Quick Start Guide HD Wi-Fi Indoor Cube Model ID: EN-CCUC-001a V 1.0.1 Information for Users on Collection and Disposal of Old Equipment and used Batteries within the European Union These symbols on the product's, packaging or accompanying documents indicate that used electrical and electronic products and batteries should not be disposed together with household waste. For more information about collection and recycling of old products and batteries, please contact your dealer, point of sale or local municipality. In accordance with national legislation, penalties may be applicable for incorrect disposal of this waste. Information for disposal in Countries outside the European Union This symbol is only applicable in the European Union. When discarding these items please contact your dealer or local authorities for further information regarding the correct method of disposal. Eagle Eye Networks declares that this equipment is in compliance with the essential requirements and relevant provisions of the following directives:
Electromagnetic Compatibility (EMC) Directive 2014/30/EU Low voltage (LVD) Directive 2014/35/EU Radio equipment (RED) Directive 2014/53/EU This device complies with Part 15 off the FCC Rules for a class B digital device. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Declarations of Conformity for the relevant products described in this manual are available by sending a written request to:
Eagle Eye Networks B.V. Hogehilweg 19 1101 CB, Amsterdam The Netherlands Note:
This quick start guide is for reference only. All designs shown are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners. Please visit our website www.een.com or contact your local service engineer for further information. Video Pixels 3 Megapixel Max Resolutions 1920 x 1080 / 25fps, 2048 x 1536 / 20fps Lens Night Vision Field of View Dynamic Range 2.8mm IR LED with 10m range (33ft) H: 100 deg; V: 54.5 deg Wide Dynamic Range, Highlight Compensation, Backlight Compensation Digital Noise Reduction Yes Digital Image Stabilization Automatic Applications Image Sensor Iris Shutter Speed Min Illumination Digital Capabilities Video Compression Audio Compression Image Settings Interface Edge Storage Ethernet Wifi Audio Physical/Power Power Best for monitoring indoor areas: hallways, entrances & rooms 1/3"progressive scan CMOS Fixed 1/3s to 130000s Color 0.78 / F2.0; IR 0Lux / F2.0 H.264, MJPEG G.711a: G.711Mu: AAC Rotation, Saturation, Brightness, Contrast, Sharpness Micro SD Slot, Max 128GB RJ-45 Male 10/100 Base-T IEEE802.11b/g/n Microphone & Speaker DC12V Power Consumption 3W IR Off , <4.85 IR On Operating Temperature
-10C to +45C
< 95% RH CE, FCC 78.5127.8 mm 310 gram Plastic with Locking Ball Aimable Mount Operating Humidity Approvals Dimensions Weight Housing Device 1 QSG 1 Power Adapter 1 Screw Package 1 Installation Position Map 1 Figure 3-1 Figure 3-2 Figure 3-3 Please refer to the following sheet for more details about each port
. SN Name 1 2 3 4 5 6 7 8 9 Ethernet port (Wireless connection also available) Reset/WPS button (Wi-Fi Protected Setup) Digital input/output Power port Speaker Micro SD card slot Indicator light Microphone IR LED 10 Passive IR Sense IR ray, trigger alarm Sheet 3-1 Note:
For reset, press and hold for 8 seconds until the light turns off; For WPS (Wi-Fi Protected Setup) one quick press. Please refer to the following sheet for more details about the status of the indicator light. Indicator light status Device status Red light on Booting Green light slowly flashing Booting completed, awaiting Wi-Fi config Green light quickly flashing Wi-Fi smart config in progress, including WPS, management frame, etc. Green light on Wi-Fi connection succeeded, operating normally Red and green lights alternating Device upgrading Red light slowly flashing Network disconnection Red light quickly flashing Device failed to boot up; alarm or SD card does not work Sheet 3-2 Important Before the installation, please make sure the installation environment can support at least 3 x weight
(0.31Kg (0.68lb)) of the camera. See data sheet for further information. Figure 4-1 1. Paste the installation map on the installation surface. 2. Drill holes in the installation surface according to the installation map. 3. Insert the expansion bolts from the accessories bag to the prepared holes. 4. Attach the device with screws provided in the accessories bag. 5. Connect the cable and then boot up the device. 6. Loosen the adjust knob and adjust the camera to the required surveillance position. 7. Secure the knob of the bracket to fix the camera. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.