FCC ID: R72IM101 Private Land Mobile Radio for Vehicle (VHF)

E-Tech Co., Ltd. Installation requirements for compliance with Radio Frequency(RF) energy Exposure Safety Standards.

[ Warning ]

Your FM radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your FM radio complies with the following standards and guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans :

FCC OET Bulletin 65 Edition 97-01 supplement C, Evaluating compliance with FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE standard for Safety levels with respect to human exposure to radio frequency electromagnetic fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE recommended practice for the measurement of potentially hazardous electromagnetic fields RF and Microwave. DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio. ALWAYS use E-TECH authorized accessories (antennas, batteries, speaker/mics, etc). Use of unauthorized accessories can cause the FCC RF exposure compliance requirements to be exceeded. DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the TX Indicator lights red. E-Tech Co., Ltd. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits.

[ Important ]

Be sure that antenna installation is per chapter 5 of users manual. Electromagnetic Interference / Compatibility During transmissions, your Radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

E-TECH Co., Ltd 1/18 Table of Contents 1. Introduction 2. Description of Unit 3. Technical Specifications 4. Feature and operation 5. Antenna Installation FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 2/26 1. Introduction IM101 has a compact size with a various features in the range of 136~174MHz. Has a various features shown as below. IM101 constructed with a microprocessor controlled, temperature compensated Phase Locked Loop(PLL) frequency synthesizer. The radio features a double conversion receiver and a direct FM transmitter modulator. A special integrated circuit provides support to sub-audible signaling(CTCSS & DCS) and most of the receiving parts are switched off periodically in the power save mode to reduce battery current drain during standby. 2. Description of Unit Supplied Package Items Radio User manual Accessories Items Hand Microphone Battery Cable Pedestal Model IM 101 Model FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 3/26 3. Technical Specifications 3-1 General 1) Frequency range : 136~174 MHz 2) Channels : 255 Channels 3) Channel spacing : 12.5 kHz/25 kHz 4) Communication method : Simplex 5) Antenna Impedance : 50 ohm 6) Power supply voltage : DC 13.6V 7) Current Drain : When Transmitting(40W) - < 9A When Receiving(3W) - < 1A Transmit standby - < 150mA 8) Microphone : External Condenser Mic 9) Operating temperature range: -30

+60 10) Size : 178(W)x49(H)x195(D) 11) Weight : 1600g 3-2 Transmitter 1) Power Output : HIGH 40W, LOW - 5W 2) Modulation : 8K50F3E/16K0F3E 3) Oscillator method : PLL 4) Frequency Stability : less than 0.00025% (2.5PPM) 5) Maximum frequency deviation: 2.5 kHz(Narrow)/ 5 kHz(Wide) 6) Audio Distortion : less than 5% (1 kHz 60%) 7) SPURIOUS Emission : -75 [dBc]

8) FM Hum & Noise : -40 / -45 [dB] (HP8920A 300Hz 3kHz BP F) 9) BAND SPREAD : 38[MHz]

FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 4/26 3-3 Receiver 1) Receiver Type : Double Super Hetero type 2) Sensitivity : -0.25uV e.m.f ( 12dB SINAD ) 3) Frequency Stability : 0.00025%(2.5PPM) 4) SPURIOUS Rejection : -70 dB 5) Adjacent Channel Selectivity: -65 dB (Narrow) , -70 dB (Wide) 6) Distortion : 5% (1 kHz 60%) 7) Hum & Noise : -40 / -45 dB(HP8920A 300Hz 3kHz BPF) 8) Audio output : Normal 3W ( Max 5W ) 9) BAND SPREAD : 38MHz 10) Speaker size : 58 * 35 Oval 4. Feature and Operation EXTERNAL VIEW 1)POWER ON/OFF

& Volume control 2) LED 3)TX POWER HIGH/LOW 4)LCD 5)SCAN Button 6)SPEAKER 8)Squelch level 9)DOWN button 10)Menu Button 11)UP button 12) Monitor Key 7)Mic Jack &

PC-Programming Jack FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 5/26 4-1 Features & Operation 1. Monitor Press the Monitor key momentarily to disable the Tone squelch. 2. Radio Call By using Various 5Tone, individual / Group call is available. 16 Receiving codes are available as well as open call. 3. Missed calls list 16 Missed calls can be listed. If a call remains unanswered, the call will be stored by the radio. 4. contact list During a call, the contact list may be used to give access to up to 16 preprogrammed numbers accessed via the menu. 5. status list A status is a code for transmitting prearranged messages, e.g. status 05 may indicate launch. Status list contains up to 30 entries. 6. Channel : 255 channel 7. Scan ON/off 8. Power level : Power level is adjustable in each channel respectively. 9. Talkaround on/off 10. Emergency :

11. Lone Worker 12. Tx Tone select : In the menu, tx dcs /ctcss tone is adjustable. 13. Rx Tone select : In the menu, rx dcs /ctcss tone is adjustable. 14. Group : Defines group tone. You can select tone code for group, and it is used as a default value

. 0~9 and a, b, c, d available. And A is used as a basic value.. 15. BEEP ON/OFF : BEEP sound ON/OFF. 16. KEY LOCK : LOCK/UNLOCK Button KEY. 17. SQUELCH : Squelch level is adjustable 18. AUTO SQUELCH : Squelch level is adjustable automatically by surroundings. 19. DTMF ON/OFF : DTMF function is available. 20. VOX : VOX LEVEL is adjustable by pushing up and down button. 21. AUTO VOX : VOX level is adjustable automatically by surroundings. 22. P - SCAN : Priority Scan 23. POWER SAVE : Power save mode is available. 24. PASS WORD : This function is useful for security reason. 25. Dimmer : Control back light 26. SCRMABLE : Internal Voice Scrambler is available. 27. STUN / UNSTUN : For added security and to avoid abuse of the radio system in which you operate a feature known as Stun/Unstun is included in your radio. 28. BACK LIGHT : Lamp is lighting when you check LCD status. 29. Reset : Radio Data Reset. 30.MIC GAIN: Mic sensitivity control 31.Vari Call :Variable Call FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 6/26 4-2 LCD Display and Icons 1.ANT GAZE ; Shows the received signal strength. 2.TX POWER HIGH: Indicate power level 3.KEY LOCK: Appears during key lock function is ON. 4.ALART(BEEP) ON/OFF: Appears when beep sound is turned ON. 5.VOX ON/OFF: Appears when VOX function is turned On. 6.SCAN: Appears when Scan function is activated. 7.SCRAMBLE: Appears while the voice scrambler function is activated. 8.TALK AROUND Indicator. 4-3 Features 1. Channel This radio offers up to 255 channels 1). By using or button, you can select the desired channel. 2. Missed calls list Up to 16 calls can be stored. If the same radio calls more than once, only the most recent call is stored. When fifteen calls have been stored by the radio, depending on the radio programming the sixteenth call received may overwrite the first or not be stored by the radio. 1). to enter Menu Mode. 2) Display shows to select or to scroll list to exit 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 7/26 3. Contact list 1). to enter Menu Mode. or to until to select or to scroll list to exit 2) 3) 4) 5) 4. Status call list 4-1. Making STATUS call 1) to enter Menu Mode. 2) 3) or to until to select 4) 5) Push PTT KEY for sending message on the LCD. to scroll list or FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 8/26 4-2 Make STATUS Message 1) to enter Menu Mode. or to until to select or to scroll list to SELECT 2) 3) 4) 5) 5. Lone work 1). to enter Menu Mode. or to until to select or to select ON/OFF 2) 3) 4) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 9/26 6. Tx power

.1)

. to enter Menu Mode. or to until to select or to select HIGH / LOW POWER to select 2) 3) 4) 5) 7. Tx Tone Selecting Transmitting TONE(CTCSS/DCS). 1). to enter Menu Mode. or to until to select 2) 3) to Select TONE either CTCSS or DCS. 4) or 0= NON TONE 1-38 CTCSS 101 183 DCS TONE 5) to select exit FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 10/26 8. Rx Tone Changing Receiving TONE(CTCSS/DCS). 1). to enter Menu Mode. or to until to select or to select TONE either CTCSS or DCS. 2) 3) 4) 0= NON TONE 1-38 CTCSS 101 183 DCS TONE. to select exit 5) 9. Group Changing GROUP Tone. 1). to enter Menu Mode. or to until to select or to select scroll list to select exit 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 11/26 10. Beep on/off 1). to enter Menu Mode. or to until to select or to select on off . to select 2) 3) 4) 5) 11. Key lock 1). to enter Menu Mode. or to until to select or to select key lock /unlock. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 12/26 12. Squelch level 16 level is available. 0 = terminate sq function 1). to enter Menu Mode. or to until to select or to the scroll list to select exit 2) 3) 4) 5) 13. Auto Squelch 1). to enter Menu Mode. or to until to select or to select on /off . to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 13/26 14. Scan 1). to enter Menu Mode. 2) or to until 3) 4) Push PTT for exit to scan. 15. DTMF 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 14/26 16. Vox on/off 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) 17. Vox Level 16 level is available.. 1). to enter Menu Mode. or to until to select or to scroll list to select for exit 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 15/26 18. Auto Vox 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) 19. Priority Scan 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 16/26 20. Priority scan CH 1). to enter Menu Mode. 2) 3) 4) 5) or to until to select or to scroll list to select for exit 21. Power save 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 17/26 22. Talkaround 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) 23. Password 1). to enter Menu Mode. to until or to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 18/26 24. Password CH 1). to enter Menu Mode. 2) or to until 3) 4) ---- will display on the LCD( enter old password) to select or by pushing up and down KEY to change password. by pushing enter KEY to change digit of password. 5) Enter new password by 4 digit. 25. Dimmer Back light Control 1). to enter Menu Mode. or to until to select or to select level to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 19/26 26. Scramble 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) 27. Status call Send 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 20/26 28. Misscall List Delete 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) 29. Radio Reset 1). to enter Menu Mode. or to until to select or to select ON /OFF. to select 2) 3) 4) 5) FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 21/26 30. Variable call 1). to enter Menu Mode. or to until to select or to select 1,2,3~A,B,C,D,E to select 2) 3) 4) 5) 31. Mic Sensitivity Level (Mic Gain Control) 1). 2) to enter Menu Mode. or to until 3) to select or to select HIGH/LOW. 4) HIGH is high sensitivity and LOW is normal sensitivity FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 22/26

-Connector of Operation Antenna 10PIN CONNECTOR DESCRIPTION Connection Pin NO GND CPU_INT_PTT 5V FLAT_AUDIO_IN/OUT S/W_BATT CPU_RSSI_DET CPU_RX_PATH MIC CPU_SP_MUTE CPU_TX_PATH Function Ground Push To Talk Internal 5 Volt Regulator Constant Audio Signal Level Remark GND GND Enable 5 Volt Switched Battery 13.6V Enable Received Signal Strength Indication Busy Rx MIC Input Speaker ON/OFF MIC MUTE 5V Enable

(Rx Signal Open) 0V Enable

(Speaker Close) 0V Enable

(MIC Input Close) Power Supply & External Speaker Jack Connection Pin NO 13.6V GND Speaker OUT Function Power Cable Ground External Speaker Jack Remark 13.6V FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 23/26 5. Antenna Installation 5-1 Antenna Installation and Compliance with Radio Frequency(RF) Energy Safety Standards

[IMPORTANT NOTE]

To assure optimum performance and compliance with RF Energy Safety standards, this antenna installation guidelines and Instructions are limited to metal-body vehicles with appropriate ground planes and take into account the potential exposure of backseat passengers and bystanders outside the vehicle.

[NOTE]

For mobile radios with rated power of 7 watts or less, the only installation restrictions are to use only E-tech approved antennas and install the antenna externally on metal body vehicles. For mobile radios with rated power greater than 7 watts, always adhere to all the guidelines and restrictions in 5.2 below. 5-2 Selecting an Antenna Site/Location on a Metal Body Vehicle 1. External installation Check the requirements of the antenna supplier and install the vehicle antenna external to a metal body vehicle in accordance with those requirements. 2. Roof top For optimum performance and compliance with RF Energy Safety standards, mount the antenna in the center area of the roof. 3. Trunk lid On some vehicles with clearly defined, flat trunk lids, the antenna of some radio models (see restrictions below) can also be mounted on the center area of the trunk lid. For vehicles without clearly defined, flat trunk lids (such as hatchback autos, sport utility vehicles, and pick-up trucks), mount the antenna in the center area of the roof. Before installing an antenna on the trunk lid. Be sure that the distance from the antenna location on the trunk lid will be at least 60cm (24 inches) from the front surface of the rear seat-back to assure compliance with RF Energy Safety standards. Ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis. If these conditions can not be satisfied, then mount the antenna on the roof top !

4. Mounting restrictions for certain radio models For more than 40 Watt VHF models, the 1/4 wave antenna should be mounted only in the FILE: IM101 service manual.doc 2006.01.10 8 E-TECH Co., Ltd 24/26 center area of the roof, not on the trunk lid, to assure compliance with RF Energy Safety standards. 5. Ensure that the antenna cable can be easily routed to the radio. Route the antenna cable as far away as possible from any vehicle electronic control units and associated wiring. 6. Check the antenna location for any electrical interference. 7. Make sure any other mobile radio antenna on this vehicle is at least 30.48 cm (1 foot) away from this antenna.

[NOTE]

Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver interference. 5-3 Antenna Installation Procedure 1. Mount the antenna according to the instructions provided with the antenna kit. Run the coaxial cable to the radio mounting location. If necessary, cut off the excess cable and install the cable connector. 2. Connect the antenna cable connector to the radio antenna connector on the rear of the radio. 5-4 Completing the Installation 1. Mount the microphone clip to a convenient spot near your radio. 2. Your microphone has a telephone-type connector at the end of is cord. Plug the microphone into the control head connector. 3. To complete your radio installation, plug the power cable into the radio power connector. FILE: IM101 service manual.doc 2006.01.10