FCC ID: 2AYPE-GWNC31514 laptop

GWNC31514 This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may causeundesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Quick guide Charging the Notebook Please charge your Notebook fully before using it for the first time. Connect the DC plug on the supplied power adapter to the charging socket (DC IN) on the Notebook. Then plug the power adapter into a socket. The charging LED lights up while the device is charging. Only leave the power adapter connected to the socket until the battery of the battery of the Notebook is fully charged. In addition, always disconnect the power adapter from the Notebook when you are not charging the Notebook. it is standing at a minimum angle of 90 to the Turning on the Notebook for the first time Bring the screen upwards until keyboard. Press the on/off switch for about 5 seconds to switch on the Notebook. The setup assistant will then appear on the screen. Follow the setup assistant instructions to set up your Notebook. During the start-up, the wizard prompts you to register for your Microsoft account. If you do not yet have a Microsoft account, please set one up here After completion of the start-up, your Notebook is configured This may take several minutes to complete. Do not turn the Notebook off during this time !

Unlocking the display As soon as the device has been set up (and every time it is subsequently switched on and booted up), the lock screen appears, Press any key on the keyboard to unlock the screen. If your Notebook is password-protected, you must then enter the password. Alternatively, you can also log into your Notebook via Windows Hello. To activate and set up this feature, select Settings Accounts Sign-in options Windows Hello. Start menu To display the start menu, click the Windows icon in the bottom left of the display or press the the Windows button on the keyboard. Press the icon a second time to hide the Start menu. The Start menu consists of the classic navigation list (A) and a useful app area (B) to the right of the navigation list. Among other things, the navigation list includes a link to open Settings (cog wheel icon).In the app area, you can pin apps and favourites in the form of live tiles and organize them. In the navigation list (A) you find a list of all installed apps in alphabetical order. An alphabetic quick access to the navigation list appears when you click on a respective first letter. The Action Center The Info Center is a bar with quick links to some important Notebook functions, which you can either display or hide. To access the Info Center click the memo symbol in the bottom fight-hand corner. Activating WIFI and opening the browser a. Call up Settings(see Start menu). b In the settings, click Network & Internet. c Click Wi-Fi on the left in the next screen. d Click the slider or the word Off. The word On now appears next to the slider. The Notebook searches for all available for all available wireless networks nearby and then displays them as a list (Show available networks). e Click the network that you wish to connect to. f g . Click Connect. The Notebook connects to the selected network. Enter the network key (password) if necessary. The button for launching the Internet browser can be found on the task bar at the bottom of the display. Click the little blue e to launch the browser. To enter an Internet address (URL), click the search bar displayed centrally at the top of the window. Reset If the Notebook freezes and no longer responds, you can reset it. Please and hold down then on/off switches off. Wait for about 20 seconds and then turn the Notebook on normally. Any files that have not been saved will be lost when the Notebook is reset. Switching off the Notebook Standby Briefly press the on/off switch on the device to activate the standby mode. Press it again quickly to take the Notebook out of standby mode. Shutting down Open the Start menu. Click in the bottom area of the Start menu and then tap Shut down. The Notebook shuts down. Saving energy Deactivate the WIFI function when it is not in use. Only leave the power adapter connected to the socket until the Notebooks battery is fully charged. In addition, always disconnect the power adapter form the Notebook when you are not charging the Notebook. Reduce the display brightness under SystemDisplay in the settings. Activate standby mode or turn off the Notebook completely if you are not using the Notebook. General safety information WARNING Risk of multiple injuries due ton reduced phsysical, sensory or mental capabilities and/or lack of knowledge or practical experience Children and vulnerable individuals may only use the device under direct supervision. Risk of electric shock or electrocution from live components Do not insert objects into the devices ventilation slots. Do not open the power adapter. Do not touch the power adapter if you hands are wet. Do not short out the device and/or charger. Fire hazard and or risk of burns from damaged or leaking batteries Do not use or charge the device if the battery if damaged or leaking. Do not use or charge the device if the battery is damaged or leaking. Avoid skin contact with the device and/or battery if the battery is leaking. Wear protective gloves if it is not possible to avoid touching the device/battery in such cases. Immediately wash your hands thoroughly in the event of skin contact with the battery substrate. If the battery substrate comes into contact with your eyes, rinse them out with plenty of water and consult a physician immediately. Risk of fire or explosion when using non-approved chargers and power adapters Only use the included power adapter or on an equivalent power adapter to charge the battery. If the power adapter is defective, only exchange it for an equivalent power adapter. Please note the information in the technical specifications of the power adapter in the online users manual or contact customer service. Risk of multiple injuries from slipping, tripping or falling Do not expose the device and/or power adapter to vibrations and/or any form of impact. Do not drop the device and/or power adapter. Do not use the device/power adapter if it has been dropped and/or is damaged. Have a qualified service technician check the device/power adapter before restarting it. Always ensure that the power cord is installed securely. Do not allow the power cord to knot or kink. Notes and practical tips on maintenance and repairs WARNING Risk of electric shock and electrocution from live components Never open the casing of the device and/or the power adapter. No parts inside the device require maintenance or cleaning. The battery in the device should not be removed by the user. Do not disassemble the battery, place objects into it or handle liquids near it. The battery could catch fire or explode. It is prohibited to repair or modify the device and/or power adapter. Failure to comply with these instructions may void the warranty. The device should only be serviced and repaired by a qualified service technician. Contact customer service where repairs or servicing are required.

24mm MODEL: GWNC31514-BK Gateway P/N: BL.9ESAG.364 FCC ID: 2AYPE-GWNC31514 MADE IN CHINA INPUT: 19V ==23.15A WiFi Fe C/S SUPPORT: (877)777-0649 WWW.GATEWAYUSA.COM I$ ____

E&S International Enterprises, Inc. Agent Authorization Company: E&S International Enterprises, Inc. Address: 7801 Hayvenhurst Avenue, Van Nuys, California 91406 Product Name: laptop Model Number(s): GWNC31514, N15TP9, C151, U151, T151, C152, U152,T152, C156, T156, GWNC31514-BK, GWNC31514-BL, GWNC31514-RD, GWNC31514-GR Product Description: laptop We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Ting Liu Title:

Manager Company:

E&S International Enterprises, Inc. Date: 2021-10-26

Date: 26 October 2021 E&S International Enterprises, Inc. To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

The E&S International Enterprises, Inc., the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen BALUN Technology Co., Ltd., to act on the behalf of the E&S International Enterprises, Inc. solely in matters relating to the application for an FCC equipment authorization for FCC ID: 2AYPE-GWNC31514 including the signing of documents in connection with this Application. Necessary acts carried out by Shenzhen BALUN Technology Co., Ltd. in connection with the Application shall have the same effect as acts of the E&S International Enterprises, Inc. The E&S International Enterprises, Inc. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Section 862. Yours Sincerely, _______ Ting Liu

Date: 26 October 2021 E&S International Enterprises, Inc. To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: E&S International Enterprises, Inc FCC ID: 2AYPE-GWNC31514 FCC Certification Confidentiality Request Gentlemen:

This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. E&S following documents regarding this submission for FCC ID: 2AYPE-GWNC31514 be kept confidential:

International Enterprises, Inc. requests that the Exhibit Type Block Diagram Schematics Operational Description Tune-Up Procedure Software Security Requireme nt Description File Name Block Diagram.pdf Schematics.pdf Operational Description.pdf Tune-Up Procedure.pdf General Description for UNII Devices.pdf And below exhibit kept short-term confidential (180 days):

External photos Test setup photos Internal photos User manual External photos.pdf test photo.pdf Internal photos.pdf User manual.pdf Those documents contain detailed system and equipment description and related information about the product which E&S International Enterprises, Inc. considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, E&S International Enterprises, Inc. considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours Sincerely, Ting Liu

29 Oct, 2021 To Whom It May Concern:

Declaration With regards to the application for Model: GWNC31514, According to the designer, E&S International Enterprises, Inc. we hereby declare that all models are same with electrical parameters and internal circuit structure, but only differ in model name. Brand Name: Gateway Product Name: laptop FCC ID2AYPE-GWNC31514 Basic Model Name: GWNC31514 Series Model Name: N15TP9,C151,U151,T151,C152,U152,T152,C156,T156, GWNC31514-BK, GWNC31514-BL, GWNC31514-RD, GWNC31514-GR Yours Sincerely, E&S International Enterprises, Inc. Charge Person Printed Name: Ting Liu

E&S International Enterprises, Inc. FCC Software Configuration Control Declaration Date: October 26, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: GWNC31514, N15TP9, C151, U151, T151, C152, U152,T152, C156, T156, GWNC31514-BK, GWNC31514-BL, GWNC31514-RD, GWNC31514-GR Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name:

Ting Liu Date: October 26, 2021 Title:

Manager Signature of applicant FCC Software Configuration Control Declaration Rev1.1