: Freescale FXTH871511DT1
⚫ Working temperature: -40~120℃
⚫ Operation pressure range: 5~200psi
⚫ Working Voltage: 2.2~3.6VDC
2.3 RF chip
⚫ Chip model: Maxim TDK5110F
⚫ Max. RF signal strength: 10dBm
2.4 Battery information
⚫ Manufacturer: EVE EF651615T/2P-B (Li-SOCL2)
⚫ Capacity: 400mAh
⚫ Normal voltage: 3.6V
⚫ Operation temperature: -40~125℃
⚫ Estimated life span: 9 years
3. Environmental requirement
The sensor will be mounted onto the valve stem. For the OTR model, it has the
built-in filter which can work with the tire that has the liquid inside.
⚫ Temperature requirement: -40℃~125℃ for storage
-40℃~105℃ for operation
⚫ Vibration: Refer to ISO16750-3, 4.1.2.9 Test IX — Commercial vehicle,
unsprung masses
IP protection: IP6k9k (with sensor screwed onto valve stem)
⚫
⚫ Codes for Climatic loads: E
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio / TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device
Le present appareil est conforme aux CNR d’Industrie Canada applicable aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1.
2.
si le brouillage est susceptible d’en compromettre le fonctionnement.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies
pour un environnement non contrôlé.
l’appareil ne doit pas produire de brouillage;
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme