Switch Reader Add-On Installation Instructions TOOLS NEEDED Drill Drill Bits Screwdrivers Center Punch 0.366 (Letter U) 0.136 (#29) Safety Glasses
#2 Phillips Tape Measure Tamper Proof Torx T8 1/64 Slotted OV E RV I E W Features Operating temperature range:
-35C to +66C or -31F to +151F IP Rated: IP56 NOTE: Available wire lengths to connect to provided 18" harness:
011-518290: 10" (sold separately) 011-518290: 25" (sold separately) 011-518290: 50" (sold separately) A A B E F(2x) B C D Cover-Control Circuit Board and Harness Assembly Mounting Plate C Gasket D Main Control Circuit Board C E F(2x) Flat Head Undercut Tamper Proof Screw Torx Drive T8: 4-40 1/4"
Self-Tapping Screw Pan Head Stainless Steel Phillips Drive #2: 8-32 1/2"
1/8 T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s CONSIDER MOUNTING PLACEMENT. 1 2 PREPARE SURFACE. NOTE: The placement of the Switch Reader Add-On will vary from application to application based on the environment and aesthetic preference. NOTE: For the provided mounting screws F(2x), adjust as needed depending on the surface and the hardware. Consider the mounting placement of the Switch Reader Add-On by placing the reader beside, above or below the existing reader. Switch Reader Add-On Existing reader Door frame 1 Place beside the existing reader. Switch Reader Add-On Existing reader Door frame Door frame Existing reader Switch Reader Add-On 2 Place above or below the existing reader. 2/8 NOTE: The provided mounting screws F(2x) will not cover all installation scenarios due to certain surface compositions such as brick, drywall, or other materials. Ensure that the correct drill bits, mounting screws and screw anchors are purchased and used to meet the needs of each individual application. WARNING:
Take proper precautions when installing the Switch Reader Add-On . Mounting Plate (B) Hole Locations a b c
.366"
[ 9.3mm]
.136"
[ 3.45mm]
Not to scale 1:1. 1"
[25.4mm]
NOTE: Mounting plate (B) may be used as a drilling template. 1 Prepare the surface by ensuring the surface is clean and smooth. 3 Use a center punch tool to mark holes a, b, and c. 2 Using the mounting plate (B) as a 4 Drill holes. template, place and correctly orient the mounting plate (B) onto the surface. T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s 2 PREPARE SURFACE. NOTE: For the provided mounting screws F(2x), adjust as needed depending on the surface and the hardware. NOTE: The provided mounting screws F(2x) will not cover all installation scenarios due to certain surface compositions such as brick, drywall, or other materials. Ensure that the correct drill bits, mounting screws and screw anchors are purchased and used to meet the needs of each individual application. WARNING:
Take proper precautions when installing the Switch Reader Add-On . Mounting Plate (B) Hole Locations a b c
.366"
[ 9.3mm]
.136"
[ 3.45mm]
Not to scale 1:1. 1"
[25.4mm]
NOTE: Mounting plate (B) may be used as a drilling template. 1 Prepare the surface by ensuring the surface is clean and smooth. 3 Use a center punch tool to mark holes a, b, and c. 2 Using the mounting plate (B) as a 4 Drill holes. template, place and correctly orient the mounting plate (B) onto the surface. 3/8 T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s 3 FASTEN MOUNTING PLATE AND GASKET TO SURFACE. 4 RUN HARNESS THROUGH MOUNTING PLATE AND GASKET. REMINDER: Install the mounting plate
(B) to a clean and smooth surface using appropriate hardware. NOTE: Carefully thread the harness through the mounting plate (B), gasket
(C) and into the wall cavity to avoid damaging other components housed in the wall. Harness 7 CONNECT READER/HARNESS ASSEMBLY TO MAIN CONTROL CIRCUIT BOARD. NOTE: The main control circuit board should not be placed where it will be exposed to external environmental conditions such as water, rain or extreme temperature. 5 V G N D D + D -
F(2x) C B A C B 5 INTERLOCK COVER HOOK WITH MOUNTING PLATE TAB. 6 SECURE COVER WITH TAMPER PROOF SCREW. Mounting plate tab Cover hook A B A E 4/8 A 21 3 4 D SWITCH READER ADD-ON TO MAIN CONTROL CIRCUIT BOARD ID Position Wire Color 5V 1 RED GND 2 D+
3 D-
4 BLACK WHITE GREEN T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s 7 CONNECT READER/HARNESS ASSEMBLY TO MAIN CONTROL CIRCUIT BOARD. NOTE: The main control circuit board should not be placed where it will be exposed to external environmental conditions such as water, rain or extreme temperature. 5 V G N D D + D -
A 21 3 4 D SWITCH READER ADD-ON TO MAIN CONTROL CIRCUIT BOARD ID Position Wire Color 5V 1 RED GND 2 D+
3 D-
4 BLACK WHITE GREEN 5/8 T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. Sw i tc h Rea d e r Ad d - O n I n sta l l at i o n I n st r u ct i o n s FC C / I C C e r t i cat i o n 8 CUT EXISTING ACCESS CONTROL WIRE AND RECONNECT TO SWITCH READER ADD-ON MAIN CONTROL CIRCUIT BOARD. NOTE: The existing building site's reader, access control wiring and panel placement will vary in each installation. From access control reader V+
GND D0 D1 RED GRN HLD BUZ TAM DW To existing reader received, including interference that may cause undesired operation. Changes or modications to this equipment not expressly approved by the party responsible for compliance (Hardware Manufacturer: dormakaba) could void the users authority to operate the Switch Reader Add-On Main Control Circuit Board V+
GND D0 D1 RED GRN HLD BUZ TAM DW COMPLETE 6/8 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC there is no guarantee that interference will not Operation is subject to the following two conditions:
does cause harmful interference to radio or
( 1 ) This device may not cause harmful interference, turning the equipment off and on, the user is interference to radio communications. However, occur in a particular installation. If this equipment television reception, which can be determined by encouraged to try to correct the interference by
(2) This device must accept any interference one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. technician for help. Consult the dealer or an experienced radio/TV Statement RULES. and equipment. WEEE This symbol means that you must dispose of an electrical item AND/OR containing in it Li-Mn battery separately from general household waste when they reach the end of their useful life. Take your PC or the battery to your local waste collection point or center. This applies to all countries of the European Union, and to other countries with a separate waste collection system. Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Statement conditions:
and THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS STANDARD(S). Operation is subject to the following two
(1) This device may not cause interference,
(2) This device must accept any interference, including any interference that may cause undesired operation of the device. This Class [B] digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations. CET APPAREIL EST CONFORME LA NORME RSS INDUSTRIE CANADA EXEMPT DE LICENCE. Son fonctionnement est soumis aux deux conditions suivantes:
T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. FC C / I C C e r t i cat i o n Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions:
( 1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modications to this equipment not expressly approved by the party responsible for compliance (Hardware Manufacturer: dormakaba) could void the users authority to operate the equipment. WEEE interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Statement THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS STANDARD(S). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including any interference that may cause undesired operation of the device. This Class [B] digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations. CET APPAREIL EST CONFORME LA NORME RSS INDUSTRIE CANADA EXEMPT DE LICENCE. Son fonctionnement est soumis aux deux conditions suivantes:
This symbol means that you must dispose of an electrical item AND/OR containing in it Li-Mn battery separately from general household waste when they reach the end of their useful life. Take your PC or the battery to your local waste collection point or center. This applies to all countries of the European Union, and to other countries with a separate waste collection system. Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 7/8 T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved. interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. technician for help. Consult the dealer or an experienced radio/TV Statement conditions:
and THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS STANDARD(S). Operation is subject to the following two
(1) This device may not cause interference,
(2) This device must accept any interference, including any interference that may cause undesired operation of the device. This Class [B] digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations. CET APPAREIL EST CONFORME LA NORME RSS INDUSTRIE CANADA EXEMPT DE LICENCE. Son fonctionnement est soumis aux deux conditions suivantes:
FC C / I C C e r t i cat i o n
(1) Cet appareil ne doit pas provoquer dinterfrences, et
(2) Cet appareil doit accepter toute interfrence, y compris les interferences pouvant causer un mauvais fonctionnement du dispositif. Cet appareil numrique de la classe [B] respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. WARNING: Changes or modications not expressly approved by dormakaba could void the users authority to operate the equipment. For Online Instructions Visit:
https://dhwsupport.dormakaba.com/hc/en-us For Assistance or Warranty Information:
Call 1-800-392-5209 or visit https://dhwsupport.dormakaba.com/hc/en-us Para obtener instrucciones lnea, visite:
https://dhwsupport.dormakaba.com/hc/en-us Si desea ayuda o informacin sobre la garantia:
llame al 1-800-392-5209 ou visite https://dhwsupport.dormakaba.com/hc/en-us English El idioma espaol Pour obtenir des directives en ligne, consultez le site :
https://dhwsupport.dormakaba.com/hc/en-us Pour de l'aide ou des informations sur la garantie:
Vauillez appeler le 1-800-392-5209 ou visiter El idioma francs 8/8 T92381_ABEST is a trademark of dormakaba USA Inc. 2021 All rights reserved.