FCC ID: Q8SRTPLUS Wireless door lock

Saflok RT/RT Plus Installation instructions PK3720-T - 2022 - 06 EN Table of Contents Saflok RT/RT Plus ASM, ESM, ASM Auto Deadbolt Mortises &

Cylindrical Models 23/8" and 23/4" Backset Stand Alone (79S), Ambiance RX Ready (79R), Ambiance RX

(79Z,Y,Q), and Escape Return (79N) Models Note: This installation Guide is for Saflok RT and RT Plus lock. Images of the lock may vary depending on installed options. 03 04 04 06 07 08 08 09 10 11 12 13 21 21 24 26 27 27 28 28 28 28 29 30 31 33 33 33 34 1. Introduction and Disclaimers 2. Checklist and Exploded Views 2.1. Parts and Tools List 2.2. ASM/ESM 2.3. Autodeadbolt ASM Inside Trim Assembly Installation of Standard ASM or ESM Models 3.1. Check the Mortise Handing 3.2. Install the Strike 3.3. Install the Mortise 3.4. Install the Outside Housing & Inside Trim Assembly without key override 3.5. Reversing the Outside Lever Installing the Mechanical Override Model Appendices A. Mortise Models A.1. Reversing the Mortise Handing 3. 4. A.1.1. Reversible ASM A.1.2. Reversible ESM A.2. Additional Steps for Autodeadbolt ASM A.3. Additional Steps for ASM Office A.4. Additional Steps for ASM/ESM Storeroom B. Cylindrical Models B.1. Installing Cylindrical Models B.1. Install the Strike B.2. Install the Latch B.3. Install the Cylindrical Unit B.4. Inside Trim Assembly B.5. Install Outside Housing &

Trim Assembly C. Escape Return Model (79N) C.1. ASM/ESM & ADB Inside trim assembly for 79N C.2. Installation of extension spring on inside trim assembly Installation Guide Lexicon 2022 Saflok. All trademarks and registered trademarks are the property of their respective owners. 2 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 1 Introduction and Disclaimers WARNING CAUTION IMPORTANT Target Audience WARNING Definition of Terms CAUTION Technical Assistance IMPORTANT Please read and follow all directions carefully. These instructions are designed for use by maintenance professionals or lock installers who are familiar with common safety practices and competent to perform the steps described. Kaba is not responsible for damage or malfunction due to incorrect installation however arising. In these instructions, the term ASM refers to American Standard Mortise, and ESM refers to European Slim Mortise, and ADB refers to Autodeadbolt Mortise. For technical assistance, call: 1 800 999 6213 WARNING Carefully inspect windows, doorframe, door, etc. to ensure that the recommended procedures will not cause damage. dormakaba standard warranty does not cover damages caused by installation. CAUTION For all mortise models the gap between the mortise front plate and the strike must not exceed 1/4 IMPORTANT Door Door Frame Mortise WARNING Max. 1/4"

CAUTION IMPORTANT Wear safety glasses when making the holes. Saflok RT/RT Plus Installation Guide PK3720_T 06-22 3 2 Checklist and Exploded Views 2.1 Parts and Tools List Each lockset includes:

(A) Ouside lever handle

(or) Parts for Mechanical override model only:

(A1) Outside lever handle

(B1) Outside housing

(C1) Cylinder plug

(D1) Cylinder

(E1) Cylinder cap

(E2) Instruction sheet How to attach lever on lock"

(B) Outside housing

(C) Battery holder with 3 AA Alkaline batteries

(D) Mortise (ASM only shipped assembled with face plate (P) and 2 x 8-32 x 1/4" screws (D12))

(or) Parts for cylindrical models (see illustrations in appendix B):

- cylindrical latch (see Section B.2)

- cylindrical unit assembled with one pair of screws & 3 spacers

- four (4) other pairs of screws & three (3) spacers in hardware bag

- additional extension spring

- storeroom function locking screw and nut Inside trim assembly, details depend on lock model (see 2.2, 2.3, 2.4)

(E)

(N) Outdoor gasket included in cylindrical latch locks only. Order separately for locks with mortise. ESSENTIAL FOR OUTDOOR INSTALLATIONS P/N: 033-512017-1 4 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 2 Checklist continued Parts inside hardware bag:

(C1) 1x Cylinder plug (for K model only)

(E1) 1x Cylinder cap (for K model only) 1x Thumbturn (hex) spindle

(F) 1x Square spindle

(G) 1x Torx-head screw

(H) 3x Mounting screws (10-24, 1/8 Hex Head) or (12-24, 1/8" Hex Head for recent models only)

(I) 2x Machined screws (12-24X 1/2" Philips) & 2 wood screws (#12 X 1" Philips)

(J) 1x Strike kit (screws, strike and ASM or Cylindrical dustbox)

(K) 1x Extension spring

(L)

(M) 1x Parts required to control thumbturn motion for (ASM and ESM Storeroom, ASM Office See appendix A3 & A4)

(S) 3x Spacers

(Y) 4x Pairs of Flat Head Screws 10-24 (for cylindrical only, see appendix B door thickness table)

(Z) 3x Spacers (for cylindrical only, see appendix B door thickness table) Tools Required:

Awl or center punch 2 1/8" (54mm) hole saw (Cylindrical Only) Safety glasses 1/2" (13mm) chisel 1/8" (3mm) drill bit 1/4" (6.5mm) drill bit (ESM only) 1/2" (13mm) drill bit 3/4" (22mm) drill bit or hole saw 1" (25.4mm) drill bit or hole saw Drill Hammer Rubber mallet Small flat screwdriver Torx screwdriver (T-15) (760 Series) Phillips screwdriver (#2) Fine steel file Mortising machine Mortise face plate router template Lock Template Cleaning supplies (drop cloth, vacuum) Adjustable square Tape measure Pencil Tape Installation Jig (Recommended) 1/8" Allen Key CAUTION 5/64" Allen Key WARNING Router IMPORTANT For doors more than 2 1/2" thick up to 3 3/4", order the appropriate hardware bag to receive the correct length of spindles and mounting screws. Part# 062-512868-XXX; (XXX = choice of finish). For outdoor installations, order gasket 033-512017-1. Gasket comes standard with cylindrical locks and ultra finish locks. Saflok RT/RT Plus Installation Guide PK3720_T 06-22 5 U X B N V I 2 Exploded Views 2.2 ASM/ESM (For Cylindrical, see Appendix B) A B1 C H F G C1 D1 W S E S L D12 D J J P K A1 E1 Notes: American Standard Mortise illustrated. 6 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 2 Exploded Views 2.3 Autodeadbolt ASM Inside Trim Assembly NOTE:

The inside trim assembly (E) for autodeadbolt models includes the parts (E3, E4, E5, E17)shown, assembled at the factory. For ASM Office and ASM/ESM Store-room models, only some of the parts (E) are used. See instructions in Appendix A. Parts (E3, E4, E5, E17) also available separately (kit #062-

510484-K) to convert the standard lock to Autodeadbolt ASM, ASM Office or ASM/ESM Storeroom functions. E5 E E4 E3 E17 Fully assembled view Saflok RT/RT Plus Installation Guide PK3720_T 06-22 7 3 Installation of Standard ASM or ESM Models

(for cylindrical see Appendix B) WARNING 3.1 Check the Mortise Handing CAUTION Compare the mortise with the diagram below. If the mortise is the correct handing for the door, continue with step 3.2. Door Handing (Top View) IMPORTANT ASM Refer to Appendix A.1 to change the handing of a field-re-

versible mortise. Right Hand (RH) Left Hand (LH) Left Hand Reverse (LHR) dormakaba Canada Inc. 7301 Decarie Blvd. Montreal Quebec Canada H4P 2G7 0432-CPR-00072-06.01 22 EN 12209: 2003/AC:2005 3S510G3H010 None ESM MORTISE dormakaba Canada Inc. 7301 Decarie Blvd. Montreal Quebec Canada H4P 2G7 0432-CPR-00072-06.01 22 EN 12209: 2003/AC:2005 3M510G4H010 None ASM MORTISE For LH (left hand) and RHR (right hand reverse) For RH (right hand) and LHR (left hand reverse) ESM Right Hand Reverse (RHR) For LH (left hand) and RHR (right hand reverse) For RH (right hand) and LHR (left hand reverse) 8 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 3 Installation of Standard ASM or ESM Models

(for cylindrical see Appendix B) 4. Position the strike against the door frame and align it with the mounting screw holes. Trace the outline of the strike. WARNING 3.2 Install the Strike 1. Align the paper template on the door frame at the desired CAUTION handle height (

), and along the vertical center line of the mortise (CL), which is also the center line of the door edge, allowing for any bumpers on the door frame. IMPORTANT Respect applicable building codes regarding handle height. Note that the centerline of an ESMmortise does NOT pass through the screw holes on the strike.

(CL) 5. Remove material from within the strike outline so that the strike will be flush with the door frame. 2. Mark the locations of the dust box cutout and mounting screws for the strike. 3. Create the dust box pocket and chisel out the strike contour in the door frame, and drill the pilot holes for the mounting screws (dimensions and depths marked on template). 6. For ASM, install the dust box (optional for wood door frames, required for metal door frames), and check the strike handing on the template. For ASM and ESM install the strike using the screws provided. Use wood screws for wood frames and machined screws for steel frames. WARNING CAUTION IMPORTANT When strike is installed on wood frames under one inch thick, wood screws supplied are not adequate. use screws of effi-

cient length to engage the structural stud behind the frame. Use only the strike and dust box supplied. Use of non-ap-

proved parts may void the warranty. Saflok RT/RT Plus Installation Guide PK3720_T 06-22 9 WARNING 3 Installation of Standard ASM or ESM Models

(for cylindrical see Appendix B) CAUTION 3.3 Install the Mortise (for cylindrical, see Appendix B) IMPORTANT If using the installation jig to pre-

pare the door, refer to the instruc-

tions provided with the jig, then proceed with step 4 below. 1. Mark the handle (

) height on the edge of the door, as de-

termined directly the strike. from For ASM, the axis of rotation of the handle is level with the bottom lip of the strike. For ESM, the axis of rotation of the handle is 11/4" above the bot-

tom lip of the strike. ESM Strike ASM Strike 2. Align the template along the vertical center line of the mor-

tise (CL) at the desired handle height, and tape it to the door. Mark all holes and cutouts for the mortise in the edge of the door and remove the template.

(ESM) 3 5 4. Prepare the cut-outs for the mortise in the edge of the door using a mortising machine, router and chisel (for di-

mensions, refer to template).

(CL) Door Ensure clearance is provided for moving latch parts as indi-

cated on the template. RH/LHR (ASM shown) LH/RHR 5. Drill the holes in the sides of the door (for dimensions, refer to template). 11/4"

Drill from both sides of the door to prevent unsightly dam-

age. 6. For ASM only, check the bevel of the mortise. If adjust-

ment is required, loosen bevel screws (R) and adjust mor-

tise front plate angle to match the bevel of the door. Re-

tighten screws. For models 79R, 79Z, 79Y, 79Q slide the ajar switch cable of the mortise (V) through the hole at the top of the mortise pocket. The cable must go through the outside of the door for connection in the next step. Install the mortise with 2 screws (J). Use wood screws for wood doors and machined screws for steel doors. Install mortise faceplate (P) with the two 8-32 x 1/4" screws provided (D12). Hole at the top Mortise Pocket WARNING CAUTION V R J P D12 R Logo 2 4 The ESM faceplate must be installed so you can read the logo (see arrow in figure above right-side-up for proper op-

eration.) 3. Locate the two sets of vertical fold lines on the template allowing you to adjust the positioning of the template de-

pending on the bevel of the door. If the door has no bevel, fold the template along the solid lines. Align the fold with the edge of the door and mark the holes for the lock. Repeat on the other side of the door. IMPORTANT If the door has a 3 bevel, fold and align the dashed line marked H" on the template with the higher-beveled edge of the door and mark the lock holes on that side of the door. Repeat on the side with the lower-beveled edge using the dashed line marked L". Remove the template. 10 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 3 Installation of Standard ASM or ESM Models

(for cylindrical see Appendix B) 3.4 Install the Outside Housing and Inside Trim Assembly Without Key Override (for locks with mechanical key override please refer to section 4). A- For Mortise U X V E 1. Install the gasket (N) (if required) on the outside housing prior to assembly, aligning the notch in the gasket with the battery compartment. See page 4 for gasket information. WARNING L Outdoor Gasket Notch 2. Insert the slotted end of the square spindle (G) into the outside lever hub until it locks, at an angle of 45. (The spindle can be removed by pulling on it, if oriented incor-

rectly.) WARNING Square Spindle Position correct incorrect 3. Insert the thumbturn spindle (F) in the upper hub of the outside housing. (It will clip in place.) CAUTION IMPORTANT If installing the lock with mortise outdoors, order the proper gasket (See page 4). For doors more than 2 1/2" thick, order the appropriate hard-

ware bag to receive the correct length of spindles and mount-

ing screws. (See page 4) 4. Place the outside housing on the door so that the spindles engage the hubs on the mortise. For models 79N see appendix C Saflok RT/RT Plus Installation Guide For models 79R, 79Z, 79Y, 79Q slide the 2 spindles (F & G) onto the hub of the mortise but leave a gap between the door and the back of the lock. Connect the ajar cable from the housing

(U) to the ajar switch cable of the mortise (V). Push the lock to the face of the door ensuring that the cable connection

(U) to (V) remains in the door hole, and that the cable for the outside housing antenna (X) protrudes through the hole to the inside of the door. WARNING CAUTION Ensure no cables are pinched on assembly. 5. On the inside trim assembly turn the lever to the correct IMPORTANT horizontal rest position for the handing of the door. Install the tension spring (L) between the handle (E6) and the post (E7). E6 E7 T I I 6. Place the grommets (E14) as shown on the image of the inside trim (E). Use screws (E15) and the flat washers (E16) and fasten to the RFID module (E13) to the inside trim as-

sembly (E). CAUTION IMPORTANT WARNING Apply only for models 79Z, 79Y, 79Q. Normally assembled at the factory E13 CAUTION E16 E15 IMPORTANT E14 W For Autodeadbolt ASM, ASM Office and ASM/ESM Store-

room models, refer to Appendix A.2, A.3, A.4 at this point. 7. Put the thumbturn (T) in a vertical position. Place 3 spacers

(S) on the door (for recent models only) and place the in-

side trim assembly on the door so that the upper and lower spindles (F) and (G) engage the thumbturn and the inside lever. S S PK3720_T 06-22 11 3 Installation of Standard ASM or ESM Models

(for cylindrical see Appendix B) WARNING For models 79Z, 79Y, 79Q connect the outside housing an-

tenna cable (X) to the inside trim antenna cable (W). For the 79R model leave the outside housing antenna cable (X) in the door hole. CAUTION Ensure no cables are pinched on assembly. IMPORTANT Fasten to the outside housing using the three 1/8" hex drive mounting screws (I ). Install the screws without tightening. Verify the inside lever and thumbturn operates smoothly. If not move the inside and outside housings slightly. Then tight-

en the screws. X W S G F S I I T I C 3.5 Reversing the Outside Lever

(for series without Mechanical Override) The lever is field reversible. If the handing is incorrect, insert a small pick or flat screwdriver in the hole in the hub as shown. Gently pry back the spring clip inside the hub, and remove the handle. Access Hole 8. Assemble the lever on the outside housing, in the horizon-

tal rest position appropriate to the handing of the door. Simply push the lever onto the tube until it clicks in place. If more force is required, use a rubber mallet. Test the at-

tachment of the handle by pulling smartly on it. (For locks with mechanical override, see section 4 p.12) 9. Three AA Alkaline batteries should already be installed in the battery holder (C). Insert the battery holder into the outside housing and secure it using the 6-32 x 5/16" (7.9mm) Torx drive screw (H). WARNING CAUTION cut-away view IMPORTANT If the lock makes a continuous buzzing noise or the red LED lights continuously, reset the electronics by removing the battery holder for ten seconds then reinsert it. 12 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 4 Installation of Mechanical Override Model 4.1 Parts and Tools List Tools Required:

(L1)*

Cylinder (D1, provided with lock) or equivalent

( M1 ) Small flat scewdriver (less that 1/8")

* for recodable cylinder key #1 should be used as L1. See section 11 for more information. Diagram of lock:

Outside Lever handle Outside housing Cylinder plug Cylinder Cap

(F1)

(G1)

(H1)

(I1)

(J1) Inside drive hub Nylon washer Spring washer Drive tube Lever catch

(K1)

(O1) Override shaft Set screw cylinder plug Front Back

(A1)

(B1)

(C1)

(D1)

(E1)

(B1)

(F1)

(I1)

(J1)

(G1)

(H1) Facing view of drive tube: (E)

(I1)

(A1)

(E1)

(D1)

(O1)

(C1)

(I1)

(K1)

(J1)

(J1)

(K1) Override Shaft Saflok RT/RT Plus Installation Guide PK3720_T 06-22 13 4 Installation of Mechanical Override Model WARNING Upon unpacking, the lock housing with mechanical override should look like the diagram below with:

(N1)

(G1) The small indents on the cross of the override shaft in line horizontally The nylon washer and the spring washer on the drive tube (I1)

(J1) The lever catch in the out position

(D1) Cylinder CAUTION IMPORTANT Important: Assemble the lever, cylinder and lock components before affixing the entire unit to the door.

(N1)

(J1)

(G1)

(D1)

(L1)

(K1)

(I1) 4.2 Preparing the outside housing for the installation of the lever handle 1. Insert the cylinder (D1) to be used as a tool, or an equiva-

lent tool, to rotate the override shaft (K1) and turn it clockwise until it stops so that the two small indents (N1) on the cross are now vertically in line. (Fig.1) Fig. 1 Fig. 2 Indents (N1) In verticle position Override Shaft

(K1) 2. Push in the lever catch (J1) firmly. (see Fig. 2) to be flush with drive tube diameter

(I1)

(K1)

(J1) lever catch (J1) Push lever catch (J1) in 14 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 4 Installation of Mechanical Override Model 4.3 Preparing the lever handle and cylinder for installation 4.4 Steps to attach the lever handle to the lock housing

*NOTE: the position of the key is very important 3. Insert the cylinder (D1) without key (L1) into the lever han-

dle (A1) (see Fig.3) Fig. 3 6. Right-handed Lever handle: Turn the key (L1) aproximately 100 clockwise so that it is in the vertical position and the recess entry for key is in the top position. (See Fig. 6)

(D1) Fig. 6

(A1) Recess entry for key in the top position

(L1) Left-handed lever handle: Turn the key (L1) approximately to 100 clockwise so that it is in the vertical position and the recess entry for key is in the bottom position. (See Fig. 7) 4. Put the cylinder plug (C1) into the lever (A1) (see Fig.4) Fig. 4

(C1)

(A1) Fig. 7 WARNING CAUTION Recess entry for key in the bottom position

(L1) IMPORTANT The key (L1) and the recess entry for key must be in the positions shown in Figs 6 & 7 before placing the lever handle on the housing or the lever and the override mechanism will not work If you have assembled the lever and housing with the key

(L1) in the wrong position, the key (L1) will get stuck. To remove the key (L1), turn it so that it is in the vertical po-

sition and insert a small flat screwdriver (M1) (see page 17) into the hole under the lever handle to push Lever Catch (J1) in (Fig.2). Remove lever, remove key. If it is still stuck, turn the key 90 clockwise to the horizontal posi-

tion and push the Lever Catch (J1) in again with the small screwdriver (M1). Remove key (L1).

(L1) 5. Insert key (L1) into cylinder (D1). Hold plug (C1) in position. Troubleshooting:

(See Fig. 5). Fig. 5 WARNING CAUTION If the lever is not assembled with the key in the position shown in Fig. 6 & Fig. 7, the inside mechanism of the lock could be damaged if the lever is rotated and forced. IMPORTANT Saflok RT/RT Plus Installation Guide PK3720_T 06-22 15 4 Installation of Mechanical Override Model WARNING CAUTION 4.5 Attaching the Lever Handle to the Lock

(with the key as shown in Fig. 6 & Fig. 7) IMPORTANT 7. Fit the lever handle (A1) onto the drive tube (I1). It should rest approximately 1/16" from the body of the housing. If not, wiggle and jiggle key (L1) to align cylinder (D1) with override shaft (K1) (See Fig. 8) If the lever catch (J1) cant be pushed close to the housing, it is probably not pushed in. Push it in. (see fig 2 page 13) If it is not possible to turn the key (L1) counter-clockwise to complete this step, the spring washer (H1, see page 12) may be too tense:

Hit the lever carefully with a rubber mallet to loosen the spring washer (H1). (you may want to cover the lever handle

(A1) with a cloth or other material to protect the finish of the metal) If the lever catch (J1) is stuck, the override shaft (K1) is in the wrong position. (see fig 2 page 13) The two small indents

(N1) on the cross of the override shaft (K1) must be vertically aligned as in fig 2 page 13 Fig. 10 Fig. 8 right-handed lock 9. Remove the key (L1). The lock will look as shown in Fig.10. right-handed lock

(A1)

(L1) Recess entry for key in TOP Position

(L1) left-handed lock

(A1) Recess entry for key in BOTTOM Position left-handed lock 8. Press the lever (A1) firmly against the housing while turn-

ing the key (L1) counterclockwise (this applies to both right-handed and left-handed locks) until it is in the hori-

zontal position. (Fig. 9) Troubleshooting:

Gently check the rotation of the lever handle (A1). It should easily rotate approximately 45. Fig. 9 right-handed lock

(Housing)

(A1)

(L1) left-handed lock Right-handed Lock: Turn the lever handle (A1) clockwise without forcing it. If it stops at approximately 15, it was not assembled correctly as shown in step 6 (Fig. 6 & 7). Do not try to force it to turn. Release the lever handle (A1). Insert the small screwdriver (M1, page 16) into the small hole on the underside of the lever han-

dle (A1) and push in the lever catch (J1) see page 13. Re-do steps 2, 3, 4 & 5. Left-handed Lock: Turn the lever handle (A1) counter-

clockwise without forcing. If it stops at approximately 15, it was not assembled correctly as shown in step 6 (Fig. 6

& 7). Do not try to force it to turn. Release the lever han-

dle (A1). Insert the small screwdriver (M1, page 16) into the small hole on the underside of the lever handle (A1) and push in the lever catch (J1) see page 13. Re-do steps 2, 3, 4 & 5. 16 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 WARNING 4 Installation of Mechanical Override Model WARNING CAUTION IMPORTANT 4.6 Verify the attachment of the lever handle Very Important: To verify that the lever handle has been cor-

rectly attached to the housing:

IMPORTANT 10. Remove key (L1) 11. Insert a small flat screwdriver (tool M1, page 12) into the hole on the underside of the lever handle (A1) and push in the lever catch (J1) as per fig 11. 12. Pull on the lever handle (A1). You should not be able to remove the lever handle (A1). If it comes off of the housing, you did not assemble the lock correctly. Return to steps 2, 3, 4 & 5 and make sure that the lever (A1) looks like Fig. 10 and repeat this verification pro-

cess. (Step 10) Fig. 14

(A1) Fig. 11

(A1) washer (H1), until the handle (A1) moves freely back to its horizontal position when turned slowly. CAUTION 4.9 Test the mechanical override function This test can only be performed when the lock is not affixed to the door. 17. Without using the key (L1), turn the lever handle (A1) clockwise (for Right-handed locks) or counter-clockwise

(for Left-handed locks). The inside drive hub (F1) should not rotate when the handle (A1) turns. (Fig. 14)

(M1) Small screwdriver or equivalent tool

(F1) inside drive hub does not move 18. With the lever handle (A1) in the horizontal position, insert the key (L1) into the cylinder (D1) and turn it clockwise until it stops. (This applies to both Right and Left-handed locks, see Fig.15) 4.7 Adjust the lever feel 13. If applicable, to reduce the lever play, using the 5/64 allen key (P1), tighten the set screw (O1) while pushing the le-

ver against the front housing. Make sure the lever rotates properly after tighting the set screw (O1). See fig 12. Fig. 15 Fig. 12

(L1)

(A1) 4.8 Test the movement of the lever handle

(remove the key (L1) in cylinder (D1)) 14. Turn the handle (A1) clockwise (for a right-handed lock) or counter-clockwise (for a left-handed lock) 15. Release the handle (A1) slowly. It should return freely to its horizontal position. (Fig.13) 19. Hold the key (L1) in stopped position (should be a bit more than vertical) and turn the lever handle (A1) clockwise (for Right-handed locks) or counter-clockwise (for Left-hand-

ed locks). The inside drive hub (F1) should rotate in the same direction as the lever handle (A1) when it is turned.

(Fig. 16)

(A1) Fig. 16 Fig. 13 Cylinder

(J) 16. If the handle (A1) doesnt easily return to its original po-

sition, the spring washer (H1) (page 12) is probably too tight. Use a rubber mallet to hit the lever (A1) carefully against the housing to reduce the tension of the spring

(F1) inside drive hub rotates Saflok RT/RT Plus Installation Guide PK3720_T 06-22 17 WARNING 4 Installation of Mechanical Override Model CAUTION IMPORTANT Test the Mechanical Override Function (continued) 4.11 How to change lock cylinders Verify the functionality of the mechanical override after the lock is installed on the door: (Door must be opened) 20. With the door open, insert key (L1) in cylinder (D1) and turn it clockwise until it stops. 21. Hold the key (L1) in stopped position (should be a bit more than vertical) and turn the lever handle (A1) (clockwise for right-handed and counter-clockwise for left-handed locks). The latch must retract. 24, Fig. 18). 27. Insert key (L1). 29. Release key (L1). 25. Loosen the set screw (01) to free the lever using Allen Key

(P1) (Approx. 1/4 turn). See fig 12 page 16 26. Remove the cap (E1) from the lever handle (A1) (see step 28. Turn the key (L1) clockwise until it stops. 30. Use a small flat screwdriver to push in the lever catch (J1) through the small hole underneath the lever handle (A1)

(Fig. 19). 22. Extend deadbolt and repeat the above operation (turn key (L1) clockwise until it stops), latch and deadbolt must retract completely. Fig. 19 4.10 Cover the keyhole & cylinder with the cap 23. The cap (E1) has a small groove on one edge (to allow ease of removal) this should be facing down. Insert bot-

tom snap of cap (E1), in handle hole below the cylinder

(D1). With a small screwdriver, push the top snap of the cap down while pushing the cap (E1) into place to cover the keyhole (Fig. 17) Fig. 17

(A1) Hole below cylinder Bottom snap

(First) Top snap (Second)

(E1) Push (Third) Groove facing down 24. To remove the cap (E1), insert a small flat screwdriver into the groove and gently pry the cap off, being careful not to damage it. (You may want to cover the bottom of the lever to protect the finish from being scratched through the process of removing the cap). (Fig.18)

(A1)

(L1)

(M1) Small screwdriver or equivalent tool 31. Pull the lever handle (A1) off of the lock housing (be careful not to lose the cylinder plug (C1)). 32. Replace the old cylinder with the new one in the lever han-

dle (A1). Only the same kind of cylinder with 2 grooves in a cross in the end of the cylinder plug, could be used on the locks. (Fig. 20) Fig. 18 Fig. 20 2 Grooves in cross

(A1)

(E1)

(M1)

(D1)

(A1) 18 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 4 Installation of Mechanical Override Model WARNING CAUTION How to change lock cylinders (continued) 33. Re-insert the cylinder plug (C1) (Fig. 21) IMPORTANT Fig. 21 The Key Override itself does not retract the latch or dead-

bolt. Do not use too much force when turning the key as this may damage the unit. To retract the latch, turn the key clock-

wise until it stops, and turn the lever handle (A1). See page 15 WARNING

(C1)

(A1) WARNING CAUTION The lever handle must stay in the horizontal position when turning the key (do not try to turn the key while turning the handle) or the override mechanism will not work. CAUTION IMPORTANT IMPORTANT Always keep the door open while installing and verifying the functionality of the lock with the keycard or key override. Do not close the door until you are certain that you have in-

stalled the unit correctly. 34. While holding the cylinder (D1) and plug (C1) in place, in-

sert the key (L1) (see Fig. 22) 35. Turn the key (L1) approximately 100 clockwise 36. Repeat the steps 1 to 9 to attach the lever handle (A1) to the lock housing. (see Fig. 22) Fig. 22 Right-handed lock

(L1)

(A1) Left-handed lock Saflok RT/RT Plus Installation Guide PK3720_T 06-22 19 WARNING 4 Installation of Mechanical Override Model 4.12 The Recodable Cylinder with 3 different keys Fig. 24 Right-handed lock Read the following instructions before using any of the 3 keys supplied The recodable cylinder can be operated with three different keys. The keys are numbered 1, 2 & 3, and each key is labeled and supplied in a separate plastic bag. It is very important to use them in order. WARNING

* Always read the label instructions on the label before using The use of key #2 automatically cancels the function of key

#1, and the use of key #3 automatically cancels both keys #1 and #2. IMPORTANT If key #3 is used first, it will immediately make keys #1 and

#2 unusable. Fig. 25 Once a key is cancelled, it cant be reactivated unless the cyl-

inder itself is re-pinned. 39. Turn the key back counter-clockwise until it is in the hori-

zontal position. cylinder Left-handed lock Right-handed lock Left-handed lock CAUTION IMPORTANT a key. CAUTION Fig. 23 Key #1 Key #2

(cancels key #1) Key #3

(cancels keys

#1 and #2) How to change lock combination from key #1 to key #2:

37. Insert key #2 into cylinder. horizontal position. 38. Turn the key clockwise until it stops (see Fig. 24) for both 44. Remove the key. left-handed and right-handed locks. 40. Remove the key. Now the lock should work with key #2, and key #1 has been cancelled.

*Test: Try to use key #1 in the lock. It should no longer work. How to change lock combination from key #2 to key #3 41. Insert key #3 into cylinder. 42. Turn the key clockwise until it stops. 43. Turn the key back counter-clockwise until it is in the Now the lock should work with key #3, and key #2 has been cancelled.

*Test: Try to use key #2 in the lock. It should no longer work. 20 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX A.1 Reversing the Mortise Handing on ASM 1 1/4" Face Plate Only A.1.1 Reversible ASM 1. Place the mortise on a flat surface. 2. Partially extend the deadbolt:

For normal ASM, rotate hub (D4) using a screwdriver, until the deadbolt (D5) extends approximately 1/4". For Autodeadbolt ASM, rotate hub (D4) until the deadbolt

(D5) is fully retracted. The deadbolt will extend approx. 1/16"

from the mortise case. D4 1/16"

D5 D4 1/4"

D5 Proceed to step 3. Hold the deadbolt (D5) gently. Press and release the auxiliary latch (D6). You should feel the deadbolt trigger and begin to extend under the force of the spring. Release the deadbolt (D5) gently. It should extend to approxi-

mately 5/16" and stop. If the deadbolt extends past this point, gently press it in until it locks at a protrusion of approximately 5/16" or start step 2 again. D5 (hold gently) D6 (press and release) 5/16"

D5 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 21 APPENDIX A.1 Reversing the Mortise Handing on ASM 1 1/4" Face Plate Only A.1.1 Reversible ASM (continued) 3. Push in the latch bolt (D7) to the middle of its stroke, and hold it there. 6. Pull out the latch bolt (D7), until it just clears the front plate. (Note: If you remove the bolt completely, you must turn it 90 to re-insert it.) 1 Lock Position 2 Unlock Position D7 180 D7 D7 D7 Use a small screwdriver to lift unlock mechanism. Push in the latchbolt to the end of the stroke, and hold it there. its stroke. 7. Rotate the latch bolt (D7) 180. Re-insert it to the end of 4. Hold the latch (D7) inside the mortise, and insert the tail-

piece retaining tool (D8, part #027-510382 available sepa-

rately) so that the tailpiece (D10) will not drop inside the mortise case. Hold the tool and the latch with one hand, and slide up the tailpiece using a small screwdriver. D10 D8

(part #027-510382) D7 8. Holding the retaining tool (D8) in place, re-engage tail-

piece (D10) with the latch bolt (D7). There may be some play required to align the parts. Remove the tool (D8). D10 D7 5. Continue to hold the retaining tool (D8). Release the latch bolt (D7) and keep the anti-friction latch (D9) toward the flat side of the latch bolt so that the bolt extends fully. WARNING D8 D8 D7 D9 IMPORTANT CAUTION 9. Release the latch to the middle of the stroke and hold it there. Use a small screwdriver to push the lock mechanism back to the locked position. The lock mechanism has to be horizontal on the locked posi-

tion 22 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX A.1 WARNING Reversing the Mortise Handing on ASM 1 1/4" Face Plate Only CAUTION 10. Release the latch bolt (D7). Position the latch bolt so that the bottom tooth of the anti-friction latch (D9) remains inside the mortise case as shown. 2. If deadbolt is projected, retract the deadbolt (D5) as shown by turning the hub (D4) with a small screwdriver, then push in the latch bolt (D7) to the end of its stroke. IMPORTANT If the tooth of (D9) is outside the mortise, you will not be able to re-assemble the faceplate on the mortise. D4 D5 D7 D7 D9 D9 (tooth) mortise bottom view D7 A.1.2 Reversible ESM 1. Remove the mortise faceplate, and place the mortise on a flat surface for the following steps. LOGO 3. Release the latch bolt, and guide anti-friction latch (D9) against the flat side of the latch bolt so that it will slide out of the mortise beyond its normal throw. D9 mortise D7 bottom view D7 D9 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 23 APPENDIX A.1 Reversing the Mortise Handing on ASM 1 1/4" Face Plate Only 4. Using a small screwdriver, slide up the locking pin (D11). Pull out and remove the latch bolt (D7), rotate it 180, and reattach it. 6. Push in the latch bolt (D7) to the end of its stroke. D11 D7 D7 180 5. Re-insert the rotated latch bolt (D7) until it stops. Push down the locking pin (D11) to lock the latch bolt in the mor-

tise. D11 7. Release the latch bolt (D7) while positioning the anti-fric-

tion latch (D9) so that it will remain inside the mortise. En-

sure the bottom tooth of the anti-friction latch (D9) re-

mains inside the mortise case as shown. D9 (tooth) mortise D7 D9 bottom view D7 WARNING CAUTION IMPORTANT D7 If the bottom tooth of (D9) is outside the mortise, you will NOT be able to re-assemble the face plate on the mortise. The ESM face plate must be installed so you can read the logo. 24 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX A.2 Additional steps for Autodeadbolt ASM Do the following INSTEADOFpage 10, step 6:

5. If not already installed at the factory, put the thumbturn in the vertical position and install all four (4) parts (E) as shown, on the inside trim assembly. Place the 3 spacers (S) on the door. Place the inside trim as-

sembly on the door so that the upper and lower spindles (F) and (G) engage the thumbturn and the inside lever. Fasten to the outside housing using the three 1/8" hex head mounting screws (I). If applicable apply the privacy thumbturn sticker as shown. If in doubt as to the direction of the arrow, press the auxiliary latch (D6) to extend the deadbolt, and verify in which direc-

tion to rotate the thumbturn to reach the horizontal (priva-

cy) position. E4 E3 E17 E5 Install clip E17 diagonally on hub Turn the thumbturn all the way to the right for a RHinstal-

lation (arrow on E3 points UP), or all the way to the left for a LHinstallation (arrow on E3 points DOWN). The thumbturn should stop in the vertical position, and the stopper cam (E3) will be in the position illustrated below. RH/LHR LH/RHR S I I T S D6 I Saflok RT/RT Plus Installation Guide PK3720_T 06-22 25 APPENDIX A.3 Additional steps for ASM Office Do the following BEFORE placing the inside trim assembly on the door (page 10, step 7):

Install only parts (E4 and E5) as shown, on the inside trim assembly. Install E4 onto E5, then slide both parts onto the thumbturn. APPENDIX A.4 Additional steps for ASM/ESM Storeroom Do the following BEFORE placing the inside trim assembly on the door (page 10, step 7):

Put the thumbturn in the vertical position and install only parts (E17, E3 and E5) as shown, on the inside trim assembly. The notch on the stopper cam (E3) must engage the tab on the plate (E5), so that the thumbturn is locked in the vertical position. E5 E4 Stopper Cam E3 to be assembled in position shown. The thumbturn should be locked in the vertical position E5 Install clip E17 diagonally on hub E3 E17 E4 26 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX B Installing Cylindrical Models 23/8" &

23/4" Backset WARNING B.1 Install the Strike CAUTION Follow the same steps as for a mortise model strike (see page 8, all steps in section 3.2). Note that the handle height is aligned with the center of the strike. Strike Kit IMPORTANT For cylindrical latch models, ensure the dead-locking pin will stop against the strike when the door is closed (see figure). An incorrect installation that permits the pin to slip inside the strike may result in a total lockout and will void the warranty of the complete lock mechanism. 4 6 Correct Incorrect WARNING Install the Latch B.2 Follow the instructions on page 9, all steps in section 3.3. CAUTION Note that for cylindrical models, the axis of rotation of the handle is level with the center of the strike. Mark this height on the edge of the door in step 1 on page 8. IMPORTANT Respect applicable building codes regarding handle height. WARNING 1. Drill the hole for the latch, and chisel out clearance for the latch plate according to the template. CAUTION 2. Drill the holes for the cylindrical unit, thumbturn spindle, and lock mounting screws. Refer to template for dimen-

sions and depths. IMPORTANT Drill from both sides of the door to prevent unsightly dam-

age. WARNING 3. Install the latch (O) using 1" Phillips mounting screws. Posi-

tion the deadlocking pin (Q) opposite to the closing direc-

CAUTION tion as shown. 4. Install strike and strike dust box. IMPORTANT Use only the strike and strike box supplied. The use of non-

approved parts will result in a functionality problem and may void the warranty. 3 5 2 4 Q O Closing Direction Saflok RT/RT Plus Installation Guide PK3720_T 06-22 27 APPENDIX B Installing Cylindrical Models 23/8" &

23/4" Backset B.3 WARNING Install the Cylindrical Unit The lock is factory shipped with spacers for doors of 1 3/4"

thickness. For doors of other thicknesses remove the two screws (06 of fig. 2) and as per table 1 install the required componants (06), (07) and (08) as indicated. CAUTION Fig. 1 HANDING IMPORTANT It is very important to assemble the spacers in position shown. 1. Lock with 2 DIFFERENT SPACERS (see fig. 2) The cylindrical Unit and Attachement Plate assembly is shipped assembled in the factory for 1 3/4" door thickness (44mm) with 2 "07" spacers, 1 "08" spacer and 2 "06" 5/8" LG (see fig.4) flat head screws. Door Thickness Table 1 Door Thickness 1-3/8" (35mm) to 1-9/16" (40mm) 1-5/8" (41mm) to 1-11/16" (43mm) 1-3/4" (44mm) to 1-13/16" (46mm) 1-7/8" (48mm) to 1-15/16" (49mm) 2" (51mm) to 2-1/16" (52.5mm) 2-1/8" (54mm) to 2-3/16" (56mm) 2-1/4" (57mm) to 2-5/16" (59mm) 2-3/8" (60mm) to 2-1/2" (64mm) Fig. 3 Screw Length (Full Scale) Spacer 07 Spacer 08 2 1 2

1 2

1

1 1 2 2 2 3 3 Screw 06 3/8 (10mm) 1/2 (13mm) 5/8 (16mm) 5/8 (16mm) 3/4 (19mm) 3/4 (19mm) 7/8 (22mm) 7/8 (22mm) Fig. 2 Attachement Plate See 2 07 08 Screws 06 Cylindrical Unit Assembly Length 3/8"

Length 1/2"

Length 5/8"

Length 3/4"

Length 7/8"

28 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX B Installing Cylindrical Models 23/8" &

23/4" Backset B.3 Install the Cylindrical Unit (cont) 2. Insert the cylindrical unit from the outside of the door to-

wards the inside, so that it engages the latch as shown. This operation is to be done at B.5 step 4.

(outside) Put the thumbturn in the vertical position so that the arrow on the disc (E11) points UP. If installing as a Storeroom function lock, lift the plate (E12) until the hole in the plate is aligned with the hole in the disc

(E11), and fasten the disc and the plate securely together with the screw (E10) and lock washer (E9) provided. The screw head MUSTtouch the surface of the disc for correct assembly. cylindrical unit latch E11 E9 E10 V E11 E12 B.4 Inside Trim Assembly for Cylindrical The inside trim assembly for cylindrical models includes parts assembled at the factory to control the motion of the thumb-

turn. An additional spring (E8) and locking screw (E10), packed separately, is added for storeroom applications (no privacy). Do the following BEFORE placing the inside trim assembly on the door (page 10, step 7):

Install the additional tension spring (E8) between the plate

(E12) and the post (E7), on the side opposite the lever handle spring installed in the last step. E12 E8 E7 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 29 APPENDIX B Installing Cylindrical Models 23/8" &

23/4" Backset B.5 Install Outside Housing and Trim Assembly for Cylindrical 4. Place the outside housing on the door so that spindle (F) engages the thumbturn hole and spindle (G). 1. Insert the slotted end of the square spindle (G) into the outside lever hub until it locks, at an angle of 45. (The spindle can be removed by pulling on it, if oriented incor-

rectly.) For models 79Z, 79Y, 79Q connect the cable (X) to the cable

(W - not shown). For model 79R leave the cable (X) in the door. Make sure both cables are not pinched between the inside trim and outside lock on the face of the door. Engage hub of cylindrical unit. The cylindrical unit will engage the latch as shown in step 2 of B.3 (page 29). Square Spindle Position correct incorrect 2. Insert the thumbturn spindle (F) in the upper hub of the outside housing. (It will clip in place.) 3. Assemble the gasket onto the outside housing. Assemble the cylindrical plate assembly onto the outside housing. Y- Cylindrical Plate Assembly F X N - Gasket B1 - Lock Housing G 30 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 APPENDIX B Installing Cylindrical Models 23/8" &

23/4" Backset 5. Put the thumbturn (T) in a vertical position. Assemble the 3 spacers (S) on the door (for recent models only). Place the inside trim assembly on the door so that the upper and lower spindles (F) and (G) engage the thumbturn and the inside lever. Fasten to the outside housing using the three 1/8" hex drive mounting screws (I). Install the screws with-

out tightening. Verify that the inside lever and thumbturn operates smoothly. If not, move the inside and outside housings slightly, then tighten the screws. S W I I X S S C WARNING T CAUTION 7. Testing the cylindrical lock: Follow all steps of page 16 but extension and retraction will be for latch only. I IMPORTANT If the lock makes a continuous buzzing noise or the red LED lights continuously, reset the electronics by removing the bat-

tery holder for ten seconds, then reinsert it. 6. Three AA Alkaline batteries should already be installed in the battery holder (C). Insert the battery holder into the outside housing and secure it using the 6-32 x 5/16" (7.9mm) Torx drive screw (H). Saflok RT/RT Plus Installation Guide PK3720_T 06-22 31 APPENDIX C Escape Return Model (79N) C.1 ASM, ESM & ADB Inside trim assembly for 79N. Note: 79N models are only for sale in Europe, where building codes allow. Use with mortise only. Note: The inside trim assembly (E) for ASM/ESM and ADB on 79N models includes the part (E3) as shown below. The position of the stopper (E3) is very important. E3 E3 E6 E7 Autodeadbolt Right Hand Autodeadbolt Left Hand ASM Right &

Left Hand C.2 Installation of extension spring on inside trim. 1. On the inside trim assembly turn the lever to the correct horizontal rest position for the handing of the door. install the extension spring (L) between the handle (E6) and post

(E7). 2. Install the additional tension spring (E8) between the plate

(E12) and the post (E7), on the side opposite the lever han-

dle spring installed in the last step. L E12 E8 E7 32 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 Installation Guide Lexicon Letters for E MODEL Letters for inside trim Stopper Spring turn knob Turn knob plate Inside trim lever handle plate Inside plate tab to hook spring Pusher return spring Washer 6 star Screw 6-32 Plate turn knob ( disc ) Pusher assy ( plate ) RFID Module Cable grommet Machine Screw # 6 x 5/16 Flat washer # 6 Retaining clip Letters for mortise component Screw mortise Lock washer Dead bolt hub Dead bolt Auxiliary bolt Latch bolt Reversible tool Anti friction latch Latch bolt pusher ESM reversible pin Face Plate screw E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 E16 E17 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 Outside lever E Outside housing Battery assembly Mortise assembly Inside trim assembly Turn knob spindle Square spindle Torx head screw 3 Mounting screws Machine screw 12-24x1/2 or 2 wood screws Strike kit Extension spring Part required to control thumbturn motion Outdoor gasket Cylindrical latch and hardware Face plate Latch deadlocking pin Mortise 2 screws for bevel 3 Spacers Turn knob inside trim Cable ajar outside housing Cable mortise ajar switch Cable antenna inside trim Cable antenna outside housing Cylindrical plate assembly Letters for K MODEL Outside lever K Outside housing K Cylinder plug Cylinder Cylinder cap Instruction sheet attach lever on lock Inside drive hub Nylon washer Spring washer Drive tube Lever catch Override shaft Key Small flat screwdriver Small indent cross override shaft Set screw cylinder plug Allen Key 5/64"

A B C D E F G H I J K L M N O P Q R S T U V W X Y A1 B1 C1 D1 E1 E2 F1 G1 H1 I1 J1 K1 L1 M1 N1 O1 P1 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 33 Note for RT Plus series customers:

ISED non-interference disclaimer FCC Compliance Statement For class B contains transmitter(s)/

This device receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

license-exempt 1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, conomique Canada Sciences applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

et Dveloppement 1) Lappareil ne doit pas produire de brouillage;

2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure statement This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.6 inches) between the radiator and any part of your body. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformit ISED RSS-102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres. in accordance with the This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance. 34 Saflok RT/RT Plus Installation Guide PK3720_T 06-22 dormakaba USA Inc. Customer services & support 1.800.999.6213 / + 1.248.837.3700 General information:

dormakaba.us Online consumable orders:

www.saflokstore.com To access all of our easy steps, please visit our support website:

www.dormakabalodgingsupport.com e c i t o n t u o h t i w e g n a h c o t t c e b u S j 2 2

6 0 0 2 7 3 K P www.dormakaba.com

Q8SRTPLUS Label to be placed in the outside housing of the lock. See picture below. COMPANY NAME: dormakaba Canada Inc. Product: 79RT Plus Series Model: RT Plus IC: 4652A-RTPLUS FCC ID: Q8SRTPLUS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Made in Canada

June 10, 2022 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: Q8SRTPLUS Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below:

PERMANENT LONG-TERM CONFIDENTIALITY:

SHORT TERM CONFIDENTIALITY FOR A PERIOD OF 30 DAYS:

Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation Internal Photos External Photos User Manual Test Set-up Photographs When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed:

Printed name: James Mills Title: Vice President LGS & Product Development ACS dormakaba Canada Inc. | 7301 Decarie blvd, H4P 2G7, Montreal, QC l T: +1 514 735 5410 l www.dormakaba.com