PhoneEasy 410gsm English 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Side key (volume) Display Left soft key Call key Numeric keypad
# / Change profile End call/Power on/off Arrow keys Right soft key 11. 12. 13. 14. 15. 16. 17. 18. 19. Charging contacts, for use with charging stand (not included) Emergency call key Battery cover Headset socket Charging socket Loudspeaker Microphone Led light (Battery level low) Led light (New message) Disclaimer and limitation of liability Doro AB and its affiliates, licensees and retailers assume no responsibility for any damage or loss resulting from the use of this guide. Doro AB and its affiliates, licensees and retailers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. Doro AB and its affiliates, licensees and retailers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of all important data on other media to protect against data loss. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL DORO AB OR ANY OF ITS AFFILIATES, LICENSEES AND RETAILERS BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED AS IS. EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY, OR CONTENTS OF THIS DOCUMENT. DORO AB RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE. FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Doro has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the equipment. 2009 Doro AB. All rights reserved. English Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing the SIM card and battery . 3 Charging . 4 Phone indicators . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Activating the phone . 5 Making a call . 6 Making a call from the Phonebook . 6 Receiving a call . 6 Volume control . 6 Display symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Call options . 8 Call waiting . 9 Call information . 9 Call log . 9 Phonebook . 10 Silent mode . 12 Headset . 12 SOS calls . 13 Emergency Call key . 13 Alarm . 14 Games . 14 Calendar . 15 Calculator . 15 FM radio . 16 Text input . 18 SMS messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Creating and sending SMS . 19 Incoming SMS (Inbox) . 19 Outgoing SMS (Outbox) . 20 1 English MMS messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Creating and sending MMS . 22 Outgoing MMS (Outbox) . 24 Incoming MMS (Inbox) . 24 Managing files and folders . . . . . . . . . . . . . . . . . . . . . . . . . 26 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Time and date . 27 User setup . 28 Tone settings (rings & tones) . 29 Bluetooth settings . 31 Blocking functions . 32 Emergency . 32 Voice mail . 34 Speed dial . 35 Call setup . 35 Messages . 37 Network setup . 39 Services . 40 Security settings . 40 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Warranty and technical data . . . . . . . . . . . . . . . . . . . . . . . 47 2 English Installation Warning!
Turn off the phone and disconnect the charger before removing the battery cover . Installing the SIM card and battery The SIM card holder is located behind the battery. 1 . Remove the battery cover by pressing it carefully down and sliding away from the emergency call key. Remove the battery if it is already installed. Press lightly on the cardholder and carefully slide it towards the emergency call key. The SIM card holder can now be folded into an upright position. Placing the SIM-card on the marked area of the compartment. Make sure that the SIM cards contacts are facing downwards and that the cut-off corner is placed accordingly with the marked area. See picture. Take care not to scratch or bend the contacts on the SIM card. Fold the SIM-card holder down and carefully slid it away from the emergency call key until it clicks into place. Insert the battery by sliding it into the battery compartment with the contacts facing towards the emergency call key. Replace the battery cover until it clicks into place. 2 . 3 . 4 . 5 . 6 . 7 . 8 . 3 Charging English Warning!
Only use batteries, charger and accessories that have been approved for use with this particular model . Connecting other accessories may be dangerous and may invalidate the phones type approval and guarantee . When the battery is running low, is displayed and a warning signal is heard. To charge the battery, connect the mains adapter to the wall socket and to the charging socket y. is displayed briefly when the charger is connected to the when it is disconnected. phone, and The battery charge indicator will be animated while charging. It takes approximately 3 hours to fully charge the battery. is displayed when charging is completed. Note!
Full battery capacity will not be reached until the battery has been charged 34 times. The ambient temperature must be in the range 32104F when charging. Batteries degrade over time, which means that call time and standby time will normally decrease with regular use. Phone indicators When 5 flash you have a new message or a missed call. When ] flash the battery is running low. 4 English Operation Activating the phone Press and hold the red button The following messages may be displayed:
on the phone to turn it on/off. SIM card missing or incorrectly inserted. SIM card damaged or not valid. If the SIM card is valid but protected with a PIN code (Personal Identification Number), PIN: is displayed. Enter the PIN code and press OK. Delete with Clear. Note!
If PIN and PUK codes were not provided with your SIM card, please contact your network operator. Trials: # shows the number of PIN attempts left. When no more attempts remain, SIM blocked is displayed. The SIM card must now be unlocked with the PUK code (Personal Unblocking Key). 1. Enter the PUK code and confirm with OK. 2. Enter a new PIN code and confirm with OK. Changing the language, time and date On first use, the phone language, time and date must be set. The default language is determined by the SIM card. See Settings on how to change language, time and date. If the operator supports automatic time/date setting, you might get a question upon installation if you want to update to the suggested time. Press Yes to accept or No to reject the suggested time. 5 English Making a call 1 . 2 . 3 . Enter the phone number. Delete with Clear. Press q to dial. Press Abort to cancel dialing. Press L to end the call. Note!
When making international calls, press * twice for the international prefix "+". lwa e + eore the contr lwa e + eore the contr code (instead of 00 or similar) for best operation. Making a call from the Phonebook 1 . Press Name to open the phonebook. 2 . Use the arrow keys phonebook, or quick search by pressing the key corresponding to the first letter of the entry, see Text inpt. Press Call to dial the selected entry, or press Back to return to standby mode. to scroll through the 3 .
Receiving a call 1 . Press q to answer, or press Silent to switch off the ring signal and then Reject to reject the call (busy signal). Alternatively, press L to reject the call directly. Press L to end the call. 2 . See also Call options. Volume control Use the side keys +/ to adjust the sound volume during a call. The volume level is indicated on the display. 6 English Display symbols Signal strength Ring only Ring + vibration Vibration only Alarm active Headset connected Bluetooth on Bluetooth connected Battery level New SMS Roaming (in other network) New MMS Silent SIM card missing Charger connected SIM card error Charger disconnected Mute New MMS message New SMS message SOS calls only OK (confirmed) Query Headset connected Headset disconnected Handsfree on Handsfree off Warning Error Battery level low Charging (animated) Calling Incoming call Searching Call ended Missed call Call on-hold Progressing (animated) Incoming picture 7 English Additional functions Call options During a call the soft keys1 give access to additional functions:
Options (left soft key) A menu with the following options is displayed:
Hold single call End single call New call Phonebook Msg centre Mute Hold the current call End the current call (same as L) Call another number (three-party call) Search the phonebook Write or read SMS messages. And access File manager Disable the microphone (mute) SPK on (right soft key) Activates handsfree mode, which allows you to speak without holding the phone. Speak clearly into the microphone at a maximum distance of 1 meter (3 feet). Use the side keys +/ to adjust the loudspeaker volume. Press SPK off to return to normal mode. Note!
The handsfree function allows only one person at a time to talk. Switching between talk/listen is triggered by the sound of the person talking. Loud noises (music, etc.) in the background may interfere with the handsfree function. 1 Soft keys have multiple functions. The current key function is shown above the soft key on the display. 8 English Call waiting An alert tone will be heard if there is an incoming call while talking. To put the current call on hold and answer the incoming call, press Options. This service must be activated, see Settings/Call setup. Call information During a call, the called or calling phone number and the elapsed call time is displayed. If the identity of the caller is withheld, Unknown is displayed. Call log Answered, missed, and outgoing calls are saved in a combined call log. 20 calls of each type can be stored in the log. For multiple calls related to the same number, only the most recent call is saved. Retrieving and dialing 1 . Press q. Alternatively press Use the arrow keys 2 . press Menu, scroll to and press OK.
to scroll through the call list.
= Incoming call
= Outgoing call
= Missed call 3 . Press q to dial the number or press Options for the following settings:
View Delete Delete all Save Show details for the selected call Delete the call Delete all calls in the call log Save the number in the Phonebook 9 English Phonebook The phonebook can store 100 entries with 3 phone numbers in each entry. and press OK. Creating a phonebook entry 1 . Press Menu, scroll to 2 . Select -New contact- and press Add. 3 . Enter a name for the contact, see Text inpt. Delete with Clear. 4 . Use to select Mobile, Home number or Office number, and enter the phone number(s), then press Save. Press L (repeatedly) to return to standby mode.
5 . Note!
For international phone nmer, alwa e + eore the country code (instead of 00 or similar) for best operation. Press Menu, scroll to Select an entry and press Options. Select one of the following options and press OK. Managing phonebook entries 1 . 2 . 3 . View Show details for the selected call. and press OK. to move the cursor. Delete with Clear.
Use Press Save. Edit 1 . 2 . Add new See Creating a phonebook entry. Call Press OK to call the contact. Send SMS Press OK to write a SMS message, see SMS messaging. 10 English Send MMS Press OK to write a MMS message, see MMS messaging. Top 10 setting Press OK then Add to set the entry as one of the first 10 numbers in the phonebook. To delete a Top 10 entry, select the entry in the Top 10 list and press Options, then Delete. Delete Press OK to delete the selected phonebook entry. Press Yes to confirm or No to abort. Delete all Select From SIM or From Phone and press OK to delete all phonebook entries from the SIM card or phone memory. Enter the SIM-/phone code and press OK to confirm. Copy all Select From SIM and press OK to copy all phonebook entries from the SIM card to the phone memory. Press Yes to confirm or No to abort. Select From Phone and press OK to copy all phonebook entries from the phone memory to the SIM card. Press Yes to confirm or No to abort. Storage Select SIM or Phone and press OK to select the default storage for new phonebook entries. 11 English Send vCard Select Send by SMS and press OK to send the selected phonebook entry as a vCard via SMS. Enter the phone number of the recipient (or press Search) and press OK to send. Select Send Bluetooth and press OK to send the selected phonebook entry as a vCard via Bluetooth. See Settings/Bluetooth on how to connect with Bluetooth. Silent mode Silent mode is a fixed profile with SMS and ring signals disabled, while vibration and key tone settings are unchanged. Press and hold # to activate/deactivate Silent mode. See also Settings. Headset When a headset is connected, the internal microphone in the phone is automatically disconnected. When receiving a call you can use the answer key on the headset cable to answer and end calls. Warning!
Using a headset at high volume can damage your hearing . Adjust the sound volume carefully when using a headset . 12 English SOS calls When the phone is turned on, the right soft key shows SOS before the SIM card is activated or if the phone lock is on. Press SOS and then press Yes to automatically call 112. Press No to return to the activation screen. If you pressed Yes by mistake, press Abort immediately to abort. As long as the phone is switched on, it is always possible to place an emergency call by entering 112 followed by q. Most but not all networks accept calls to 112 or 911 without a valid SIM card. Contact your network operator for more information. Emergency Call key To make an emergency call, press and hold the Emergency Call key on the back of the phone for 3 seconds, or press it two times within 1 second. The phone will send an emergency SMS text message to all phone numbers in the Emergency numbers list. The phone will then dial the first number on the list. If the call is not answered within 30 seconds, the next number is dialed. Dialing is repeated 3 times or until the call is answered, or until L is pressed. The Emergency Call function must be activated before use. See Settings on how to activate this function as described above or with 3 key presses, how to enter Emergency Numbers, and how to edit the emergency SMS message. Note!
tomatic call to 112 are normall not allowed. Do not ave this number in the list of numbers to be called automatically. Some private security companies can accept automatic calls rom their client. lwa contact the ecrit compan eore programming in its number. 13 English Alarm 1 . 2 . 3 . 4 . 5 . 6 . 7 . and press OK. Press Menu, scroll to Select On and press OK. Enter the alarm time using the keypad, then press OK. For a single occurrence, select Single and press Save. For a repeated alarm, select Repeated and press OK. Scroll through the list of weekdays and press On/Off to enable/disable the alarm for each weekday, then press Save. To edit an alarm, press Edit, then press OK. To stop the alarm, press Off. The alarm is now deleted. Note!
The alarm function will work even when the phone is switched off. When the alarm goes off a signal will sound. Press Stop to turn off the alarm or press Snooze to repeat the alarm after 9 minutes. Games 1 . 2 . Press Menu, scroll to Select a game (e.g. Robot) then press OK for the following settings:
and press OK. Start game Game level Best grades Help Press OK to start a new game. Select difficulty level and press OK. Shows your best results. Press Back to return to the menu or Reset to reset the scores. Shows instructions for the game. Press Back to return to the menu. 14 Calendar English and press OK. Press Menu, scroll to Select Options. Select one of the following options and press OK. 1 . 2 . 3 . View tasks Show tasks for the selected date. Add task 1 . 2 . 3 . Enter a date for the task, then press Enter a time for the task, then press Press Edit, enter a description for the task (see Text inpt), then press Done. Press Save to save the task. 4 . At the recorded date/time, an alert tone will be played and the task description will be shown on the display. Jump to date Enter the date and press OK. Note!
The tasks function will work even when the phone is switched off. Calculator The Calculator can perform basic math operations. 1 . 2 . 3 . 4 . 5 . and press OK. Press Menu, scroll to Enter the first number. Use # to enter decimal points. Use the arrow keys to select an operation (+, -, x, ) and press OK. Enter the next number and press OK. Repeat steps 24 as necessary. Select = and press OK to calculate the result. 15 English FM radio The FM radio has a frequency range from 87.5 to 108.0 MHz and 9 preset channels. Note!
The FM Radio and its settings are only available when a headset is connected. The headset also works as a radio antenna. Turning the radio on 1 . Connect the headset to the headset socket
. 2 . 3 . and press OK. Press Menu, scroll to The radio is now turned on. The currently tuned frequency is displayed. Use the side keys +/ to adjust the volume. Press L to return to standby mode. The radio will continue to play. Selecting channels Press keys 1 9 to quick-select a preset channel while the radio is playing. or and press OK. Setting channels manually 1 . Press Menu, scroll to 2 . Select channel using 3 . When a station has been found, select Options. 4 . Select Save frequency and press OK. 5 . Enter a name for the new channel (See Text inpt). 6 . Press Save. Turning the radio off 1 . 2 . Press Menu, scroll to and press OK. Press Options, and then press Switch off. Disconnecting the headset will also turn off the radio. 16 English and press OK. Editing the channel list 1 . 2 . 3 . 4 . 5 . Play Press Menu, scroll to Select Options. Select Channel list and press OK. Select the channel you wish to edit and press Options. Select one of the following options and press OK. Delete Edit Play the selected channel. Delete the channel. Press Yes to confirm or No to return to the channel list. Press Edit to edit the channel name, then press Done. to edit the frequency, use # to enter the Press decimal point. Press Save. Changing search mode 1 . 2 . 3 . 4 . Fine tune and press OK. Press Menu, scroll to Select Options. Select Manual input and press OK. Select one of the following options and press OK. Manual tuning with or Auto search Automatic station search with or Saving channels automatically 1 . 2 . 3 . Press Menu, scroll to Select Options. Select Auto save and press OK to automatically install available radio stations in channels 1-9. and press OK. Note!
This will overwrite all previously saved channels!
17 English Text input Text is entered by pressing the numerical keys repeatedly to select characters. When writing SMS/MMS messages in some languages you can use the Smart ABC (eZiType) input method which uses a dictionary to suggest words. See Settings on how to change input method.
to move the cursor within Entering text Press the key repeatedly until the desired character is shown. Wait a few seconds before entering the next character. Press * for a list of special characters. Select the desired character and press OK to enter it. Use the side keys +/ or the text. Press # to cycle upper case, lower case and numerals. Entering text with Smart ABC Press each key once, even if the displayed character is not the one you want. The dictionary will suggest words based on the keys you have pressed. Use the arrow keys to select a word, then press OK and continue with the next word. If none of the suggested words are correct, press # to change to manual input mode. The icon on the top left of the display indicates the input mode:
eZi ABC eZi abc ABC abc 123 UPPER CASE with SmartABC lower case with SmartABC UPPER CASE lower case Numerals 18 English SMS messaging and press OK. Creating and sending SMS 1 . 2 . 3 . 4 . 5 . Press Menu, scroll to Select SMS and press OK. Select Write message and press OK. Type your message (see Text inpt) then press Done. Select one of the sending options below and press OK to confirm. Send only Save and send Send to many Send the message without saving Send the message and save it in the Outbox Add more recipients for the message If Send to many was selected, do the following:
1 . 2 . 3 . Select Recipients and press OK. Select one of the empty entries and press Edit. Enter a phone number or press Search to open the phonebook. After entering or selecting a number, press OK. Repeat step 23 to add additional recipients. When finished, press Done. 4 . Note!
For international phone nmer, alwa e + eore the country code (instead of 00 or similar) for best operation. and press OK. Incoming SMS (Inbox) 1 . Press Menu, scroll to 2 . Select SMS and press OK. 3 . Select Inbox and press OK. 4 . Select a message from the list and press Read. Use Press Options, seesee Otgoing SMS (Otox). to scroll the message up/down. 5 .
19
to scroll the English Outgoing SMS (Outbox) 1 . 2 . 3 . 4 . Press Menu, scroll to Select SMS and press OK. Select Outbox and press OK. Select a message and press OK. UseUse message up/down. Press Options. and press OK. 5 . Send (Outbox) Select one of the sending options and press OK to confirm, (see(see Creating and sending SMS). Reply (Inbox) Type your reply, then press Done. The message will be sent immediately. Call Press OK to call the contact. Delete Press Yes to delete the message, or No to return to the menu. Edit Edit the message, then press Done to show the sending options
(see Creating and sending SMS). Forward (Inbox)
(Inbox) Forward a message from your Inbox/Outbox. Press Done to show the sending options. Delete all Press Yes to delete all messages in the Inbox. Press No to return to the menu. 20 English Use number Displays all phone numbers contained in the message as well as the number of the sender. 1 . 2 . 3 . Call Save Send SMS Use the arrow keys to select one of the displayed numbers. Press Options. Select one of the following options and press OK. Call the selected number Save the number in the phonebook Write a new SMS message 21 English MMS messaging and press OK. Press Menu, scroll to Select MMS and press OK. Select Write message and press OK. Add recipients, subject and content, then press Done. Creating and sending MMS 1 . 2 . 3 . 4 . To add recipients (To), do the following:
1 . 2 . Select To and press Edit. Enter a phone number or press Search to open the phonebook. After entering or selecting a number, press OK. Press Options and repeat step 2 to add additional recipients. When finished, press Done. 3 . Note!
For international phone nmer, alwa e + eore the country code (instead of 00 or similar) for best operation. To add a Subject, do the following:
1 . Select Subject and press Edit. 2 . Type your subject (see Text inpt), then press Done. To type a message and Edit content, do the following:
1 . 2 . Select Edit and press Edit. Type your message (see Text input), then press Options to add/edit/remove attachments. 22 English Note!
Onl file alread received and aved can e attached to a message. The phone has no photographing or recording functions. Select Edit and press OK. Select an image, then press OK. Press Done to confirm. Select Add picture and press OK. Select an image, then press OK. Press Done to confirm. Add image 1 . 2 . 3 . Edit image 1 . 2 . 3 . Delete image 1 . 2 . 3 . Send MMS To send your message, do the following. 1 . 2 . Select Delete and press OK. Select an image and press OK. Press Done to confirm. Press Done. Select one of the sending options below and press OK to confirm. Send only Save and send Exit Send the message without saving Send the message and save it in the Outbox Exit without saving or sending 23 and press OK. Press Menu, scroll to Select MMS and press OK. Select Outbox and press OK. Select a message and press Options, see Incoming MMS (Inox). English Outgoing MMS (Outbox) 1 . 2 . 3 . 4 . Incoming MMS (Inbox) 1 . 2 . 3 . 4 . and press OK. Press Menu, scroll to Select MMS and press OK. Select Inbox and press OK. Select a message from the list and press Options. Use the arrow keys to scroll the message up/down. View Press Options and then Play to view the message, or Save to save the image. Press OK to confirm. Reply (Inbox) Type your reply in Edit content, then press Done and select one of the sending options (see Creating and sending MMS). Reply by SMS (Inbox) Type your reply, then press Done. The message will be sent immediately. Reply all (Inbox) Type your reply in Edit content, then press Done and select one of the sending options (see Creating and sending MMS). Forward Add recipients (To), then press Done and select one of the sending options (see Creating and sending MMS). Edit (Outbox) To edit recipients, image and content, (see Creating and sending MMS). 24 English Delete Press Yes to delete the message, or No to return to the menu. Delete all Press Yes to delete all messages in the Inbox. Press No to return to the menu. Properties Show details for the selected MMS. Use details Displays all phone numbers contained in the message as well as the number of the sender. 1 . 2 . 3 . Use the arrow keys to select one of the displayed numbers. Press Options. Select one of the following options and press OK. Call Save Send MMS Call the selected number Save the number in the phonebook Write a new MMS message 25 English Managing files and folders 1 . 2 . 3 . 4 . and press OK. Press Menu, scroll to Select File manager and press OK. Select one of the images in the list, then press Options. Select an option from the list and press OK. Note!
The ollowing option are availale or all file in the file trctre. View Shows the images. Press Back when done. Use 1 . Select an option from the list, then press OK. To wallpaper To Phonebook Saves the image as a display background. Press OK to enable Sends the image to the phonebook. Press OK to enable Send 1 . Select an option from the list, then press OK. To MMS To Bluetooth Send the image as an MMS. Press OK, then create a message, see Creating and sending MMS Lets you send the image to other Bluetooth devices, see Bluetooth settings Details Shows the creation date and the image size. Delete Deletes the image. Delete all Deletes all images. 26 English Settings and press OK. Note!
The settings described in this chapter are carried out in standby mode. Time and date Setting the time and date 1 . Press Menu, scroll to 2 . Select Time & date and press OK. 3 . Select Set time and press OK. 4 . Enter the time (HH:MM), then press OK. 5 . Select Set date and press OK. 6 . Enter the date (DD/MM/YYYY), then press OK. Setting the time/date format 1 . 2 . 3 . 4 . 5 . 6 . 7 . Setting Auto time on/off 1 . 2 . 3 . 4 . Press Menu, scroll to Select Time & date and press OK. Select Set format and press OK. Select Time Format and press OK. Select 12 hours or 24 hours and press OK. Select Date Format and press OK. Select the desired date format and press OK. Press Menu, scroll to Select Time & date and press OK. Select Auto time and press Select On/Off and press OK. and press OK. and press OK. and press OK. 27 English and press OK. and press OK. Press Menu, scroll to Select User setup and press OK. Select Language and press OK. Scroll up/down to select a language, then press OK. Press Menu, scroll to Select User setup and press OK. Select Wallpaper and press OK. Scroll up/down to display the available wallpapers. Press OK to confirm or Back to discard changes. User setup Changing the language The default language for the phone menus, messages etc. is determined by the SIM card. You can change this to any other language supported by the phone. 1 . 2 . 3 . 4 . Display background (wallpaper) You can select from 8 different display backgrounds. 1 . 2 . 3 . 4 . 5 . Display information In standby mode the display can present date, time, and the connected network, or just the time. 1 . 2 . 3 . 4 . Display backlight Sets the delay time before the display backlight is turned off. 1 . 2 . 3 . 4 . Press Menu, scroll to Select User setup and press OK. Select LCD backlight and press OK. Select 15 sec., 30 sec. or 1 min. and press OK. Press Menu, scroll to Select User setup and press OK. Select Idle display and press OK. Select Clock only or All info and press OK. and press OK. and press OK. 28 English Tone settings (rings & tones) Tone setup 1 . 2 . 3 . 4 . 5 . Press Menu, scroll to Select Tone settings and press OK. Select Tone setup and press OK. Select Ring Tone and press OK. Select one of the available tones, the tone will be played. Press OK to confirm, or press Back to discard changes. Set up the Alarm, Opening tone, Closing tone, Message tone and Keypad tone in the same way. and press OK. 6 . and press OK. Press Menu, scroll to Select Tone settings and press OK. Select Ringtone Volume and press OK. Scroll Ringtone Volume 1 . 2 . 3 . 4 . Alert type (ring/vibrate) Incoming calls can be signaled by a ring tone and/or vibration. to change the ring volume, then press OK.
1 . 2 . 3 . 4 . and press OK. Press Menu, scroll to Select Tone settings and press OK. Select Alert type and press OK. Select the desired signaling mode and press OK. 29 English Warning and error tones Warning and error tones are used to alert the user of low battery power, phone and SIM card errors, etc. and press OK. Press Menu, scroll to Select Tone settings and press OK. Select Extra tone and press OK. Select Warning and press On/Off to enable/disable it. Select Error and press On/Off to enable/disable it. Press Done to save. 1 . 2 . 3 . 4 . 5 . 6 . Silent Silent profile is a fixed profile with SMS and ring signals disabled, while vibration and key tone settings are unchanged. and press OK. Press Menu, scroll to Select Silent and press OK. Select On/Off to enable/disable it. Press OK to save. 1 . 2 . 3 . 4 . Alternatively press and hold # to activate/deactivate Silent. 30 English Bluetooth settings You can connect wirelessly to other Bluetooth-compatible devices such as headsets. 1 . Press Menu, scroll to 2 . Select Bluetooth and press OK for the following settings:
Function on/off Select On/Off and press OK to enable/disable Bluetooth. and press OK. Visibility Select On/Off to make your phone visible/invisible to other devices. Device name Enter the name your phone should appear with for other Bluetooth devices and press Done. Search device Search for available Bluetooth audio devices. If Bluetooth is not enabled you can enable it now by pressing Yes. 1 . 2 . Select from the list of devices and press Bond to connect. When connecting with another Bluetooth device you need a shared pass code. Enter the pass code and press OK. My device Lists saved devices and enable you to add new devices. Select the device form the list and press Options. Connect Change name Delete Delete all Connect the selected device. Select the required profile, usually the Headset. Change the name of the device. Delete the device from the list. Delete all devices from the list. 31 English Audio path Select one of the options and press OK. Phone Forward BT Incoming calls are answered with the phone. Incoming calls are forwarded to Bluetooth device. Blocking functions You can disable some functions to simplify use of the phone. and press OK. Press Menu, scroll to Select Block function and press OK. Select each function you want to disable and press On. Press Done to confirm. 1 . 2 . 3 . 4 . Emergency Settings for the Emergency Call key function. See also Operation/Emergency call. and press OK. Press Menu, scroll to Select Emergency and press OK for the following settings:
1 . 2 . Activation Select one of the following options and press OK. Off Emergency call key disabled. Emergency Call key enabled. To activate, hold key for >3 seconds, or press 2 times within 1 second. Emergency Call key enabled. To activate, press key 3 times within 1 second. On Normal On (3) 32 English and press OK. Numbers list The list of numbers that will be called when the Emergency Call key is pressed. 1 . 2 . 3 . 4 . 5 . Press Menu, scroll to Select Emergency and press OK. Select Numbers list and press OK. Select Empty and press Options. Select Phonebook if you want to add a contact from the Phonebook. Alternatively press Manual. Press Enter the number and press Save. 6 . 7 . Repeat until you have max. 5 emergency numbers. See Phonebook on how to add names/numbers. To edit or delete an existing entry, select it and press Options, then select Edit or Delete and press OK. Message The SMS text message to be sent when the Emergency Call key is pressed. Press Edit and enter text, then press OK to save. Alarm information Please read this important safety information before enabling the safety information before enabling the information before enabling thethe Emergency Call function:
function:
Be careful about including numbers with automatic answering in the call list, as the alarm sequence stops once the call is answered. 33 English Voice mail 1 . 2 . 3 . 4 . and press OK. Press Menu, scroll to Select Voice mail and press OK. Select Empty and press Options. Select Phonebook if you want to add a contact from the Phonebook. Alternatively press Manual to add new. See Phonebook on how to add names/numbers. Press Save to confirm. 5 . Connect to Voice mail 1 . 2 . Select Options and press OK. Select Connect and press OK to call the voice mailbox. Alternatively press and hold 1 to call the voice mailbox. Edit To edit an existing entry, select it and press Options, then select Edit and press OK. Delete To delete an existing entry, select it and press Options, then select Delete and press OK. Note!
The voice mailox nmer i provided or network operator. 34 English and press OK. Speed dial The numerical keys 0 and 29 can be used for speed dialing. Adding speed dial numbers 1 . Press Menu, scroll to 2 . Select Speed dial and press OK. 3 . Select 0 and press Add. 4 . Select an entry from the phonebook and press OK. 5 . Repeat to add speed dial entries for keys 29. To speed dial an entry, press and hold the corresponding number key. To edit an existing entry, select it and press Options, then select Edit or Delete and press OK. Call setup 1 . 2 . Caller ID Controls display of your phone number on the recipients phone. Select an option and press OK. Set by network Hide ID Send ID Press Menu, scroll to Select Call setup and press OK for the following settings:
Use default setting by the network Never show your number Always show your number and press OK. Call waiting Select an option and press OK. See also Operation - Call waiting. Activate Deactivate Query status Enables the function Disables the function Displays if the service is active or not 35 English Call divert Set up which calls should be diverted. Select a condition and press OK, then select Activate, Deactivate or Query status (see Call waiting above) for each. Div . voice calls Div . unreach Div . no reply Divert if busy Cancel diverts Diverts all voice calls. Diverts incoming calls if the phone is turned off or turned off or out of range. Diverts incoming calls if unanswered. Diverts incoming calls if the line is busy. Do not divert calls Call barring The phone can be restricted to disallow certain types of calls. Note!
To change these settings a password is needed. Contact your network operator to get the password. Outgoing calls All calls Internat. calls Int. except home User cannot call international numbers except to Press OK then select:
User can answer incoming calls but not dial out. User cannot call international numbers. Incoming calls All calls When roaming Cancel all the country associated with the SIM card. Press OK then select:
User can dial out but not receive incoming calls. User cannot receive incoming calls while roaming
(operating in other networks). Cancel all call barring (password needed) Answer mode Select Open to answer and press On to be able to answer incoming calls by cover opening. Select Any key and press On to be able to answer incoming calls by pressing any key. 36 English and press OK. Press Menu, scroll to Select Messages and press OK. Select SMS settings and press OK for the following settings:
Messages SMS settings 1 . 2 . 3 . Profile set This number is needed to use the SMS function. The number can be obtained from the network operator. 1 . Add/edit the message service phone number. Use the side keys to move the cursor. Press Clear to erase. Press Save to save the new number. 2 . Memory status Displays the percentage of memory space used on the SIM card and phone memory. Pref . storage 1 . Select SIM to store messages on the SIM card, or Phone to store messages in the phone memory. Press OK to confirm. 2 . 37 English and press OK. Press Menu, scroll to Select Messages and press OK. Select MMS settings and press OK for the following settings:
MMS settings 1 . 2 . 3 . Access point The access point is needed to use the MMS function. The correct settings can be obtained from the network provider. Select the Access point of your network provider. Select Activate profile and press OK to enable it. If your network provider is not in the list, do the following:
1 . Select Edit profile to edit the Access point. Profile name Homepage Data account Connection type Edit the profile name, then press Done Edit the access point address, then press Done Select your service providers data account, then press OK Select connection type (WAP/HTTP), then press OK. Edit Proxy address and Proxy port if needed, then press Done Write the desired user name, then press Done Write the desired password, then press Done. Press Done, and press Yes to save or No to go back. User name Password 2 . Memory status Displays the number of messages saved and the memory space left in the phone. 38 English and press OK. Press Menu, scroll to Select Messages and press OK. MMS settings 1 . 2 . Data account The data account is needed to use the MMS function. The correct settings can be obtained from the network provider. 1 . Select your network provider and press Edit. Account name APN User name Password 2 . Press Done, and press Yes to save or No to go back. Edit the account name, then press Done. Edit the APN address, then press Done Write the desired user name, then press Done Write the desired password, then press Done. Press On to enable Smart ABC/eZiType, see Text inpt. Select a dictionary (language) and press OK to confirm. Press Menu, scroll to Select Network setup and press OK. Select one of the following options and press OK to confirm. and press OK. Automatic Manual Network is selected automatically. A list of available network operators is displayed (after a short delay). Select the desired operator and press OK. 39 Spell support 1 . 2 . Network setup 1 . 2 . 3 . English Services A number of features included in this guide are called Services. These are special services that you arrange through your wireless service provider. Security settings 1 . 2 . SIM lock The SIM card is protected with a PIN code (Personal Identification Number). The phone can be set to ask for the PIN code on startup. Select On/Off and press OK to enable/disable SIM card lock. Press Menu, scroll to Select Security and press OK. and press OK. Note!
You need to input the current PIN code to disable/enable SIM lock. Phone lock Select On/Off and press OK to enable/disable the Phone lock. Note!
You need to input the current Phone code to change this setting. The default Phone code is 1234. Enter the current code and confirm with OK Enter a new code and confirm with OK. Enter the new code again and confirm with OK. PIN / PIN2 / Phone password To change the PIN codes or the phone lock password:
1 . 2 . 3 . Reset Reset the phone to the factory settings. Input the phone lock password and press OK to reset. 40 English Safety instructions Warning!
The unit and the accessories can contain small parts . Keep all of the equipment out of the reach of small children . Operating environment Follow the rules and laws that apply wherever you are, and always turn off the unit whenever its use is prohibited or can cause interference or hazards. Only use the unit in its normal user position. This unit complies with guidelines for radiation when it is used either in a normal position against your ear, or when it is at least 7/8 of an inch
(2.2cm) from your body. If the unit is carried close to your body in a case, belt holder or other holder, these holders should not contain any metal, and the product should be placed at the distance from your body specified above. Make sure that the distance instructions above are followed until the transfer is complete. Parts of the unit are magnetic. The unit can attract metal objects. Do not keep credit cards or other magnetic media near the unit. There is a risk that information stored on them can be erased. Medical units The use of equipment that transmits radio signals, for example, mobile phones, can interfere with insufficiently protected medical equipment. Consult a doctor or the manufacturer of the equipment to determine if it has adequate protection against external radio signals, or if you have any questions. If notices have been put up at health care facilities instructing you to turn off the unit while you are there, you should comply. Hospitals and other health care facilities sometimes use equipment that can be sensitive to external radio signals. 41 English Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. Persons with pacemakers:
Should always keep the unit more than 6 inches (15cm) from their pacemaker when the it is turned on Should not carry the unit in a breast pocket Should use the ear opposite the pacemaker to minimize the potential for interference If you have any reason to suspect that interference is taking place, turn the phone off immediately. Areas with explosion risk Always turn off the unit when you are in an area where there is a risk of explosion. Follow all signs and instructions. There is a risk of explosion in places that include areas where you are normally requested to turn off your car engine. In these areas, sparks can cause explosion or fire which can lead to personal injury or even death. Turn off the unit at filling stations, and any other place that has gas pumps and auto repair facilities. Follow the restrictions that apply to the use of radio equipment near places where fuel is stored and sold, chemical factories and places where blasting is in progress. Areas with risk for explosion are often but not always clearly marked. This also applies to below decks on ships; the transport or storage of chemicals; vehicles that use liquid fuel (such as propane or butane); areas where the air contains chemicals or particles, such as grain, dust or metal powder. Emergency calls Important!
Mobile phones such as this unit use radio signals, the mobile phone network, the terrestrial network and user-programmed functions. This means that connection cannot be guaranteed in all circumstances. 42 English Therefore, you should never rely solely on a mobile phone for very important calls such as medical emergencies. Vehicles Radio signals can affect electronic systems in motor vehicles (for example, electronic fuel injection, ABS brakes, automatic cruise control, air bag systems) that have been incorrectly installed or are inadequately protected. Contact the manufacturer or its representative for more information about your vehicle or any additional equipment. Do not keep or transport flammable liquids, gases or explosives together with the unit or its accessories. For vehicles equipped with air bags:
Remember that air bags fill with air with considerable force. Do not place objects, including fixed or portable radio equipment in the area above the airbag or the area where it might expand. Serious injuries may be caused if the mobile phone equipment is incorrectly installed and the airbag fills with air. It is prohibited to use the unit while in flight. Turn off the unit before you board a plane. Using wireless telecom units inside a plane can pose risks to air safety and interfere with telecommunications. It may also be illegal. 43 English Driving Safely Use of this unit alone or with headphones (even if used only in one ear) while driving a motor vehicle or riding a bicycle is not recommended and is illegal in some areas. Check and obey the laws and regulations on the use of mobile devices like this unit in the areas where you drive. Be careful and attentive while driving. If you decide to use this unit while driving or riding a bicycle, keep in mind the following guidelines:
Give full attention to driving and to the road . Using a mobile device while driving may be distracting. If you find it disruptive or distracting while operating any type of vehicle, riding a bicycle, or performing any activity that requires your full attention, pull off the road and park before making or answering a call if driving conditions require. Get to know your phone and its features such as phone book, call memory, and speakerphone . These features help you to place your call without taking your attention off the road. See the applicable portion of this users guide for more information. Use a hands-free device . Add an extra layer of convenience and safety to your unit with one of the many hands-free accessories available. Use of a headset or other hands-free device may be legally required. Several states have in recent years passed laws making it unlawful to operate a motor vehicle while talking on a wireless phone without use of a headset, speakerphone, or other hands-free device. County and municipal ordinances may also limit or ban wireless conversations for automobile drivers. You should therefore check the status of such laws in your area and in locations to which you travel by car, whether or not you otherwise follow the preferred safety practice of routinely using a hands-free device. For SMS text messaging, it is a recommended safety practice that you never send or view received text messages while driving; in California, and likely other states in the future, SMS messaging by a driver is also a legal violation. Position phone within easy reach . Keep your eyes on the road. If you get an incoming call at an inconvenient time, let your voicemail answer it for you. 44 English Assess the traffic before dialing, or place calls when you are not moving or before pulling into traffic. Try to plan calls when your car will be stationary. Never dial, send SMS text messages, or enter other text while you are driving. Let the person you are speaking with know you are driving . If necessary, suspend the call in heavy traffic or hazardous weather conditions. Driving in rain, sleet, snow, ice, fog, and even heavy traffic can be hazardous. Do not take notes, look up phone numbers, or perform any other activities that require your attention while driving . Jotting down a to-do list or flipping through your address book takes attention away from your primary responsibility, driving safely. Do not engage in stressful or emotional conversations that may be distracting . Make people you are talking with aware you are driving and suspend conversations that have the potential to divert your attention from the road. 45 English RF Exposure Information (SAR) This model phone meets the governments requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the model phone as reported to the FCC when tested for use at the ear is 0.45 W/kg and when worn on the body, as described in this user guide, is 0.57 W/kg (Body-worn measurements differ among phone models, depending upon available enhancements and FCC requirements.) While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: WS5DORO410G 46 English For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 5/8 inch (1.5 cm) from the body. Use of other enhancements may not ensure compliance with FCC RF exposure guidelines. If you do no t use a body-worn accessory and are not holding the phone at the ear, position the handset a minimum of 5/8 inch (1.5 cm) from your body when the phone is switched on.
*In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. SAR values may vary depending on national reporting requirements and the network band. Hearing Aid Compatibility Your mobile device model complies with FCC rules governing hearing aid compatibility. These rules require an M3 microphone or higher value. The M-value, shown on the device box, refers to lower radio frequency
(RF) emissions. A higher M-value generally indicates that a device model has a lower RF emissions level, which may improve the likelihood that the device will operate with certain hearing aids. Some hearing aids are more immune than others are to interference. Please consult your hearing health professional to determine the M rating of your hearing aid and whether your hearing aid will work with this device. FCC ID: WS5DORO410G 47 Troubleshooting Phone cannot be switched on Battery charge low Battery incorrectly installed Failure to charge the battery Battery or charger damaged Battery recharged in temperatures
<32 or >104F (< 0C or > 40C) Charger incorrectly connected to phone or power socket Standby time decreases Battery charge capacity too low Too far from base station, phone is constantly searching for signal Connect the power adapter and charge the battery for hours. Check the installation of the battery. Check the battery and charger. Improve the charging environment. Check the charger connections. Install a new battery. Searching the network consumes battery power. Find a place with a stronger signal, or temporarily turn off the phone. Failure to place or receive calls Call barring activated Deactivate call barring. If this does not solve the problem, contact the network operator. PIN code not accepted Wrong PIN code entered too many times Enter the PUK code to change the PIN code, or contact the network operator. SIM card error SIM card damaged SIM card incorrectly installed SIM card dirty or damp Check the condition of the SIM card. If it is damaged, contact the network operator. Check the installation of the SIM card. Remove the card and reinstall it. Wipe the contact surfaces of the SIM card with a clean cloth. Failure to connect to network SIM card invalid No coverage of GSM service Signal too weak Contact the network operator. Contact the network operator. See Weak signal below. Weak signal Too far from base station Network congestion Try again from another location. Try calling at a later time. Echo or noise Regional problem from bad network relay Hang up and redial. This may switch to another network relay. Failure to add a contact Phonebook memory full Failure to set a function Function not supported or subscribed from network Delete contacts to free up memory. Contact the network operator. Care and maintenance Your unit is a technically advanced product and should be treated with the greatest care. Negligence may void the warranty. Protect the unit from moisture. Rain/snowfall, moisture and all types of liquid can contain substances that corrode the electronic circuits. If the unit gets wet, you should remove the battery and allow the unit to dry completely before you replace it. Do not use or keep the unit in dusty, dirty environments. The units moving parts and electronic components can be damaged. Do not keep the unit in warm places. High temperatures can reduce the lifespan for electronic equipment, damage batteries and distort or melt certain plastics. Do not keep the unit in cold places. When the unit warms up to normal temperature, condensation can form on the inside which can damage the electronic circuits. Do not try to open the unit in any other way than that which is indicated here. Do not drop the unit. Do not knock or shake it either. If it is treated roughly the circuits and precision mechanics can be broken. Do not use strong chemicals to clean the unit. The advice above applies to the unit, battery, mains adapter and other accessories. If the phone is not working as it should, please contact the place of purchase for service. Dont forget the receipt or a copy of the invoice. Warranty and technical data This product is guaranteed for a period of 24 months from the date of purchase. In the unlikely event of a fault occurring during this period, please contact the place of purchase. Proof of purchase is required for any service or support needed during the guarantee period. This guarantee will not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, non-
maintenance or any other circumstances on the users part. Furthermore, this guarantee will not apply to any fault caused by a thunderstorm or any other voltage fluctuations. As a matter of precaution, we recommend disconnecting the charger during a thunderstorm. Batteries are consumables and are not included in any guarantee. This guarantee does not apply if batteries other than DORO original batteries are used. Specifications Network:
Dimensions: 3.86 in x 2 in x .75 in (98 mm x 51 mm x 19 mm) Weight:
Battery:
3.5 oz (99 g) (including battery) 3.7V/800 mAh Li-ion battery 850/DCS1800/PCS1900 Triple Band 2009 Doro AB. All rights reserved. Bluetooth is a registered trademark of Bluetooth SIG, inc. eZiType is a trademark of Zi Corporation. vCard is a trademark of the Internet Mail Consortium. English Version 1.0