FCC ID: YE3600-3165D2W Rugged Tablet

Rugged Handheld Tablet BASIC OPERATION GUIDE DT362GL INTRODUCTION The DT Research DT362GL Handheld Rugged Tablet features the integration of a high brightness 6 capacitive touch screen and a high performance yet energy efficient processor within a slim, lightweight, durable package. With built-in Wi-Fi, Bluetooth and a smart card reader as well as options for back camera, barcode scanner, GNSS and UHF RFID reader, this robust tablet offers seamless information capture and transmission for improved workflow. Rated IP65 and MIL-STD-810G, the DT362GL Handheld Rugged Tablet provides reliable operation in harsh, mission-critical environments. PACKAGE CONTENTS One DT362GL One Battery Pack and Handstrap AC-DC Power Adapter Basic Operation Guide

* The actual package contents may vary depending on the configuration acquired. PRECAUTIONS Always exercise care when operating and handling the DT362GL Do not disassemble any portion of the DT362GL, as this will void any product warranty. Do not use any power adapter or charging cradle other than the one provided with the tablet or acquired from the manufacturer or its partners. In the unlikely event that abnormal noise, strange odor, or smoke is present, immediately power down the DT362GL and disconnect all power sources. Please report the problem to your device provider immediately. Input/ Output Ports Button Functions A USB Type-C Port (power input) BUTTON ACTION 1 2 3 power button Trigger Buttons Battery Latch Data Capture Modules B Barcode Scanner (optional) C Smart Card Reader D Back Camera (optional) E UHF RFID Reader (optional) 2 OPERATION Powering ON and OFF To activate DT362GL, push and quickly release the Power Button. The display will come on in a few seconds. To put the DT362GL in standby mode, push and quickly release the Power Button. To turn the DT362GL off for extended storage, power off safely using any software function that shuts down computer provided in the software operating system. The battery packs shipped with your tablet may be low in power - please use the AC-DC adapter with the DT362GL when setting up for the first time to fully charge the battery pack. To conserve power, push and quick release the Power Button to make the tablet in standby mode while not in use. Pushing briefly on the same butt on will wake up the system. When the battery pack is charging, the blue-colored Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Unplug/ replug the AC-DC adapter to the DT362GL/ DT362Q a few times to activate the charging For DT362GL, avoid using the Power Button (hold 4+ seconds feature) to turn off the tabletthis form of hardware shutdown is intended to be a means of recovery from lockups, and not as normal NOTE:

NOTE:

NOTE:

process. NOTE:

operation.. 3 If the power up (from Standby mode or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be established. Start Up Wireless Networking Wireless LAN hidden custom antenna. The DT362GL is often delivered with an embedded (user-inaccessible) 802.11ac LAN adapter equipped with a Through the support of typical WLAN adapters, the DT362G should be able to detect all 802.11 access points in the vicinity for you to select the access point of your choice for connection. The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT362G and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access. When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc. Refer to the access point operating manuals for setting up the 802.11 access points. Bluetooth The Bluetooth configuration application is enabled from the System Tray or from the Windows Mobility Center. Follow the instructions and options provided within the application to configure and invoke Bluetooth connectivity with the corresponding peripherals. 4 Data Capture Module Operation Guide If your DT362GL comes with a RFID Reader refer to the steps below to configure the settings. The optional UHF RFID reader supports EPC Gen2V2 and ISO 18000-63 standard. To develop an application to use the UHF RFID reader, contact your device provider for a UHF RFID reader API package To ensure the system performance, turn on only the symbologies you are going to use. UHF RFID Reader:

NOTE:

For More Support Users can download the Tablet Modules Basic Operation Guides from the DT Research website. 5 Intel Pentium Silver Quad-Core, 1.10GHz (up to 2.70GHz) Microsoft Windows 10 IoT Enterprise 6 LED-backlight capacitive touch screen Wi-Fi 802.11ac, 2.4GHz/ 5GHz dual band; Bluetooth 4.2 LE 1 power button, 2 trigger buttons DT362GL 8GB 256GB 720 x 1440 USB Type-C x 1

(data transmitting and charging. Data transmitting only available in one insertion direction) Full slot, reads ISO 7816 T=0, T=1; 1.8/3/5V smart card Smart Card/CAC Reader Mechanical and Environmental AC/DC Adapter Battery Pack Enclosure Weight Regulatory Operating Temperature Humidity Input: 100 240V AC; Output: 20V DC, 3.25A Hot swappable battery, 3100mAh ABS + PC plastics 1.4 lbs/ 650 g FCC Class B, CE, RoHS compliant Operation: -10C to 50C (14F to 122F ) Storage: -20C to 60C (-4F to 140F) 0% 90% non-condensing Dimensions (H x W x D) 7.6 x 3.7 x 1.2 in/ 192 x 95 x 31 mm Specifications:

Item System CPU RAM Storage Display Operating System Display Resolution Network Interface Control Switch and Buttons I/O Ports USB port 6 DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com Copyright 2020, DT Research, Inc. All Rights Reserved. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information (SAR) This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid after searching on FCC ID:

YE3600-3165D2W

Federal Communication Commission Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [B] est conforme la norme NMB-003 du Canada. DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 Copyright 2020, DT Research, Inc. All Rights Reserved. BOG081920 DT361AM/ DT361AD ENG Rugged Tablet DT361AM/ DT361AD Thank you for acquiring the DT361AM/ DT361AD, part of DT Researchs line of Rugged tablets. Featuring a slim yet robust enclosure, the DT361AM/ DT361AD with 6 Capacitive touch screen is powered by the Intel processor, offering optimal combinations of performance and power savings. The DT361AM/ DT361AD is available with Microsoft Windows operating system and features web browser, client/ server computing software, media player, accessories, and applications support. PACKAGE CONTENTS One DT361AM/ DT361AD with Battery Pack and Handstrap AC-DC Power Adapter with Power Cord Basic Operation Guide This device complies with Part 15 of the FCC Rules. INTRODUCTION DT361AM A DT361AD 5 6 4 3 B C D Input/ Output Ports A B Smart Card Reader (DT361AM) SD Card Reader (DT361AD) LAN Port C USB 3.0 Port USB Type-C Port

(as power input) D Button Functions BUTTON ACTION BUTTON ACTION 1 2 3 Power Button NVIS/ Normal Mode Toggle

(optional) Programmable Buttons 4 5 6 Brightness Control Buttons Waki-talkie Communication Buttons Battery Latch *Push the switch up to unlock the latch, then slide the latch left to remove the battery. 1 2 warranty. NOTE:

PRECAUTIONS Always exercise care when operating and handling the DT361AM/ DT361AD. Do NOT apply excessive pressure to the display screen. We recommend using the Digital Pen (optional) to keep the screen clean. Avoid prolonged exposure of the display panel to any strong heat source. Wherever possible, the DT361AM/ DT361AD should face away from direct light to reduce glare. If the AC-DC power adapter is used to recharge or power the tablet, do NOT use any AC-DC adapter other than the one provided or acquired from the manufacturer or its partners. In the unlikely event that smoke, abnormal noise, or strange odor is present, im-

mediately power off the DT361AM/ DT361AD and disconnect all power sources. Report the problem to your device provider immediately. Never attempt to disassemble the DT361AM/ DT361AD, as this will void the To obtain protection consistent with any IP rating for the device, the I/O (audio, power, USB, card reader, etc.) port doors must be closed. If the IP protection is compromised by mishandling or misuse, such as by leaving port doors open or improperly closed, any resulting product damage will not be covered under any DT Research warranty. BASIC FEATURES The DT361AM/ DT361AD rugged tablet integrates a dual mode switchable NVIS or high-brightness touchscreen, USB ports, and embedded networking elements such as wireless LAN and Bluetooth. A DT361AM/ DT361AD typically integrates an 802.11ac wireless LAN (WLAN) adapter that may connect to other wireless devices or access points. If your DT361AM/

DT361AD does not come with such a network adapter, please consult your device provider to establish the desired network connectivity. 2 3 NOTE:

NOTE:

NOTE:

OPERATION Powering ON and OFF To activate the DT361AM/ DT361AD, push and quickly release the Power Button. The display will come on in a few seconds. To put the DT361AM/ DT361AD in Standby mode, push and quickly release the Power Button. To turn the DT361AM/ DT361AD off for extended storage, power off safely using any software function that shuts down computer provided in the software operating system. The battery pack shipped with your tablet may be low in powerplease use the AC-DC adapter with the DT361AM/ DT361AD when setting up for the first time to fully charge the battery pack, or use the optional battery charger kit. To conserve power, use (push and quick release) the Power Button to put the tablet in Standby mode while not in use. Pushing briefly on the same button will wake up the system within seconds. Avoid using the Power Button (hold 4+ seconds feature) to turn off the tablet this form of hardware shutdown is intended to be a means of recovery from lockups, and not as normal operation. If the power up (from Standby mode or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be established. Conguring the Rugged Tablet The DT361AM/ DT361AD may be configured using the utilities and methods dictated by the software operating system. The DT361AM/ DT361AD should be configurable for various properties such as user profiles, network features, and several system Start Up elements. NVIS Mode and Screen Brightness Control (optional) When power button is pressed to power on the unit, power LED will flash orange once to indicate the unit is booting. Unit will boot into NVIS mode with zero nit brightness by default and display will be dark. You can press the Brightness Up and Brightness Down buttons to set NVIS mode display to desired brightness

(up to 20 nits). To toggle between NVIS and high-brightness display mode, press the NVIS/

Normal Mode Toggle button. When changed from NVIS mode to high-brightness mode, display brightness percentage will be same as the brightness level set in NVIS mode before toggling. Use brightness control buttons to set desired brightness level. When changed from normal display mode to NVIS mode, display brightness will be set to 0 nit

(display is dark) and you need to use brightness control buttons to change display to desired brightness. Brightness up, Brightness down, NVIS/Normal toggle, Windows Key and Control Center functions are fixed and not user programmable. Two programmable buttons on left side can be programmed through Button Manager. 4 5 Wireless Networking Wireless LAN The DT361AM/ DT361AD is often delivered with an embedded (user-inaccessible) 802.11ac WLAN adapter equipped with a hidden custom antenna. Through the support of typical WLAN adapters, the DT361AM/ DT361AD should be able to detect all 802.11 access points in the vicinity to select the access point of choice for connection. The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT361AM/

DT361AD and the access points have to match. The SSID is case-sensitive and it is recommended to enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access. When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc. Refer to the access point operating manuals for setting up the 802.11 access points. Bluetooth The Bluetooth configuration application is enabled from the System Tray or from the Windows Mobility Center. Follow the instructions and options provided within the application to configure and invoke Bluetooth connectivity with the corresponding peripherals. Canada

- English:

- French:

USING THE RUGGED TABLET Peripherals Support Through its USB 3.0 port, the DT361AM/ DT361AD supports a wide range of USB-based peripherals. These peripherals are applicable for software installation, applications storage, data storage, and system software recovery and updates. For More Support Users can download the Tablet Modules Basic Operation Guides from the DT Research website. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareilest conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. Cet quipement est conforme aux limites dexposition aux rayonnements ISED tablies pour un environnement non contrl. Lutilisateur final doit suivre les instructions spcifiques pour satisfaire les normes. Cet metteur ne doit pas tre co-

implant ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conu pour rpondre aux exigences dexposition aux ondes radio tablie par le dveloppement nergtique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus leve signale en vertu de cette norme lors de la certification de produit utiliser lorsquil est correctement port sur le corps. 6 7 1. the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

2. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

3. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and 4. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. 1. le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal;

2. pour les dispositifs antenne (s) dtachable (s), le gain d'antenne maximal autoris pour les dispositifs dans les bandes 5250-5350 MHz et 5470-5725 MHz doit tre tel que l'quipement soit toujours conforme la norme e.i.r.p. limite;

3. pour les dispositifs antenne (s) dtachable (s), le gain d'antenne maximal autoris pour les dispositifs de la bande 5725-5850 MHz doit tre tel que l'quipement soit toujours conforme la norme e.i.r.p. les limites, le cas chant; et 4. le cas chant, le (s) type (s) d'antenne, le (s) modle (s) d'antenne et l'angle (s) d'inclinaison le plus dfavorable ncessaire (s) pour rester conforme (e) au p.e. L'exigence relative au masque d'lvation nonce la section 6.2.2.3 doit tre clairement indique. FCC RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been tested for use against the body with 0mm separation in Specific Absorption Rate (SAR) testing. User must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information Unique Identifier Trade Name:

Model No.: DT361AM/ DT361AD Responsible Party U.S. Contact Information DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label is in removable battery compartment, it could be easily found by removing the battery cover. 6 7 RF Exposure Information(RED) This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0cm must be maintained between the users body and the handset, including the antenna. The band 5150-5350 MHz for this device are restricted to indoor use only within all European Union countries. Hereby, [DT Research, Inc.] declares that the radio equipment type [DT361AM, DT361AD] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

http://www.dtresearch.com. Maximum EIRP for EU Bluetooth:2402MHz-2480MHz Bluetooth LE:2402MHz-2480MHz 2.6dBm 1.52dBm Wifi: 2412MHz-2472MHz/2422MHz-2462MHz 13.74dBm Wifi: 5150MHz-5725MHz 11.96dBm 6 7

DT Research, Inc. FCC ID Label FCC ID.: YE3600-3165D2W 3RD FL NO 36 WUQUAN 7TH RD WUGU DISTRICT, NEW TAIPEI, Taiwan TEL: 886-2-2298-1039#382

DT Research, Inc. The FCC ID and will be placed on the equipment as shown in the photograph below. FCC ID.: YE3600-3165D2W 3RD FL NO 36 WUQUAN 7TH RD WUGU DISTRICT, NEW TAIPEI, Taiwan TEL: 886-2-2298-1039#382

DT Research, lnc.

San Jose, CA 95131, USA

www.dtresearch.com

Product Name: Rugged Tablet

Model No.: DT361AD

Input: 15V 3A Max

DT Research, lnc.

San Jose, CA 95131, USA

www.dtresearch.com

Product Name: Rugged Tablet

Model No.: DT361AD

Input: 15V 3A Max

Contains FCC ID:YE3600-3165D2W

Contains IC:7647A-6003165D2W

Assembled in Taiwan

Contains FCC ID:YE3600-3165D2W

Contains IC:7647A-6003165D2W

Assembled in Taiwan

Label location: please see external photo on page 6.

Color

Background- COOL BLACK

Letter/LOGO/Block - WHITE

Material 8B35 t = 0.178

Adhesive 3M 467

DIM: MM (INCH)

PART NAME

Model Label DT361AD

UNIT

MM

DT Research, Inc. Taiwan Branch

TOL UNLESS NOTED

PART NO.

.X ±0.1

.XX

±0.1

ANGLE ±0.1°

MATERIAL

8B35 t = 0.178

.

DWG. NO.

DT361ADLB01

DATE: 03/18/21’

:

REV:00 SH:1/1

APPROVE

DESIGN

DRAWN

Wing

SCALE

1:1

DON'T SCALE

DRAWING

DT Research, Inc. Date: 2021-7-14 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: YE3600-3165D2W To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with DT Research, Inc. This authorization is valid until further written notice from the applicant. Sincerely, Signature:

Print Name: JS Hsu Title: Manager On behalf of Company: DT Research, Inc. Telephone: 886-2-2298-1039 ext. 309 E-mail: js_hsu@dtri.com

DT Research, Inc.

To:

Federal Communications Commission

Office of Engineering and Technology Laboratory Division

7435 Oakland Mills Rd.

Columbia MD 21046

From: DT Research, Inc.

Regarding: Confidentiality Request regarding application for FCC ID: YE3600-3165D2W

LONG TERM CONFIDENTIALITY

Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request

confidential treatment of the documents listed below, associated with the certification application

referenced above.

Schematic(s)

Block Diagrams

Operational Descriptions

SOFTWARE SECURITY DECLARATION FOR U-NII DEVICES

Tune up

The documents above contain proprietary information not released to the public. Public disclosure of this

information may prove harmful to the business of the applicant.

SHORT TERM CONFIDENTIALITY

Additionally, the applicant requests the following documents be held confidential until the device is

marketed or 180 days from the grant date, whichever is less. If the device is marketed within

aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01

Confidentiality Request Procedures.

Print Name: JS Hsu

Title: Manager

External Photos

Internal Photos

Test Setup Photos

User manual(s)

Sincerely,

Signature:

On behalf of Company: DT Research, Inc.

Telephone: 886-2-2298-1039 ext. 309

E-mail: js_hsu@dtri.com

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia 30024

United States

Applicant Declaration

Applicant Legal Business Name

DT Research, Inc.

3RD FL NO 36 WUQUAN 7TH RD WUGU DISTRICT NEW TAIPEI Taiwan

Address

Grantee Code

FCC ID

Contact Email

Contact Phone

Authorized Contact Name

JS Hsu

YE3

YE3600-3165D2W

js_hsu@dtri.com

886-2-2298-1039 ext. 309

a)

b)

c)

d)

e)

I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my

knowledge and belief.

in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in

this application, the Applicant is responsible for:

(1)

(2)

(3)

labeling the equipment with the exact FCC ID as specified in this application,

compliance statement labeling pursuant to the applicable rules,

compliance of the equipment with the applicable technical rules,

if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure

that production units of this equipment will continue to comply with the FCC’s technical requirements.

in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible

party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321.

in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts

and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3)

the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS,

FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or

software required for evaluation, review, certification and audit surveillance of products certified by SGS.

f)

neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section

5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See

47CFR 1.2002(b) for the definition of a “party” for these purposes.

g)

the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions.

Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47

Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm

Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html

Applicant Signature:

Date: 2021-7-14

Print Name:

Title:

JS Hsu

Manager

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Applicant Declaration

Rev:0.0

DT Research, Inc. Request for Class II Permissive Change FCC ID: YE3600-3165D2W Date: 2021/07/19 To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Please be notified that we, the undersigned, (DT Research, Inc.) declare that the reasons for this Class II permissive change are as below:

--RF module used in this portable device requires SAR testing compliance of which is not performed and demonstrated in Modular approval.

-- Host product also contains a DT Research WLAN/BT Module which has been authorized under FCC ID:

YE3600-3165D2W dated on 03/23/2020.

--The antenna of the RF module used in this portable device has been replaced, and the replacement antenna specifications are shown in the following table:

Operation Frequency Antenna types, Antenna Gain Bluetooth: 2402MHz-2480MHz Bluetooth LE: 2402MHz-2480MHz PIFA Antenna, 2.7dBi PIFA Antenna, 2.7dBi 802.11b/g/n: 2412MHz-2472MHz/2422MHz-2462MHz PIFA Antenna, 802.11a/n/ac: 5180MHz-5240MHz, 5190MHz-5230MHz, PIFA Antenna, 5210MHz-5210MHz, 5260MHz-5320MHz, 5270MHz-5310MHz, Antenna1:3.1dBi, Antenna2:3.4dBi Antenna1:2.4dBi, Antenna2:2.7dBi 5290MHz-5290MHz, 5500MHz- 5700MHz, 5710MHz-5710MHz, 5720MHz-5720MHz, 5510MHz-5710MHz, 5530MHz-5690MHz, 5745MHz-5825MHz, 5755MHz-5795MHz, 5775MHz-5775MHz,

-- The RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Sincerely, Print Name: JS Hsu Signature:

Title: Manager On behalf of Company: DT Research, Inc. Telephone: 886-2-2298-1039 ext. 309 E-mail: js_hsu@dtri.com

Channel Statement

We, DT Research, Inc. declare that this EUT

(FCC ID: YE3600-3165D2W) doesn’t have ad Hoc Mode function on “non-US/Canada

frequencies“. In addition, the frequency selection feature is disabled by firmware for devices

marketed to the US/ Canada. For DTS part of this device, only channels 1-11 will be used in

North America. Country code selection is disabled.

Should you have any questions or comments regarding this matter, Please have my best

attention.

Print Name: JS Hsu

Title: Manager

Sincerely,

Signature:

On behalf of Company: DT Research, Inc.

Telephone: 886-2-2298-1039 ext. 309

E-mail: js_hsu@dtri.com

Federal Communications Commission Authorization and Evaluation Division March 19, 2020 ATTESTATION FCC ID: YE3600-3165D2W Product: WLAN Module Model: 3165D2W We dont provide any controls or software to allow operation outside the USA frequency band when we sell a product bearing the FCC ID: YE3600-3165D2W anywhere in the world. Sincerely,

Vincent Lin, DEKRA Testing and Certification Co., Ltd.

DT Research DTS-UNII Device Declaration Letter Date: April 10, 2020 To whom it may concern:

We have declared below featured for FCC equipment authorization, FCC ID: YE3600-3165D2W qd) DFS Device -- Oo Master , oO Client with Radar detection capability , EX] client without radar detection capability, (] N/A

(2) Active / Passive Scanning, adhoc mode access point capability Frequency Band Active Scanning Passive scanning Ad Hoc Mode or Access point

(MHz) (the device can (where the device is WIFI Direct transmit a probe can listen only with no capability

(beacon)) probes) 2412-2462 ves, [] No 2422-2452 Loves, KX] No ves, [No 5180-5240 Lives, K)No Klves, L]No |

5190-5230 Yes, _] No ; Lives, No |

5210-5210 ves, L] No ie ip Lives, KI No |

5260-5320 &) yes, [No |

5270-5310 |

& Yes, oO No 5500-5720 LJ No 5530-5690 5745-5825 is: KI No 5755-5795 Yes , J No This information when programmed into the EEPROM will not be accessible and can not be changed by the end user. If you have any questions, please do not hesitate to contact us. Signature, TSMoor JS Hsu / QA Manager

DT Researc Declaration of Authorization We Name: DT Research, Inc. Address: 3RD FL NO 36 WUQUAN 7TH RD WUGU DISTRICT City: NEW TAIPEI Country: Taiwan Declare that:

Name Representative of agent: Vincent Lin Agent Company name: DEKRA Testing and Certification Co., Ltd. Address: No.5-22, Ruishukeng, Linkou Dist., City: New Taipei City 24451 Country Taiwan, R.O.C. is authorized to apply for Certification of the following product(s):

Product description: WLAN Module FCC ID: YE3600-3165D2W Trademark: DT Research, Inc. on our behalf. Date: 2020/03/17 City: NEW TAIPEI Name: JS Hsu Function: QA Manager Signature; esses! l ssaa eens oe eet Wer waesnnr ous Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

Date: April 10, 2020 Declaration of Product Modifications This is to request a Class II permissive change for FCC ID: YE3600-3165D2W, originally granted on 03/23/2020 The major change filed under this application is:

#1: Additional Chassis added, DT Research, Inc., Model number: DT362GL. Assessed in Host. The host contains two modules:

1. FCC ID: YE3600-3165D2W (WLAN module) 2. FCC ID: QV5MERCURY6E-M (RFID module)

#2: Reduce the Output Power through firmware, and SAR measurement were evaluated.

(Only reduce Wi-Fi Output Power, Bluetooth Output Power haven't changes). For attest that the FCC guidance in KDB 996369 D02 Question 1 and KDB 996369 D04 for integrating modular transmitters into host equipment was followed for the preparation of this application under FCC ID: YE3600-3165D2W The equipment will include two transmitter modules. FCC ID for WLAN module is YE3600-3165D2W which is granted on 03/23/2020 by Change in Identification; and FCC ID for RFID Card is QV5MERCURY6E-M which is granted on 01/24/2020 by Original Equipment application). Antenna specifications for these modules are included within this filing. Sincerely,

Vincent Lin, DEKRA Testing and Certification Co., Ltd.

FCC ID.: YE3600-3165D2W Date: April 10 ,2020 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application as outlined below:

Type of Confidentiality Requested Exhibit Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent Permanent Block Diagrams External Photos Internal Photos Tune-Up Procedure Schematics Test Setup Photos Users Manual Operation Description/Theory of Operation Parts List & Placement/BOM The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Sincerely,

Vincent Lin, DEKRA Testing and Certification Co., Ltd.

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Date: March. 19th, 2020 To Whom It May Concern, Subject: Declaration of Changing ID, FCC ID: YE3600-3165D2W We, DT Research, Inc., would like to proceed a change ID project. Original application information:

Company name: Intel Mobile Communications FCC ID: PD93165D2 Product name: Intel Dual Band Wireless-AC 3165 Model name: 3165D2W Original issued date: July. 1, 2015 We would like to market the above referenced product under our FCC ID:

YE3600-3165D2W and part no. is 3165D2W. All other hardware and software is identical with original granted. This application has been authorized by Intel Mobile Communications. We would like to declare that YE3600-3165D2W is electrically identical and the only changed is the label on the device. The original test results continue to be representative of and applicable to the changed equipment. Sincerely, ___ _____________________ Vincent Lin, DEKRA Testing and Certification Co., Ltd.

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Re: Change of Identification Authorization, FCC ID: PD93165D2 Date: Mar. 11th, 2020 To Whom It May Concern:

This letter grants authorization for representatives of DT Research, Inc. to apply to the FCC for a change in identification as specified under 47CFR2.933 of the FCC rules. This authorization applies to the Intel Corporation, Intel Wireless 3165, 802.11a/b/g/n/ac+ BT SD form factor, model: 3165D2W, FCC ID: PD93165D2, approved on 07/01/2015. We are aware that DT Research, Inc. intends to market the above referenced product under their FCC ID: YE3600-3165D2W, part number 3165D2W. Sincerely, Date: Mar. 11th, 2020 Steven C. Hackett Wireless Product Regulatory Engineer Mobile Wireless Group Intel Corporation Intel Mobile Communications 100 Center Point Circle, Suite 200 Columbia, South Carolina 29210 USA