SAFETY NOTE 1, This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. 2, Children shall not play with the appliance. 3, Cleaning and user maintenance shall not be made by children without supervision. 4, If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 5, WARNING: the drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts. 6, The instructions shall state that the A-weighted emis sion sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA 70 dB(A). 7, The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time. 8, The type of driven part the drive is intended for. 9, WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions. 10, Do not allow children to play with fixed controls. Keep remote controls away from children 11, Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary 12, Watch the moving shutter and keep people away until he shutter is completely closed 13, WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. 14, Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation Tubular Motor-
BR-28-0228 Specification
(A-02) Product introduction One motor can store maximum 20 channels; after fully stored, if pair new channels, only the last one will be covered circularly. Features:
Built-in Receiver Electronic Limit Switch Direction Stall Protection Speed Regulation Jog & Tilt Preferred Stop Position Low Power Consumption Restore Factory Setting 50 0 Working Temperature Parameter (More models and parameters are subject to the nameplate) Type Rated Torque(N.m) Rated Speed(RPM) The Input Voltage(V) Rated Power(W) Emission Frequency(MHz) DM28LEU/S 2.0N.m 28RPM USB 5V 2A 15W 433.92MHz Motor installation Driving tube must be close-fitting with crown and drive adapter. Choose crown and drive adapter based on the driving tube. Drive tube Drive tube Crown Runner Circlip 1 0 1 0 Stroke support Button specification 5V USB charging interface Tail insert bracket Up button Stop button Down button Setting button P2 P2 P2 M Lithium Cell 3V 1 0 Setting button(P1) Lithium battery switch Note: dial lithium battery switch, 0 is off switch, 1 is turn on switch. Operation note Please read following points of attention carefully before setting. 1. Before the first use, please charge, to ensure full power after the use of(The motor uses a 5V USB charger to charge). Motor stop running when the supply voltage is lower than 8.0V,and it will restart again when the voltage is greater than 8.5V When the power voltage is lower than 7.0 V, the motor stops and the buzzer chirps. When the voltage is greater than 7.5v, it can be started again. When the voltage is lower than 10V, when the motor is running continuously, the alarm will be made and the buzzer will be called 10 times. When the power voltage is lower than 10.5 V, low voltage prompt, red light interval 1s frequency flash, total 10 times. During the charging process, the green light flashes between 1S and 1S, and the green light is always on after the battery voltage is greater than 12.4V, and the charging is completed. 2. Dont operate motors when low voltage alarm 3. Operating The valid interval of the emitter button is 10s,the emitter will quit the set after 10s. The motor will run or beep for hint,please do the next step after the hint. 4. Set the limit position After the upper/lower limit setting,and the upper/lower limit position cant at the same position. After the limit setting,with power off and memory function. Into the match-code status 2 minutes later,it will quit out the setting limits status automatically. Restore factory settings to clear all settings. 5. When the motor running without any operation, the maximum running time is 6 minutes,it will stop automatically. 6. If the emitter lost,please setting up again with the new emitter. READING 2.2, Run to the 3rd limit position Stop The motor runs automatically to the 3rd limit position Press 2s P2 2.3, Clear the 3rd limit position P2StopStop Run for hint x1 Di x1 Run for hint x1 Di x1 Run forhint x1 Di~ x1 Press 1s Press 1s Press 1s 3 Adjust limits Clear the 3rd limit position is ok 6 Speed Regulation P2Up/DownUp/Down Run for hint x1 Di x1 P2 Press 1s Run for hint x1 Di x1 Run for hint x2 Press 1s Press 1s Run for hint x1 Di x1 Run for hint x2 Press 1s Press 1s The motor running speed is improved The motor running speed is reduced 3.1, Adjusting the upper limit position Up+StopUp/DownUp+Stop Note: If the motor no response, it has already been the Max. or Min speed; The continuous motor speed has 3 grades, 20r/min, 24r/min, 28r/min, and the factory default is the fastest speed. I O P E R A T O N G U D E I
Successfully switch direction 3.2, Adjusting the lower limit position Down+StopUp/DownDown+Stop Press 5s Press 1s Press 2s Motor run upward / stoprunning / run downward Adjust the required lower limit position Run for hint x2 Di x3 Short press P1 Note: This operation should be carried out under the conditions of motor has the limit. Motor P1 button operation 1, Short press function Adjust the required upper limit position Run for hint x2 Di x3 or or
The new upper limit is OK The new lower limit is OK Successfully switch direction Press 5s Press 1s Press 2s Note: After entering the limit fine-tuning mode, the original 3rd limit position will not be deleted;If there is no button operation in 2 minutes, 2 minutes time limit, motor chance to rotate the hint, and automatically exit the limit fine-tuning mode;After fine-tuning the up/down limits can not be in the same position. Run forhint x1 Di~ x1 Enter to the process of adjusting the limit Run forhint x1 Di~ x1 Enter to the process of adjusting the limit
4 Pair additional emitter Method one P2 P2 P2 2, Paring / Pair additional emitter / Remove one emitter Run for hint x1 Di~ x1 Enter paring status Repeat paring operation Press 2s Loosen P1 Note: in the factory mode, enter paring status; In the user mode, enter pair additional emitter or remove one emitter. Run for hint x1 Di~ x1 Run for hint x2 Di x3 Switch to jog mode Switch to running mode Method one P2 P2 P2 5 Remove one emitter Note: when under jog mode, press up/down button once, the motor will be jog running, if press more than 2S, the motor will be continously running. Run for hint x1 Di x1 Run for hint x1 Di x1 Run for hint x2 Di x3 P2 P2 P2 One emitter have been removed Run for hint x1 Di x1 Run for hint x1 Di x1 Run for hint x2 Di x3 P2 P2 P2 New emitter is paired to the motor 3, Radio lock mode Run for hint x2 Di x2 Press 1s Press 1s Press 1s The motor enters Radio Lock mode Method two P2 P2 Stop Press 6s Loosen P1 Run for hint x1 Di x1 Run for hint x1 Di x1 Run for hint x2 Di x3 P2 P2 New emitter is paired to the motor Note: When the motor enters the radio lock mode, all the setting memory will be saved, only the radio receiving function has been disabled. Press 1s Press 1s Press 2s Method three Stop Run for hint x1 Di~ x1 Run for hint x2 Di x3 4, Switch direction Run for hint x3 Di x3 Successful change the direction Press 2s Loosen P1 Press 2s Note: Emitter is the paired emitter for master motor, is unpairing emitter; After the emitter is added, keep all the original settings of the motor. 5, Restore factory setting New emitter is paired to the motor Press 10s Loosen P1 Note: After the success of the reversing,retain all motor original settings. Run for hint x4 Di x4 Restore factory setting successfull Note:After the Reset to factor mode,will delete all previous system function setting and the emitter code. Press 14s Loosen P1 Fault and solution NUMBER ISSUE POSSIBLE CAUSES SOLUTION Press 1s Press 1s Press 1s Method two Stop Run for hint x1 Di~ x1 Run for hint x2 Di x3 Press 2s Loosen P1 Press 2s Note: are all of the code emitters,this method only can delete the emitter not the emitter ;After deleting the emitter, keep all the settings of the motor (the limit is reserved for the previous setting). One emitter have been removed 1 The motor doesn't run a, The battery is not activated. b, The emitter hasn't been paired;
c, If press P1 button for long time, the motor no reaction, probably the board is short circuit, or the motor is broken. a, Activate the motor afterfully charged b, Paring again;
c, Contact after sales service for more details Factory mode 1 Paring Stop If you need to reverse the rotateon of the motor controlled by the emitter,pls switch channel address. Run for hint x1 Di~ x1 Press 2s Loosen P1 1 0 1 0 Power off to 0 Power on to 1 T<10s Run for hint x1 T<10s Run for hint x2 Di x3 Paring is OK Press 2s Note: In the user mode, power on the code can also operate;If 10s,no stay setting up emitter preess or no legal stop button code,10s to the limit,will automatically exit the setting up mode. 2 Switch rotating direction(optional) UpUp+Down Method one The curtain run downward Run for hint x1 Press 1s Press 2s Method two Run for hint x3 Di x3 Press 10s Loosen P1 Note: After the success of the reversing,retain all motor original settings. 3 Setting upper and lower limit During the limit setting mode, press UP/DOWN once, the motor will jog running, if you press UP/DOWN 2S, the motor will run continuously. 3.1, Setting the upper limit UpStopUp+Stop The curtain run upward The upper limit The curtain stops running Run for hint x2 Di x3 Upper limit is OK Press 2s Run to the desired upper position Press 1s Press 2s 3.2, Setting the lower limit DownStopStop+Down The curtain run downward The lower limit The curtain stops running Run for hint x2 Di x3 Lower limit is OK
Press 2s Run to the desired lower position Press 1s Press 2s User mode 1 Jog mode & running mode switch Up+DownStop Run for hint x1
Press 5s Press 1s 2 3rd preferred stop position setting 2.1, Set the 3rd limit position P2StopStop The 3rd limit position setting : If you have already set the upper and lower limit, then you can set the 3rd limit between upper and lower limit. Run for hint x1 Di x1 Run for hint x1 Di x1 Run for hint x2 Di x3 P2 3rd limit position is ok Press 1s Press 1s Press 1s preferred stop position
(Any position) Run to the req-
uired preferred stop position Tubular Motor-
DM28LEU/S Specification
(A-02) FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.