E-ZONE GUARDIAN T N O R F E D S N I I 1. ANTENNA PORT RADIO MODULE EZR 101-1000 D1 D2 OUT1 OUT2 IN 1 IN 2 2. JTAG PGM 3. USB PORT
+3.3VDC CPU P2.1 CPU P2.2 RESET_N GROUND GROUND USBP USBN
+3.3VDC
+3.3VDC OUT 1 TO +3.3V OUT 2 TO +3.3V IN 1 IN 2 USER DEFINED OUTPUT USER DEFINED OUTPUT USER DEFINED INPUT P1.2 TO GROUND USER DEFINED INPUT P1.3 TO GROUND 2. JTAG PGM 3. USB PORT 1. ANTENNA PORT CONNECTOR PCB MOUNT: HIROSE PART NUMBER H.FL-R-SMT(10) FCC CERTIFICATION COMPLIANCE USING DIGI INT'L. ANTENNA PART NUMBER A24-HASM-450. SUBSTITUTION OF OTHER ANTENNA MAY INVALIDATE FCC CERTIFICATION. THE E-ZONE RF MODULE IS INTENDED TO PROVIDE WIRELESS DATA TRANS-
MISSION BETWEEN TWO LINKED UNITS. THE RF UNIT ACCEPTS DATA OVER AVAILABLE CPU I/O LINES, STORES THE DATA AND PERIODICALLY TRANSMITS IT TO THE OTHER UNIT. DATA MAY MOVE IN ONE OR BOTH DIRECTIONS. UNITS WILL LINK ONLY WITH OTHER UNITS CONTAINING THE SAME INTERNAL ID CODES. UNITS MAY ALSO FUNCTION AS INTERMEDIATE RELAY BY LINKING BETWEEN TWO MODULES WHICH CANNOT COMMUNICATE DIRECTLY WITH EACH OTHER. THESE LINKING FUNCTIONS AS WELL AS THE RADIO CONTROL AND FEATURE FUNCTIONS ARE PREPROGRAMMED INTO THE MODULE WHICH UTILIZE TWO READILY AVAILABLE TEXAS INSTRUMENTS PROVEN COMPONENTS. THE CC2591 RF FRONT END INCLUDES PA,LNA,SWITCHES,BALUN, RF MATCHING NETWORK AND INDUCTOR, AND IS IMPLEMENTED TO INCREASE OUTPUT POWER AND IMPROVE RECEIVER SENSITIVITY ON A 2.4GHz LOW-
POWER RF SIGNAL PRODUCED BY THE CC2531, WHICH IS AN IEEE 802.15.4 COMPLIANT RF SYSTEM-ON-CHIP PROGRAMMED TO PROVIDE BOTH FREQUENCY HOPPING AND SPREAD SPECTRUM. THIS DEVICE COMPLIES WITH THE OPERATIONAL AND TIMING REQUIREMENTS OF SECTION 15.231(e) OF THE FCC RULES. THE TIMING REQUIREMENTS ARE PRESET AND FIXED AND NON-ADJUSTABLE BY THE END USER. K C A B WARNING: END USERS ARE RESPONSIBLE TO ASSURE COMPLIANCE WITH FCC RULES WHEN TRANSMITTING. END USERS MUST INCORPORATE ALL USER WARNINGS AND FCC REQUIREMENTS FOR THEIR EQUIPMENT IN OPERATIONAL MANUALS. INSTALLERS AND USERS OF THIS EQUIPMENT SHOULD BE AWARE OF THE RF EXPOSURE LIMITS SPECIFIED IN SECTION 15.247(b)(4) OF THE FCC RULES. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. OEM ENGINEERS USING THIS E-ZONE RF MODULE ARE CAUTIONED THAT THEY MUST INCLUDE IN THEIR OWN PRODUCT MANUAL THE FOLLOWING WARNING STATEMENT OF FCC PART 15.19:
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. SUPPLIED LABEL P/N 101-001003 OR "CONTAINS FCC ID O4UEZ12031"
MUST BE ON THE OEM USER'S FINAL PRODUCT. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. E-ZONE GUARDIAN, PO BOX 774, CEDAR HILL,TX 75106-0774 8-1-12 REV. 1.0