Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable Switch Selectable 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W 5W - 2W VVVVVideo T ideo T ideo T ransmitter ransmitter ideo Transmitter ransmitter ideo T ransmitter VVVVVideo T ideo T ideo T ransmitter ransmitter ideo Transmitter ransmitter ideo T ransmitter VMS-5000 Frequency 2450-2500 MHz DTC COMMUNICATIONS INCORPORATED How to contact DTC For operator and troubleshooting information, customers are encouraged to refer to the details in this manual. For additional clarification or instruction, or to order parts, contact DTC. Customer Service is available Monday through Friday between the hours of 9:00 AM and 5:00 PM EST at:
Tel: 603-880-4411 Fax: 603-880-6965 Website: www.dtccom.com Email: info@dtccom.com 486 Amherst Street Nashua, New Hampshire 03063 USA Inc. All translated Copyright Notice Copyright 2003 DTC Communications, rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a re-
trieval system or into any language or computer language, in any form or by any means, including but not limited to electronic, magnetic, mechanical, optical, chemical, manual or otherwise, without the prior written permission of DTC Communications, Inc. Disclaimer The information in the document is subject to change without notice. DTC makes no representations or warranties with respect to the contents hereof, and specifically disclaims any implied warranties of mer-
chantability or fitness for a particular purpose. DTC reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of DTC to notify any person of such revision or changes. Trademarks Trademarks of DTC Communications, Inc. include:
Warranty DTC warrants its manufactured components against defects in material and workmanship for a period of two (2) years, commencing on the date of original purchase. Products manufactured by others that are approved for use with DTC equipment are warranted for the manufacturers warranty period, commencing from the date of shipment from DTC. FCC information Forms can be obtained from the FCC on their web-
site at:
www.fcc.gov You can also contact the FCC using their FAX back service at: (888) 418-3676 Additional instructions are available by telephone at:
(888) 225-5322 The filing fee form is returned to:
Federal Communications Commission 1270 Fairfield Road Gettysburg, PA 17325-7245 DTC
MiniPIX
DynaPIX Other product names used in this manual are the properties of their respective owners. 2 OP1920187 Rev A Manual Conventions NOTE Describes special issues you should be aware of while using a particular function. WARNING Calls out situations in which equipment could be damaged or a process could be incorrectly imple-
mented, but in which operator safety is not a factor. TIP Describes application hints. RF EXPOSURE STATEMENT This product is NOT recommended for use in body-worn applications. Refer to Appendix A in this manual for instruc-
tion in the proper use of antennas with this device. When in use a seperation distance of at least 20 cm must be maintained between the supplied antenna and the body of the user or nearby persons. At this distance the field density will be 1.61 mW/cm2, well below the maximum permissable exposure level of 5. mW/cm2. Note: This device is for occupational use only. Occupa-
tional users are those persons who are exposed as a consequence of their employment, provided these persons are fully aware of and exercise control over their exposure. See Appendix A. Antenna Safety. FCC ID# H25VMS5000 TABLE OF CONTENTS Kit Contents ......................................................................... 4 Quick Start ............................................................................ 5 Encryption ............................................................................ 6 Heat Considerations ........................................................... 7 Mounting Options ................................................................ 8 Reinstalling Heatsink .......................................................... 9 Connectors ........................................................................ 10 Connections ...................................................................... 11 Basic Video Transmitter .................................................... 12 Single Power Source ......................................................... 13 Components ................................................................ 14-16 Programming ............................................................... 17-20 Specifications ............................................................... 21-23 Features ............................................................................ 24 Warranty ............................................................................. 25 Appendix A. Antenna Safety ................................................ 26 3 TYPICAL KIT Programming Cable with Power Adapter Screwdriver Antenna
(ANT-VIX) Adapter RCA(F) to RCA(F) Cable for Camera Power 2.1mm to Molex Included with your 5 Watt -2 Watt Transmitter:
VMS-5000 Video Transmitter packaged in case with heatsink attached
Accessories kit containing:
DTC programming software package
DTC programming cable
Camera Cable
Dipole antenna with right angle SMA connector
Video and Power In Y cable
Four captive mounting screws
Transmitter mounting bracket (optional) 2W-5W Video Transmitter with Heatsink Multi I/O Cable for Transmitter Power, Camera Power and Video AC 100-240V Power Adapter with Molex Connector 4 NOTE: DTC has provided you with a Y cable (power and video) terminated with an RCA connector and a BNC adapter for your convenience. NOTE: The dipole antenna included is not recom-
mended for normal use! This antenna enables you to quickly set up your transmitter and ensure proper operation. DTC highly recommends the use of circularly polarized antennas for the best rejection of multi-path. 1 Make sure that the external power source to the transmitter is OFF. 2 Using a screwdriver, turn the channel selector to the correct channel number. 3 Connect an antenna to the ANTENNA connector on the module. 4 Select Hi or Lo Power using the recessed switch. 5 Connect the microphone or microphones to the MIC-1 and MIC-2 connectors on the module. 6 Connect a video source and external power (11 -16 VDC) to the Video/Multi-I/O connector. 7 If you are using an (optional) Encryption model, choose Encrypted (SCR) or Clear (CLR) as desired 8 Apply power to the transmitter. Warning: Do not apply power to the transmitter until an antenna has been connected in step 3. 5 QUICK START 7 6 3 4 2 5 As an option, the transmitter can be equipped with an encryption module with a two position switch. In the CLR
(clear) mode, clear analog microwave video is transmitted. In the SCR (scrambled) mode, the video will be scrambled and capable of being decoded by a compatible receiver only. Note: The scrambled transmission mode is recom-
mended. Casual scanners will not be able to decode the signal and see what is being transmitted. SCR position = ON, CLR position is OFF ENCRYPTION OPTION Top View 4 8 1.1 CLR SCR SCRAMBLER
.33 Screws Screws Side View Heatsink, Transmitter, and Encryption Heatsink Transmitter Encryption 6 NOTE: NEVER remove the heatsink. NOTE: HOT SURFACE MAY CAUSE BURNS. Ensure that transmitter is properly ventilated and allow to cool before touching. Heat is an enemy of electronic components so it is impera-
tive that the transmitter is not allowed to exceed 80 degrees C. With the heatsink removed, the temperature would rise to 125 degrees C or more, which would be destructive to the internal components. At 125 degrees C, the unit would also deliver a serious burn if touched. Much of the heat is given off by the final output transistor, which is the most critical component when it comes to heat considerations. The heatsink is shipped mounted to the transmitter with four 6-32 screws, and has two additional 4-
40 screws attached from the fin side of the heatsink to the transmitter around the final output transistor. These screws are critical for thermal conduction from the transmitter to the heatsink. Removing these screws is not recommended. If you plan to mount the transmitter, be sure to orient the heatsink fins vertically for effective heat dissipation. Use one of the recommended mounting procedures presented on the next page. HEAT CONSIDERATIONS BEST: Fins Vertical Fins Vertical Fins Vertical Away From Wall Away From Wall Against Wall Wall GOOD: Fins Up NEVER: Fins Horizontal Fins Down 7 MOUNTING OPTIONS NOTE: ALWAYS mount the transmitter with the heatsink fins oriented vertically for proper heat dissipation. NOTE: Leave room for the antenna and/or connectors when selecting a mounting surface. The supplied antenna requires more than 5-inches of space. Option One The transmitter and heat sink can be mounted (with cooling fins vertical) against a heat-conductive metal surface. The transmitter ships with four additional 6-32 pan head Phillips mounting screws. Remove the four 6-32 Phillips screws from the front of the transmitter.
Install the four long 6-32 Phillips screws supplied. The screws become captive.
Pass the screws through the mounting surface and install nuts to secure the assembly. Option Two An optional wall-mount bracket is available from DTC Communications, which will allow simple mounting on a variety of surfaces and enclosures.
Loosen the four 6-32 Phillips screws from the front of the transmitter.
Install the bracket in the orientation shown. Retighten the four Phillips screws. Hang bracket on wall using #10 screws. 8 Option 1 Mounting Scheme 2.420 1.125 1.475 Option 2 Mounting Scheme NOTE: The transmitters baseplate operating tempera-
ture is -30 to + 80C. The heatsink is always required. Removing the heatsink is not recommended as excessive heat can destroy the device The transmitter is shipped with the heatsink attached. Removing the heatsink is not recommended. If, due to your particular situation, you find that you need to reinstall the heatsink, refer to the steps provided here. To re-install the heatsink:
1 Ensure the chassis and heatsink surfaces are clean. If needed, use rubbing alcohol to clean, then dry. 2 Align the transmitter and heatsink, with the back of the transmitter mating with the front, flat surface of the heatsink. 3 Secure the heatsink with four (4) 6-32 x 1 screws
(1-1/2 screws if using encryption model). Install the screws from the transmitter side. 4 Make sure there is good contact between the transmitter and the heat sink. They should be mounted flush to one another. 5 IMPORTANT Two 4-40 screws must be installed on the outside (fin side) of the heatsink to tighten the heat-
conductive surfaces nearest the final output power transistor. These screws are essential for proper heat dissipation. Do not operate the transmitter with these screws removed. Screw must not exceed 0.125 depth into transmitter or it will bottom-out and not provide proper heat-conduction. NOTE: Make sure to install all factory-provided hardware to secure heatsink to transmitter for optimal thermal conduction and heat dissipation. The temperature must never exceed 80 Deg. C. REINSTALLING HEATSINK 2.56 1.40 3.340 1.865 3.340 1.865
.000
.000 9 CONNECTORS Microphone Connectors Antenna Connector WARNING: Refer to Appendix A of this manual for information on the proper use of antennas. 10 MATING CONNECTORS Lemo Male Part # (FFS.01.250.DLAE31) DTC Male Part # (8570003) Hirose Part # HR10A-7P-6P (02) DTC Part # 954020 Standard Male SMA Connector MICROPHONE CONNECTORS Two connectors accommodate two microphone inputs. Each connector has two contacts and provides power to the microphone as well as connecting the audio signal into the transmitter. The audio sub-carriers are activated by the presence of the microphone. If a microphone is removed, that sub-carrier is removed from the transmit signal. Turning off the unused sub-carrier saves power and improves picture quality. ANTENNAS A standard SMA connector is used as the antenna connector on both the VMS-5000. Refer to a list of DTC antennas available on page 16. TIP: You may use the VMS series transmitters with other manufacturers antennas. Verify that they are suited for the band you are operating in. CHANNEL SELECT SWITCH Select a transmission channel by using the rotary switch located on the front surface of the transmitter. Use a screwdriver to rotate the switch to the desired channel number. HI/LOW OUTPUT POWER SWITCH Select Hi or Low power by using the recessed power switch. Switching to Hi power is equal to 5 Watt output power. Switching to Low power is equal to 2 Watt output power. MULTI I/O CONNECTOR The multi I/O (6-pin Multi I/O) connector is mainly used as the video and external power input connector. It also provides access to many transmitter functions, such as:
Programming the device
Video in
Power in
Remote on
Camera power CONNECTIONS Channel Select Switch HI/LO Power Switch Multi I/O Connector Pin 6:
Video in Pin 5:
RS-232 in Pin 4:
Remote on switching to ground Pin 1: Ground Pin 2: Ext power input 11-16VDC Pin 3: Camera Power Output 11 BASIC VIDEO TRANSMITTER Cable 4045171-024 AC Power Supply Camera 9-16 V Power Source For Transmitter Only Stripped & Tinned Leads Standard 12 Antenna Transmitter The basic VMS-5000 configuration consists of the video transmitter, dipole antenna, and DTC cable part number 4045171-024. This cable is connected to the multi I/O port of the transmitter.
Camera Power It is configured to supply:
The video signal to the transmitter from the camera. Power to the transmitter through a molex connector that can easily be connected to DTCs battery pack. It also comes standard with stripped and tinned leads for a customer suppled power source. A recommended DTC battery pack is listed below and shown in the illustration:
4045177 (Optional D-Cell battery pack) Alkaline The cable does not supply power to the camera. The camera is powered separately with a customer-supplied power source. DTC offers other cables that will supply power to the camera as an option.
The VMS-5000 configuration, which uses the loop through power source for the camera, consists of the video trans-
mitter, dipole antenna, and DTC cable part number 405189-
024 . This cable is connected to the multi I/O port of the transmitter. It is configured to supply:
The video signal to the transmitter from the camera. Power to the transmitter through a molex connector that can be easily connected to DTCs recommended battery pack. Power to the camera through a molex connector that can easily be connected to DTCs optional cameras. 4045177 (Optional D-Cell battery pack) Alkaline NOTE: You will need separate external camera power compatible with the camera you use unless:
Voltage requirements are compatible with the 11-16 VDC requirements of the transmitter Camera current requirements do not exceed 200 mA Your main external power supply provides adequate battery life SINGLE POWER SOURCE Cable 405189-024 AC Power Supply Camera Stripped & Tinned Leads Standard Internal Loop Camera Power Loop Through Power Source For Transmitter
& Camera 11-16 VDC Antenna Transmitter 13
COMPONENTS Part Number 4045171-024 Specifications Video In:
Ext. Power:
Description Video In/EXT Power/Cam. Power cable, 24standard. Multi I/O to RCA(M) with BNC adaptor
(YELLOW) 24 AWG wire with a molex connector and stripped and tinned leads. (RED) Part Number 4045189-024 Specifications Video In:
Ext. Power:
Camera Power:
Description Video In/EXT Power/Cam. Power cable, 24standard. Multi I/O to RCA(M) with BNC adaptor
(YELLOW) 24 AWG wire with a molex connector and stripped and tinned leads. (RED) 24 AWG wire with a molex connector and stripped and tinned leads. (GRAY) 14 Part Number 4045174-006 4045174-012 Specifications Connectors Description Antenna Cable 6 standard Antenna Cable 12 Option SMA to TNC Part Number 7011145-012 7011145-024 7011145-036 7011145-048 7011145-072 7011145-144 7011145-360 Description Microphone, 12 length Microphone, 24 length Microphone, 36 length Microphone, 48 length Microphone, 6 length Microphone 12 length Microphone 30 length Part Number 400023 Description 12 Volt 2.5 AmpPower Supply 100-240 VAC input Part Number 4045173 Description Programming cable (Connects from the Multi I/O connector to the DB9 connector) This cable plugs into COM1 or COM2, serial ports of a PC. It allows for the programming of the Video transmitter with the DTC Programming software. COMPONENTS TO CLOSE:
PUSH CONNECTORS TOGETHER UNTIL THE MOLEX LOCKING MECHANISM CLICKS AND LOCKS TO OPEN:
TO OPEN:
PUSH THIS TAB DOWN TO RELEASE THE MOLEX LOCKING MECHANISM, THEN PULL CONNECTORS APART. Part Number 8590138 8550104 Part Number 8590139 8550101 Description Terminal, Crimp, Female, micro-fit
(3.0) wire size 20-24 AWG plt gold. Molex Part # 43030-0009 Receptacle, 2 circuit, micro-fit (3.0) in line. Molex Part # 43645-0200 Description Terminal, Crimp, Male, Micro-fit (3.0) wire size 20-24 AWG plt. gold. Molex Part # 43031-0009 Plug, 2 circuit, Micro-fit (3.0) In line. Molex Part # 43640-0200 15 COMPONENTS Part Number 1088518 Description Optional Mounting Bracket 1087456 Captive Screw-No Encryption (4) 1087457 Captive Screw-With Encryption (4) Part Number VMS-5000-ENL Description The 5Watt - 2Watt Transmitter with Encryption VMS-5000 The 5Watt - 2Watt Transmitter Part Number Description ANT-VIS Dipole Antenna 2.4-2.5 GHz with right angle SMA adaptor The ANT-VIS is a 1/2 wave coaxial dipole portable duck antenna. It can be mounted directly to the video transmitter, or at a right angle using the adaptor provided. 16 Part Number 1088307 Description The 5Watt - 2Watt Heatsink PROGRAMMING Introduction DTC has built in a lot of flexibility in the programming options you have on the VMS series transmitters. You can choose to use some, all or none of this flexibility. When you order a VMS transmitter, DTC will factory program your frequencies at no additional charge to you. You may want to place a sticker over the rotary switch on the chassis, so users in the field dont attempt to change frequencies. This is often the best path for state and local agencies with limited frequencies available to them. DTC will also provide you with free software and a free programming cable, enabling you to change your video frequencies and their associated audio sub-
carriers. This is ideal if you often work with other agencies, or anticipate the equipment being used by a multi-jurisdictional task force. You can program up to ten channel settings per unit. In general, this allows you to program most varia-
tions you might encounter in the field at the depot level. As a practical matter, your VMS transmitters video frequencies and audio sub-
carriers will be dictated by the frequency and sub-carriers(s) of your receiver and/
or repeater. In many cases, these devices are crystal controlled or have few channel options. TIP: Make sure that you program your transmitter to match the frequencies and audio sub-carriers on your receiver, and test the components as a system prior to going into the field!
17 PROGRAMMING Installing DTC Universal Programming Software on your PC NOTE: Uninstall any previous versions by going to Add/Remove Programs, clicking on DTC Universal Programming, and clicking on uninstall. 1 Click on Start, click on run. 2 Click on the Browse button. 3 Click on or find your CD drive. 4 Install the JAVA Runtime Environment Application first (CD provided). 5 Follow the install wizard screens. 6 Install the Universal Programming software next (floppy provided). 7 Click on Start, click on run. 8 Click on the Browse Button. 9 Click on your floppy drive. 10 Double click on the setup. 11 The Mask References dialog box displays. Select NO for normal installation. Select YES to hide references to DTC (for covert operations). 12 Follow the install wizard screens. Your programming software is installed. 18 1 Make sure that the power to the video transmitter is off. 2 Make sure the transmitter has an antenna installed into 3 the antenna connector prior to programming. Install the programming cable into the Multi I/O connec-
tor on the transmitter. 4 Plug the serial cable of the programming cable into the COM1 or COM2 port of your computer. 5 Connect the programming cable into a power source. 6 Select Start, programs, DTC communications on your computer. 7 The system allows you to select device COM1 or COM2, depending on which serial port you are connected to. 8 Follow the instructions on the DTC Universal Program-
ming screens to begin the download process. PROGRAMMING 5 AC POWER 4 COM1 or COM2 Serial port of computer 2 3 6 7 8 19 PROGRAMMING 9 Click on the Tx Channel tab in the programmer screen. 10 Select a channel and click on the Edit Channel button to change settings. 11 Enter your new frequency and settings. 12 To change any of the MIC-2 or MIC-1 settings, click on the settings provided, 9 then click OK. 13 Click on the Upload button to upload your new settings to the transmitter. Your new settings have been installed. 13 10 11 12 20 General Specifications Item Power Input Voltage Power Consumption Reverse Polarity Protection Chassis Dimensions Encryption Model HeatSink Available Camera Power Controls Connectors Programmability Chassis notes Environmental Factors Specification External 11-16 Vdc 18 Watts YES 3.9 x 2.7 x 0.512 3.9 x 2.7 x 0.842 2.88 x 1.825 x 4.375 Dependent upon voltage supplied to the transmitter. Current limited to 200 mA. 10 channel select rotary switch Panel mounted, recessed slide power selection switch 2 pin Lemo: Mic 1 2 pin Lemo: Mic 2 SMA: Antenna 6 pin Multi I/O: Video in, Data in, DC input 11-16 Vdc, camera power, Remote ON/OFF, Multiplexed Data out, Ground 10 channels per selected band 250 KHz resolution steps Audio: User programmable from 6.0-7.5 MHz, in 10 kHz steps Machined, solid aluminum with rounded edges.
-30EC to +80EC Temperature 90% Humidity (non-condensing) SPECIFICATIONS RF Specifications Item Operating Frequency Specification 2450-2500 MHz, 250 KHz resolution steps Power output Output Impedance Spurs and Harmonics output Load Pull Stability Frequency Stability +/-
Modulation Sensitivity Modulation Sensitivity Variation Peak Carrier Deviation Number of channels Sub-carrier sideband level 5.0 W max. @ nominal supply voltage, 25 Deg. C.
-3db @ 7VDC ext. -2 dB over temp. 50 Ohms
-50 dBc 8:1 VSWR 0.003%, -30 to +50C 8 MHz/V nom.
+/- 5% across the band 4 MHz nom. 10 max. (user programmable)
-28 dBc, +/- 2 dB 21 Video Specifications Item Video Frequency Response Input Impedance Input Level S/N Pre-Emphasis Differential Gain Specification BW1.5dB = 6 Hz - 5.0 MHz 75 Ohms 1Vp-p M 60 dB min. Per CCIR 405 525 line curve 5%
SPECIFICATIONS Audio Specifications Item General Number of sub-carriers Sub-carrier frequencies Sub-carrier ON/OFF Control Subcarrier Frequency Stability Sub-Carrier Deviation Audio S/N Frequency Response Total Harmonic Distortion Input Level Pre-Emphasis Input Impedance Specification Mic level input (line level factory opt.) 50-3000 Hz Phased locked AGC on both inputs. Sub-carrier auto sensing, only active when microphone is attached. 2 6.0-7.5 MHz , user programmable Subcarriers are activated when mic is connected.
+/- 0.003%, -30 to +70C 50 kHz peak 45 dB min. BW1.5dB = 50-3000 Hz
<2%
8 mVpp@400 Hz for 50 kHz peak dev. 75 S 10k 22
) A i
n a r D t n e r r u C SPECIFICATIONS Approximate VMS-5000 Current vs. External Supply Voltage
(Camera NOT included) 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 11 12 13 14 External Supply Voltage (Vdc) 15 16 Battery Type Part Number Transmitter Only 10 D Cell Alkaline Pack 4045177 7 hours Transmitter @ 5 W
& Camera 12 V @
180 mA 6 hours 23 FEATURES The VMS transmitters are small module transmitters designed for off-body applications. They are part of a family of video transmitters from DTC that provide 250 mW, 2 Watts and 5 Watts output power. Feature Programmable Audio Sub-Carriers Efficient Switching Power Supply External Power Loop Through Description User programmable video channels, selectable in 250 kHz steps. Two user programmable audio sub carriers, selectable in 10 kHz steps from 6 MHz to 7.5 MHz. Audio sub carriers are OFF unless microphones are connected. The transmitter automatically senses when a microphone has been connected. The audio sub carriers are phase locked, and will not drift into the video signal. Automatic Gain Control is provided on each audio input, amplifying soft sounds. They generate far less heat than traditional video transmitters. They operate significantly longer than traditional video transmitters on the same power source. The power applied to the Multi I/O pin is automatically looped through the unit, and available on a second pin to power a remote device, such as a camera. If you apply 12 Volts in, you will get 12 Volts out, with a maximum current drain of 200mA Encryption Options The VMS series supports Ovation Micro ViewLock IIencryption, which adds approximately 0.35 to the thickness of the unit. 24 Appendix A Antenna Safety Using Antennas with the VMS-5000 Video Transmitter Use an antenna suitable for 5-Watt operation, however to ensure safe operation, it is imperative that proper spacing be maintained between the radiating surface of the antenna and any persons body. All RF category Mobile equipment must by law use a separation distance of 20 cm. The antenna supplied should not be placed closer than 20 cm (8in) to the body. To ensure that proper spacing is maintained, locate the transmitter or arrange physical barriers in such a way that people are prevented from approaching too closely. Limit your exposure to the antenna when the unit is in operation. 25 486 Amherst Street Nashua, New Hampshire 03063 603-880-4411 www.dtccom.com